• Korean Journal of Materials Research
• /
• v.33 no.11
• /
• pp.475-481
• /
• 2023

Recently, the electron transport layer (ETL) has become one of the key components for high-performance perovskite solar cell (PSC). This study is motivated by the nonreproducible performance of ETL made of spin coated SnO₂ applied to a PSC. We made a comparative study between tin oxide deposited by atomic layer deposition (ALD) or spin coating to be used as an ETL in N-I-P PSC. 15 nm-thick Tin oxide thin films were deposited by ALD using tetrakisdimethylanmiotin (TDMASn) and using reactant ozone at 120 ℃. PSC using ALD SnO₂ as ETL showed a maximum efficiency of 18.97 %, and PSC using spin coated SnO₂ showed a maximum efficiency of 18.46 %. This is because the short circuit current (Jsc) of PSC using the ALD SnO₂ layer was 0.75 mA/cm² higher than that of the spin coated SnO₂. This result can be attributed to the fact that the electron transfer distance from the perovskite is constant due to the thickness uniformity of ALD SnO₂. Therefore ALD SnO₂ is a candidate as a ETL for use in PSC vacuum deposition.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.943-946
• /
• 2001

In this study, We have investigated degradation effects of blue organic electroluminescence devices that was consisted of TPD(N,N'-dyphenyl-N-N\`-bis(3-methyphenyl) as hole transport layer and Butyl-PBD (2- (4-Biphenylyl)-5-(4-tert-butylphenyl)-1,3,4-oxadiazole)-as emission layer and electron transport layer. We have studied characteristics of brightness and current density about blue OEL that was degradated layer. Two kinds of samples that were fabricated each continuous and non-continuous method was used.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.155-155
• /
• 2010

We have investigated organic light-emitting devices by doping phosphorescent orange and fluorescent blue emitters into the separate layers of single host. The electroluminescence spectra and current efficiency were strongly dependent on the location of each doped layers. The luminance-voltage (L-V) characteristics of the device2 (ITO/Hole Transport Layer/Orange Phosphorescent emissive layer/Blue Fluorescent emissive layer/Electron Transport Layer/liF/Al) showed the maximum current efficiency of 19.5 cd/A.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.710-713
• /
• 2002

In order to improve the power efficiency of multi-layer organic light emitting diodes (OLEDs), electron injection into ETL(electron transport layer) from cathode at the interface between ETL and cathode was enhanced by interposing a proper electron injection layer at the interface. The HTL(hole transport layer) and ETL materials used were N, N'diphenyl- N, N' - bis(3-methylphenyl-1, 1'- biphenyl - 4, 4 'diamine (TPD) and tris (8-hydroxyquinoline) aluminum ($Alq_3$) respectively. Cathodes using co-evaporated Al-CsF, Al-KF, and Al-NaF composites are adopted to enhance the electrical and optical properties of OLEDs. OLEDs with alkaline metal-doped cathode show a luminance of as high as 35,000 cd/$m^2$, and external quantum efficiency about 1.35 %. In addition, they show higher power efficiency at all bias conditions and good reproducibility.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.3
• /
• pp.151-155
• /
• 2014

We have developed quantum dot light emitting diodes (QD-LEDs) using a InP/ZnSe/ZnS multi-shell QD emission layer. The hybrid structure of organic hole transport layer/QD/organic electron transport layer was used for fabricating QD-LEDs. Poly(4-butylphenyl-diphenyl-amine) (poly-TPD) and tris[2,4,6-trimethyl-3-(pyridin-3-yl)phenyl]borane (3TPYMB) molecules were used as hole-transporting and electron-transporting layers, respectively. The emission, current efficiency, and driving characteristics of QD-LEDs with 50, 65 nm thick 3TPYMB layers were investigated. The QD-LED with a 50 nm thick 3TPYMB layer exhibited a maximum current efficiency of 1.3 cd/A.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.28 no.9
• /
• pp.367-372
• /
• 2016

Gas diffusion layer (GDL) of PEMFCs plays a role that it diffuses the reactant gases to the catalyst layer on the membrane and discharge water from the catalyst layer to the channel. Physical parameters related to the mass transport of GDL are mostly from the uncompressed GDLs while actual GDLs in the assembled stacks are compressed. In this study, the relation of compression and strain of GDLs with various Polytetrafluoroethylene (PTFE) loading is measured experimentally and In-plane gas permeability is measured at the condition that the GDLs are in compressive strain. The gas permeability decreased with the loading of PTFE and the presentation of gas permeability under compressive stain is expected to improve the accuracy of modeling work of mass transport in the GDL.

• Electrical & Electronic Materials
• /
• v.7 no.5
• /
• pp.409-416
• /
• 1994

A double layered photoreceptor using phthalocyanine dye was made by dip-coating method. The under cutting layer(UCL) was coated with A1$\_$2/O$\_$3/ or polyamide, and the charge generation layer(CGL) was formed by .tau.-type metal-free phthalocyanine. The oxadiazole was used as a charge transport layer(CTL) and polycarbonate and poly(vinyl butyral) was employed as a host polymer. The .tau.-H$\_$2/Pc had an absorption peak around 780nm, which coincided with the emitting wavelengths of GaAlAs diode lasers. Maximum charge acceptance of CTL that gives thickness of 12.mu.m was -900V by corona charge of -6.0kV. In photo-induced discharge measurements, residual potential was less than -20V and sufficient for ordinary use, and sample films using of poly(vinyl butyral) was showed good charge retention. In printing test, drum that was employed polycarbonate as a host polymer showed the good print quality.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.46-47
• /
• 2008

Organic light-emitting diode is quick response speed, low power consumption and the self-interest has many advantages, such as insanity. So, organic light-emitting diode mechanism of light-emitting diode in order to more clearly understand the changes in the thickness of emitting materials for OLED characteristics of the simulation. emitting layer to a thickness of 10 [nm] ~ 100 [nm] changed the experiment, and hole transport layer 190 [nm] as a fixed. and emitting layer 10 [nm] ~ 100 [nm] to change the simulation results. Changes in the thickness of emitting layer gradually increased. depending on the emitting was 20 [nm] in the high 441 [lm / W] shows. and was gradually reduced. emitting layer 190 [nm] when fixed, hole transport layer, depending on changes in the thickness of 70 [nm] in the efficiency maximum value of 477 [lm / W], and was gradually reduced.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.534-537
• /
• 2002

We have studied conduction mechanism that is interpreted in terms of space charge limited current (SCLC) region and tunneling region. The OLEDs are based on the molecular compounds, N,N'-diphenyl-N,N'-bis(3-methylphenyl)-1,1'-biphenyl-4,4'-diamine (TPD) as a hole transport, tris (8- hydroxyquinolinoline) aluminum(III) $(Alq_3)$ as an electron injection and transport and emitting later, copper phthalocyanine (CuPc) and poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) and poly(vinylcarbazole) (PVK) as a buffer layer respectively. Al was used as cathode. We manufactured reference structure that has in ITO/TPD/$Alq_3$/Al. Buffer layer effects were compared to reference structure. And we have analyzed out luminance efficiency-voltage characteristics in ITO/Buffer layer/TPD/$Alq_3$/Al with buffer-layer materials.

• Journal of the Microelectronics and Packaging Society
• /
• v.14 no.4
• /
• pp.37-42
• /
• 2007

We fabricated the polymer light emitting diodes (PLEDs) with ITO/PEDOT:PSS/PVK/PFO:MEH-PPV/LiF/Al structures. The effect of the thickness of PEDOT:PSS hole injection layer(HIL) on the electrical and optical properties of PLEDs was investigated. In addition, PVK hole transport layer(HTL) was introduced in the PLED device, and compared the properties of the PLEDS with and without PVX layer. All organic film layers were prepared by the spin coating method on the plasma treated ITO/glass substrates. As the thickness of PEDOT:PSS film layer decreased from about 80 nm to 50 nm, the luminance of PLED device increased from $220cd/m^2$에서 $450cd/m^2$. This may be ascribed to the increased transportation efficiency of the holes into the emission layer of PLED. The maximum current density and luminance were obtained fir the PLED device with PVX hole transport layer, showing that the current density and luminance were $268mA/cm^2\;and\;540cd/m^2$ at 12V, respectively. This values were improved by about 14% and 22% in current density and luminance compared with the PLED device without PVK layer.