• Journal of Ocean Engineering and Technology
• /
• v.13 no.3 s.33
• /
• pp.49-56
• /
• 1999

Welding is a reliable process and is mainly adopted for fabricating heavy structures. Recently, transverse cracks in the weld metal is serious problem, and they affect cost, efficiency, safety and joint reliability for various welded structures. In this view of point, this study investigated the potential factors for weld metal transverse crack. The main results obtained are as follows; 1) The content of diffusible hydrogen in the commercial flux cored are welding wire was remarkable change by manufacturer. 2) The diffusible hydrogen content was thd main factor for weld metal transverse cracks. 3) Weld metal was immune to transverse cracking under the condition of low diffusible hydrogen content of high restraint condition. 4) The factors for weld metal transverse crack would be the content of diffusible hydrogen and restraint of weld joint.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.26-36
• /
• 2001

Smart sensors and actuators have recently been developed. In this study, first, small-diameter fiber Bragg grating (FBG) sensors developed by the author, whose cladding and polyimide coating diameters were 40 and $52{\mu}m$, respectively, were embedded inside a laminate without resin-rich regions around sensors and the deterioration of mechanical properties of the composite laminate. The small-diameter FBG sensor was embedded in $0^{\circ}$ ply of a CFRP laminate for the detection of transverse cracks in $90^{\circ}$ ply of the laminate. The reflection spectra from the FBG sensor were measured at various tensile stresses. The spectrum became broad and had some peaks with an increase of the transverse crack density. Furthermore, the theoretical calculation reproduced the change in the spectrum very well. These results show that the small-diameter FBG sensors have a potential to detect the occurrence of transverse cracks through the change in the form of the spectrum, and to evaluate the transverse crack density quantitatively by the spectrum width. On the other hand, shape memory alloy (SMA) films were used to suppress the initiation and growth of transverse cracks in CFRP laminates. Pre-strained SMA films were embedded between laminas in CFRP laminates and then heated to introduce the recovery stress in SMA films and compressive stresses in the weakest plies ($90^{\circ}$ ply). The effects of recovery stresses are demonstrated in the experiments and well predicted using the shear-lag analysis and the nonlinear constitutive equation of SMA films.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2013.12a
• /
• pp.55-59
• /
• 2013

Transverse vibrations of ship's aft end and deckhouse among the various modes of hull structures are induced mainly by transverse exciting forces and moments of main engine such as ${\times}$ and h-moment. Avoidance of resonance should be made in a intial design stage in case there is a prediction for resonance between main engine and transverse modes of deckhouse. This study shows a case of change in type of main engine from 12 cylinders to 10 without modification of hull structures in engine room requested by a shipowner of 8,600 TEU class container carrier and proposes a guide to the effective ways of structural arrangement for avoiding resonance between transverse exciting force and surrounding structures of main engine in engine room through case studies.

• The Journal of Korean Academy of Orthopedic Manual Physical Therapy
• /
• v.23 no.1
• /
• pp.23-30
• /
• 2017

Purpose: The purpose of this study was to investigate the effect of transverse abdominis ratio and balance ability during bridge exercises on different support surface. Methods: The subjects were 20 students at G University. Ultrasound equipment was used to measure the transverse abdominisratio and the computerized balance measurement equipment was used to measure the balance ability before and after bridge exercises on different support surface. Results: Transverse abdominis ratio change between the groups was a significant difference only in the unstable support surface training group (p<.05). Normal standing eye close balance ability change between the groups was significantly different only in the unstable support surface training group (p<.05). The changes in the transverse abdominis ratio after 7 days of exercise and 14 days after exercise were significantly different between the groups (p<.05). Normal standing eye close balance ability showed a significant difference at 7 days after exercise and 14 days after exercise (p<.05). Conclusions: It is more effective to balance ability and ratio of the transverse abdominis when bridge exercises on an unstable support surface than to perform bridge exercises on a stable support surface. Therefore, we propose an effective program for patients with instability of the lumbar in clinical practice. bridge exercises on different support surface.

• International Journal of Highway Engineering
• /
• v.16 no.2
• /
• pp.25-34
• /
• 2014

PURPOSES : This paper numerically evaluates the contribution of transverse steel to the structural behavior of continuously reinforced concrete pavements to understand the role of transverse steel. METHODS : Two-lane continuously reinforced concrete pavements with and without transverse steel were analyzed through finite element analysis with the aid of commercial finite element analysis program DIANA; the difference in their structural behavior such as deflection, joint opening, and stress distribution was then evaluated. Twenty-node brick elements and three-node beam elements were used to model concrete and steel, respectively. Sub-layers were modeled with horizontal and vertical tensionless spring elements. The interactions between steel and surrounding concrete were considered by connecting their nodes with three orthogonal spring elements. Both wheel loading and environmental loading in addition to self-weight were considered. RESULTS : The use of transverse steel in continuously reinforced concrete pavements does not have significant effects on the structural behavior. The surface deflections change very little with the use of transverse steel. The joint opening decreases when transverse steel is used but the reduction is quite small. The transverse concrete stress, rather, increases when transverse steel is used due to the restraint exerted by the steel but the increase is quite small as well. CONCLUSIONS : The main role of transverse steel in continuously reinforced concrete pavements is supporting longitudinal steel and/or controlling unexpected longitudinal cracks rather than enhancing the structural capacity.

• Journal of International Academy of Physical Therapy Research
• /
• v.7 no.2
• /
• pp.1066-1070
• /
• 2016

The purpose of this article was to investigate the effects of Maitland's transverse movement on change of pain, trunk flexion movement and Cobb's angle in patient with upper thoracic scoliosis. The subject are 37 years old with chronic low back pain participated in this study and has no experience surgery within the last six months due to back pain. 10 set was applied 10 times on the T3-T5 applied the transverse movement with grade IV to each segment by skilled physical therapist. Transverse movement was applied convex toward the concave side. Pressure pain threshold was reduced from 4/10 to 2/10. Trunk flexion range that is the distance between the middle finger and floor was increase from 7.3cm to 2cm. Cobb's angle was decreased from degree 18 to 16. This result demonstrated that the Maitland's transverse movement was benefit to reduce the pain and Cobb's angle, and to increase the trunk flexion movement.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.1
• /
• pp.16-23
• /
• 2004

Permanent magnet-excited transverse flux linear motor(TFLM) is known to have more excellent ratio of force to weight than any other linear motors. But, thrust generated by phase current is non-linear with regard to current and relative position like switched reluctance motor. This makes current and speed controller design difficult. This paper presents a method on minimization of thrust ripple of permanent magnet-excited transverse flux linear motor. Using genetic algorithm(GA), optimal current waveform can be found under the constraint conditions such as current limit, minimum of ohmic loss and limited rate of change of current etc. The effectiveness is verified through computer simulation and experimental test results.

• Journal of Advanced Information Technology and Convergence
• /
• v.9 no.2
• /
• pp.107-113
• /
• 2019

In this study, we examined the feasibility of considering the transverse edge effect of flat type linear induction motor as 2D finite element analysis (FEA) by changing the resistivity of secondary conductor. For this purpose, the 3D FEA analysis results were compared with the 2D FEA analysis results with the change of the resistivity of the secondary conductors. As a result, simply changing the resistivity could not accurately account for the transverse edge effect of LIM because of leakage components that could not be considered by 2D FEA.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.10 s.241
• /
• pp.1407-1415
• /
• 2005

Strength change of an over-aged A12024 material was studied after being subjected to stages of severe plastic deformation by ECAP (Equal Channel Angular Pressing). Various kinds of strength value were measured using the conventional tensile test, Rockwell and Vickers hardness and the SP (small punch) test Due to limitation of the specimen size, tension test in transverse direction could not be conducted. Hence, SP test was employed for assessing the strength in transverse direction. Based on TEM observation the measured strength characteristics were explained based on the relation between microstructure, dislocation and strength. As the number of ECAP pass increases, the strength of A12024 was also increased. However, considerable change of strength, which is generally predicted, was not observed in this study. For the strength in transverse direction even decrease of the strength was observed after 6 passes of ECAP. It was argued that this decrease was due to dynamic recovery of dislocation density during or after ECAP processes at $150^{\circ}C$. The strength assessment equation proposed by the authors in the previous paper was shown to be very accurate. This argument was supported by comparing the results of conventional tensile test with those of SP test. It was also pointed that the Rockwell har(3ness value seemed to be able to represent the strength in the transverse direction.

• Journal of the Korean Society of Safety
• /
• v.18 no.2
• /
• pp.34-39
• /
• 2003

In this paper, when CF/PEEK laminates for high efficiency space structure are subjected to FOD(Foreign Object Damage), the effects of temperature change on the impact damages(interlaminar separation and transverse crack) of CF/PEEK laminates and the relationship between residual lift and impact damages are experimentally investigated. Composite laminates used in this experiment are CF/PEEK orthotropic laminated plates, which have two-interlaces [$0^{\circ}_4/90^{\circ}_8/0^{\circ}_4$]. A steel ball launched by the air gun collides against CF/PEEK laminates to generate impact damages. And then CF/PEEK specimens with impact damages are observed by a scanning acoustic microscope under room and high temperatures. In this experimental results, various relations are experimentally observed including the delamination area vs. temperature change, the bending strength vs. impact energy and the residual bending strength vs. impact damage of CF/PEEK laminates.