• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.156-157
• /
• 2006

To improve mean-life and reliability of power cable in this study, we have investigated chemical properties showing by changing the content of Carbon nanotube(CNT) that is semiconductive additives for underground power transmission. Specimens were made of sheet form with the three of existing resins and the five of specimens for measurement. Chemical properties of specimens was measured by FT-ATR (Fourier Transform Attenuated Total Reflectance). The condition of specimens was a solid sheet. We could observe functional group (C=O, carbonyl group) of specimens through FT-ATR. From these experimental result, the concentration of functional group (C=O) was high according to increasing the content of Carbon nanotube. We could know CNT/EEA was excellent more than other specimens from above experimental results.

• Journal of the Korean Ceramic Society
• /
• v.18 no.4
• /
• pp.219-228
• /
• 1981

To clarify influences of silicious raw materials on mineralogcal and petrological properties in clinkering process clay, shale, quartzite, sand and coal ash have been used as silicious raw materials. The tests on thermal properties, reactivity and burnability of raw mixtures which have different silicious raw materials respectively have been made by means of X-ray diffractometry, differential thermal analysis, optical microscopy and transmission electron microscopy. Limestone contains coarse crystalline grains which show 0.1-1.0mm and its decarbonation temperature is 86$0^{\circ}C$. Reaction temperatures among raw mixtures have been determined by X-ray diffractometry and their results are as follows; clay minerals under 1, 00$0^{\circ}C$, mica group, 100$0^{\circ}C$-110$0^{\circ}C$, feldspar group, 1, 10$0^{\circ}C$-1, 20$0^{\circ}C$ and quartz 1, 20$0^{\circ}C$-1, 30$0^{\circ}C$. Burnabilities of raw mixtures of different temperatures have been found that they mainly depend upon their mineral contents in silicious raw materials and their order is as follows; $clay\geq shale\gg quartzite \geq sand$.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.973-976
• /
• 2006

In this paper, the inorganic multi-layer encapsulation of thin film was newly adopted to protect the organic layer from moisture and oxygen. Using the electron beam, Sputter, inorganic multi-layer thin-film encapsulation was deposited onto the Ethylene Terephthalate(PET) and their interface properties between inorganic and organic layer were investigated. In this investigation, the SiON $SiO_2$ and parylene layer showed the most suitable properties. Under these conditions, the water vapor transmission rate (WVTR) for PET can be reduced from level of $0.57g/m^2/day$ (bare substrate) to $1^{\ast}10^{-5}g/m^2/day$ after application of a SiON and $SiO_2$ layer. These results indicate that the $PET/SiO_2/SiON/Parylene$ barrier coatings have high potential for flexible organic light-emitting diode(OLED) applications.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.783-786
• /
• 2003

Thin films of vanadium oxide(VOx) have been deposited by r.f. magnetron sputtering from $V_2O_5$ target in gas mixture of argon and oxygen. The oxygen/(oxygen+argon) partial pressure ratio of 0% and 8% is adopted. Crystal structure and optical properties of films sputter-deposited under different oxygen gas pressures and in situ annealed in vacuum at $400^{\circ}C$ for 1h and 4h are characterized through XRD and optical absorption measurements. The films as-deposited are amorphous, but $0%O_2$ films annealed for time longer than 4h and $8%O_2$ films annealed for time longer than 1h are polycrystalline. The optical transmission of the films annealed in vacuum decreases considerably than the as-deposited films and the optical absorption of all the films increases rapidly at wavelength shorter than about 550nm. Indirect and direct optical band gaps were decreased with increasing the annealing time.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.330-333
• /
• 2002

The substrate temperature is an important parameter in thin film deposition process. In this paper the effects of the substrate temperature on the properties of CuIn0.75Ga0.25Se2(CIGS) thin films are reported. Structure, surface morphology and optical properties of CIGS thin films deposited at various substrate temperatures have been investigated using a number of analysis techniques. X-ray diffraction (XRD) analysis shows that CIGS films exhibit a strong <112> preferred orientation. As expected, at higher substrate temperatures the films displayed a higher degree of crystallinity. The <112> peak was also enhanced and other CIGS peaks appeared simultaneously These results were supported by experimental work using Raman spectroscopy. The Raman spectra of the as-grown CIGS thin films show only the Al mode peak. The intensity of this peak was enhanced at higher deposition temperatures. Scanning electron microscopy (SEM) results revealed very small grains in films fabricated at 48$0^{\circ}C$ substrate temperature. When the substrate temperature was increased the average grain size also increased together with a reduction in the number and size of the voids. The deposition temperature also had a significant influence on the transmission spectra.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.10
• /
• pp.883-888
• /
• 2007

Investigation of improving the properties of UV detector which uses the wide bandgap of ZnO are under active progress. The present study focused on the design and fabrication of i-ZnO/p-inversion $layer/n^--Si$ Epi. which is characterized with very thin p-type inversion layer for UV detectors. The i-ZnO thin film for achieving p-inversion layer which was grown by RF sputtering at $450^{\circ}C$ and then annealed at $400^{\circ}C$ in $O_2$ gas for 20 min shows good intrinsic properties. High (0002) peak intensity of the i-ZnO film is shown on XRD spectrum and it is confirmed by XPS analysis that the ratio of Zn : O of the i-ZnO film is nearly 1 : 1. Measurement shows high transmission of 79.5 % in UV range (< 400 nm) for the i-ZnO film. Measurement of $V_r-I_{ph}$ shows high UV photo-current of 1.2 mA under the reverse bias of 30 V.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.6
• /
• pp.791-796
• /
• 2007

When 2 sets of PID controllers are coupled directly each other to configure a closed control loop on behalf of coupling a controller and a plant. the behaviors or this exclusive loop system are expected to be unique in inherent system responses. If its properties be disclosed and generalized well in advance, it is possible for us to use the results for the purpose of fault detection and performance monitoring between control stations from the stage of system design. particularly in such cases as cascade control systems. In this paper. general properties of the proposed system are analyzed firstly to check whether it is controllable and how its steady responses would be. To simplify calculation, the analysis has been performed based on the transfer equation derived from a modelled case which consists of 2 PI controllers and signal converters between them. including time delay element and first-lag element to consider the situation of signal transmission. The results acquired from simulation are suggested to show how it works actually.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.73-78
• /
• 2008

The paper presents the characteristics of mechanical properties within the heat affected zone (HAZ) of dissimilar metal weld between SA508 Gr.1a and F316 stainless steel (SS) with Alloy 82/182 filler metal. Tensile tests were performed using small-size specimens taken from the HAZ regions close to both fusion lines of weld, and the micro-structures were examined using optical microscope (OM) and transmission microscope (TEM). The results showed that significant gradients of the yield stress (YS), ultimate tensile stress (UTS), and elongations were observed within the HAZ of SA508 Gr.1a. This was attributed to the different microstructures within the HAZ. In the HAZ of F316 SS, however, the welding effect dominated the YS and elongation rather than UTS, and TEM micrographs conformed the strengthening in the HAZ of F316 SS was associated with a dislocation-induced strain hardening.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.315.2-315.2
• /
• 2014

Pt-functionalized ZnS nanowires were synthesized on Au-deposited c-plane sapphire substrates by thermal evaporation of ZnS powders followed by wet Pt coating and annealing. The $NO_2$ gas sensing properties of multiple-networked Pt-functionalized ZnS nanowire sensors were examined. Scanning electron microscopy showed the nanowires with diameters of 20-80 nm. Transmission electron microscopy and X-ray diffraction showed that the nanowires were wurtzite-structured ZnS single crystals. The Pt-functionalized ZnS nanowire sensors showed enhanced sensing performance to $NO_2$ gas at $150^{\circ}C$ compared to pristine ZnS nanowire sensors. Pristine and Pt-functionalized ZnS nanowire sensors showed responses of 140-211% and 207-488%, respectively, to 1-5 ppm $NO_2$, which are better than or comparable to those of many oxide semiconductor sensors. In addition, the underlying mechanism of the enhancement of the sensing properties of ZnS nanowires by Pt functionalization is discussed.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.9
• /
• pp.455-458
• /
• 2004

In this paper, we investigated impurities content and physical properties showing by changing the content of carbon black that is semiconductive materials for underground power transmission. Specimens were made of sheet form with the three of existing resins and the nine of specimens for measurement. Impurities content of specimens was measured by ICP-AES (Inductively Coupled Plasma Atomic Emission Spectrometer), and density of specimens were measured by density meter And then specific heat (Cp) was measured by DSC (Differential Scanning Calorimetry). A ranges of measurement temperature were from $0^{\circ}[C]$ to $200^{\circ}[C]$, and heating temperature was $4^{\circ}[C/min]$. Impurities content was highly measured according to increasing the content of carbon black from this experimental result, also density was increased according to these properties. Especially impurities content values of the Al and A2 of existing resins were measured more than 4000［ppm］. Specific heat from the DSC results was decreased according to increasing the content of carbon black. Because ionic impurities of carbon black having Fe, Co, Mn, Al and Zn are rapidly passed kinetic energy increasing the number of times breaking during the unit time with the near particles according to increasing vibration of particles by the applied heat energy.