• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.3210-3212
• /
• 2000

We designed and manufactured 300MHz NMR RF Transceiver. NMR system is composed of NMR Spectrometer, Superconductive Magnet and Pulse Programmer, GUI. NMR RF Transceiver is composed of transmitter, receiver, frequency synthesizer. T/R switch, main power amp., RF coil. To phase modulation, transmitter is composed of mixer, splitter and combiner et al. To weak signal detection, receiver is composed of pre-amp., filter, mixer et al. Each module is manufactured PCB. And installed NMR system to detect chemical component of specimen. In result, we can get the information of specimen.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.11
• /
• pp.2431-2436
• /
• 2012

This paper is implemented simple visible light communication system by combining the communications through LED lighting. It uses a variable PD sensor to the receiver and 1~12 the LED light-emitting device to the transmitter to realize LED visible light communication. Initial distance value of the developed transmission and receiver is more than 0~1.5m for LED visible light communication, the overall system transmission rate is organized with thousands kbps variability visible light media transmission system. It was measured the performance experiment during lens wearing or not wearing in order to increase the overall efficiency of the LED module, configures the LED and PD to existing PC module for the performance analysis of the implemented research, experiments the maximum communication distance of the transmitter/receiver according to LED count and the transmission rate, check about application methods and the possibility.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.8 s.111
• /
• pp.767-772
• /
• 2006

The receiver of this paper is Dual-band monopulse type for prototype of tracking radar. Localization of radar technology is an issue of SamsungThales and go into development. Dual-band radar in comparison with Single-band radar requires higher cost and power consumption but there are many advantages of dealing with jamming, detection range, image signal rejection, cloud-rain influence, clutter, resolution. The receiver is comprised of X-band RF head module, Ka-band RF head module and common IF module. Each signal of X-band and Ka-band is selected by the switch in If module. Phase shifter in IF module of local stage controls the phase of sum, azimuth, elevation channel. In the test result, gain is $40{\pm}3 dB$, isolation of transmitter/receiver is 39 dBc, dynamic range is 110 dB and noise figure of each channel is 4.5dB and 6.9dB.

• Journal of the Korean Magnetics Society
• /
• v.23 no.2
• /
• pp.68-76
• /
• 2013

Currently, wireless power transmission technology based on magnetic induction was employed in battery charger for smart phone application. The system consists of wireless power transmitter in base station and receiver in smart phone. Size and thickness of receiver was strictly limited in the newest smart phone. In order to achieve high efficiency of a tiny small wireless power receiver module, sub-millimeter thick electromagnetic wave shielding sheet having high permeability and Q was essential component. It was found that magnetic field from transmitter to receiver can be intensified by sufficient shielding cause to minimize leakage magnetic flux by those magnetic properties. This leads to high efficiency of wireless power transmission and protects crucial integrated circuit of main board from electromagnetic noise. The important soft magnetic materials were introduced and summarized for the current small-power wireless power charger and NFC application and mid-power home appliance and high-power automotive application in the near future.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.3
• /
• pp.389-398
• /
• 2011

In this paper, the design and fabrication of a transmit/receive(T/R) module for Ka-band phased array radar is presented. A 5bit digital phase shifter and digital attenuator were used in common for both transmitter and receiver considering unique Ka-band characteristic. The circulator was excluded in the T/R module and was placed outside T/R module. The transmitting power per element antenna is designed to be about 1 W and the noise figure is designed to be below 8 dB. The designed T/R module RF part has a compact size of $5\;mm{\times}4\;mm{\times}57\;mm$. In order to implement the T/R module, MMICs used in T/R module was separately assessed before assembly of the designed T/R module. The transmitter of the fabricated T/R module shows about 1 W at 5 dBm unit module input power and the receiver shows a gain of about 20 dB and a noise figure of below 8 dB as expected in the design stage.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.1
• /
• pp.17-22
• /
• 2009

A switch or circulator is used for distinguishing between the paths of transmitter and receiver in TDD systems. If the isolation between Tx and Rx paths is low in TDD systems, the output signal of the ransmitter acts as an interferer to the receiver even if the transceiver operates on the receiver mode. In this paper we propose a method to get high isolation characteristics between transmitting and receiving paths in TDD systems. We implement the module with a proposed improving method to verify the effect of the isolation improvement and the experimental results are presented. The isolation improvement of above 44.8 dB over the frequency bandwidth of 30 MHz is obtained from the implemented isolation improvement module.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.10A
• /
• pp.796-806
• /
• 2009

This paper presents the method of emergency warning system operation based on T-DMB and the design of T-DMB AEAS receiver model. The proposed receiver model compares the geographical location of emergency with the location of DMB transmitting station from T-DMB broadcasting signal and classifies the receiver location into alert region, neighboring region and non-alert region and transmits the emergency alert message according to each region. The geographical location of emergency can be obtained from FIG 5/2 EWS data field for AEAS message and the location of DMB transmitting station can be estimated from either the latitude and the longitude in main identifier and sub identifier in FIG 0/22 data filed for TII(Transmitter Identification Information) or TII distribution database. In our experiment, we implemented the proposed receiver model with display section, storage section, DMB module for receiving broadcasting signal and control section and performed test emergency alert broadcasting using T-DMB signal generator.

• Journal of Industrial Technology
• /
• v.27 no.B
• /
• pp.97-101
• /
• 2007

We have developed a Edge Position Controller (EPC) using a ultrasonic sensor and applied to a fabric machine as a web guide system. Hardware devices composed of a ultrasonic transmitter-receiver sensor module and microprocessor-based sensor signal processing system are developed to realize the proposed system. We evaluated the control characteristics of the EPC and the performance of the system was good enough to apply the actual system.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.1
• /
• pp.140-146
• /
• 2018

Recently, VLC(Visible Light Communication) fusing with LED(Light Emitting Diode) used in indoor lighting and wireless communication technology has attracted attention. However, the VLC can communicate only within the coverage to measure the optical signal and the communication disconnection phenomenon is occur in the NLoS(Non-Line-of-Sight) area. In this paper, we propose VLC relay module to extend the coverage of VLC and improve the communication disconnection phenomenon in NLoS area. The proposed VLC relay module transmits the packet received from the transmitter to the VLC relay module and receiver. The experiment was carried out by installing one VLC transmitter and three VLC relay modules, communication coverage expansion and the improvement of communication disconnection phenomenon in the NLoS were confirmed by the increase of the VLC relay module. Also, we confirmed that the optical signal measurement performance is improved 2.4 times by using the dual sampling method.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.4
• /
• pp.295-301
• /
• 2011

A triple-band transceiver module for 2.3/2.5/3.5 GHz mobile WiMAX, IEEE 802.16e, applications is introduced. The suggested transceiver module consists of RFIC, reconfigurable/multi-resonance MIMO antenna, embedded PCB, mobile WiMAX base band, memory and channel selection front-end module. The RFIC is fabricated in $0.13{\mu}m$ RF CMOS process and has 3.5 dB noise figure(NF) of receiver and 1 dBm maximum power of transmitter with 68-pin QFN package, $8{\times}8\;mm^2$ area. The area reduction of transceiver module is achieved by using embedded PCB which decreases area by 9% of the area of transceiver module with normal PCB. The developed triple-band mobile WiMAX transceiver module is tested by performing radio conformance test(RCT) and measuring carrier to interference plus noise ratio (CINR) and received signal strength indication (RSSI) in each 2.3/2.5/3.5 GHz frequency.