• Journal of the Korean Electrochemical Society
• /
• v.20 no.1
• /
• pp.7-12
• /
• 2017

Using a precursor of $LiNi_{0.6}Co_{0.2}Mn_{0.2}O_2$ as a starting material, a surface-modified cathode material was obtained by coating with KCl, where the added KCl reduces residual Li compounds such as $Li_2CO_3$ and LiOH, on the surface. The resulting electrochemical properties were investigated. The amounts of $Li_2CO_3$ and LiOH decreased from 8,464 ppm to 1,639 ppm and from 8,088 ppm to 6,287 ppm, respectively, with 1 wt% KCl added $LiNi_{0.6}Co_{0.2}Mn_{0.2}O_2$ that had been calcined at $800^{\circ}C$. X-ray diffraction results revealed that 1 wt% of KCl added $LiNi_{0.6}Co_{0.2}Mn_{0.2}O_2$ did not affect the parent structure but enhanced the development of hexagonal crystallites. Additionally, the charge transfer resistance ($R_{ct}$) decreased dramatically from $225{\Omega}$ to $99{\Omega}$, and the discharge capacity increased to 182.73mAh/g. Using atomic force microscopy, we observed that the surface area decreased by half because of the exothermic heat released by the Li residues. The reduced surface area protects the cathode material from reacting with the electrolyte and hinders the development of a solid electrolyte interphase (SEI) film on the surface of the oxide particles. Finally, we found that the introduction of KCl into $LiNi_{0.6}Co_{0.2}Mn_{0.2}O_2$ is a very effective method of enhancing the electrochemical properties of this active material by reducing the residual Li. To the best of our knowledge, this report is the first to demonstrate this phenomenon.

• Journal of Plant Biotechnology
• /
• v.45 no.3
• /
• pp.171-182
• /
• 2018

Papaya (Carica papaya L.) is one of the crops widely planted in tropical and subtropical areas. The papaya fruit has low calories and are plentiful in vitamins A and C and in minerals. A major problem in papaya production is a plant disease caused by the papaya ringspot virus (PRSV). The first PRSV-resistant GM papaya expressing a PRSV coat protein gene was developed by USA scientists in 1992. The first commercial GM papaya cultivars derived from the event was approved by the US government in 1997. Development of transgenic papayas has been focused on vaccine production and limited agricultural traits, including insect and pathogen resistance, long shelf life, and aluminum and herbicide tolerance. Approximately 17 countries, including the USA and China, produced transgenic papayas and/or commercialized them, which provoked studies on biosafety assessment and development of GM-detection technologies. For the biosafety assessment of potential effects on human health, effects of long-term feeding to model animals have been studied in terms of toxicity and allergenicity. Studies on environmental safety assessment include influence on soil-microbial biodiversity and transfer to soil bacteria of GM selection markers. Many countries, such as Korea, the European Union, and Japan, that have strict regulations for GM crops have serious concerns about unintended introduction of GM cultivars and food commodities using unauthorized GM crops. Transgene- and/or GM event-specific molecular markers and technologies for genomics-based detection of unauthorized GM papaya have been developed and have resulted in the robust detection of GM papayas.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.10-10
• /
• 2017

Rice consumption has been continuously decreasing as the eating habits of Koreans have become westernized and diversified. The per capita annual rice consumption in Korea has dropped sharply from 136.4 kg in 1970 to 61.9 kg in 2016. The Korean government, therefore, has been trying to promote rice consumption by invigorating the processed food industry using rice flour. To facilitate the market for processed rice foods, it is essential to develop proper milling technology in terms of flour particle size and damaged starch content to produce high quality rice flour at competitive cost. Dry milling and wet milling are the two major processes used to produce rice flour. Although the dry milling process is relatively simple with a lower production cost, damaged starch content increases because of the high grain hardness of rice. In wet milling, the quality of rice flour is improved by reducing flour particle size as well as damaged starch content through soaking procedures. However, the production costs are high because of the additional expenses associated with the disposal of waste water, sterilization and drying of the wet flour. Recently developed technologies such as jet milling and cryogenic milling also require expensive investment and production. Therefore, developing new rice cultivars with dry milling adaptability as well as good processing properties is an important goal of rice breeding in Korea. 'Suweon 542' is a floury endosperm mutant line derived from sodium azide treatment on a high-yield, early maturing, and non-glutinous japonica rice cultivar, 'Namil'. Compared with the wild type, after dry milling process, the grain hardness of 'Suweon 542' was significantly lower because of its round and loosely packed starch granules. Also, the flour of 'Suweon 542' had significantly smaller particles and less damaged starch than 'Namil' and other rice cultivars and its particle size distribution was similar to a commercial wheat cultivar. Recently, through collaborations with nine universities and food companies, a total of 21 kinds of processed prototypes, using the dry milling flour of 'Suweon 542', were evaluated. In the production of major rice processing products, there was no significant quality difference between the flours prepared by wet milling and dry milling. Although the amount of water added to the dough was slightly increased, it was confirmed that the recipe applying the wet flour could be used without significant change. To efficiently transfer the floury endosperm characteristics of 'Suweon 542' to other commercial rice cultivars, it is essential to develop DNA marker tightly linked to the target gene. Association analysis using 70 genome-wide SSR markers and 94 F2 plants derived from 'Suweon 542'/'Milyang 23' showed that markers on chromosome 5 explained a large portion of the variation in floury grains percentage (FGP). Further analysis with an increased number of SSR markers revealed that the floury endosperm of 'Suweon 542' was directed by a major recessive locus, flo7(t), located in the 19.33-19.86 Mbp region of chromosome 5, with RM18639 explaining 92.2% of FGP variation in the F2 population. Through further physical mapping, a co-segregate and co-dominant DNA marker with the locus, flo7(t) was successfully developed, by which, thereby, breeding efficiency of rice cultivars having proper dry milling adaptability with high yield potential or useful functional materials would be improved. 'Suweon 542' maintained the early maturity of the wild type, Namil, which can be used in rice-wheat double cropping systems in Korea not only for improved arable land but also for sharing flour production facilities. In addition to the high susceptibility against major rice diseases, nevertheless, another possible drawback of 'Suweon 542' is the high rate of viviparous under prolonged rainfall during the harvesting season. To overcome susceptibility and vivipary of 'Suweon 542', the progeny lines, derived from the crosses 'Suweon 542' and 'Jopyeong', an early maturing rice cultivar with multiple resistance against rice blast, bacterial blight, and rice strip virus, and 'Heugjinju', a anthocyanin pigment containing black rice cultivar, were intensively evaluated. As the outputs, three dry milling suitable rice elite lines, 'Jeonju614', 'Jeonju615', and 'Jeonju616' were developed.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.05a
• /
• pp.463-466
• /
• 2017

The purpose of this paper is to develop a module capable of all-directional driving different from conventional wheeled robots, and to solve the problems of the conventional mobile robot with side driving performance degradation, It is possible to overcome the disadvantages such as an increase in the time required for the unnecessary driving. The all - direction spherical wheel drive module for driving a ball - balancing robot is required to develop a power transfer mechanism and a driving algorithm for driving the robot in all directions using three rotor casters. 3DoF (Axis) A driver with built-in forward motion algorithm is embedded in the module and a driving motor module with 3DoF (axis) for driving direction and speed is installed. The movement mechanism depends on the sum of the rotation vectors of the respective driving wheels. It is possible to create various movement directions depending on the rotation and the vector sum of two or three drive wheels. It is possible to move in different directions according to the rotation vector field of each driving wheel. When a more innovative all-round spherical wheel drive module for forward movement is developed, it can be used in the driving part of the mobile robot to improve the performance of the robot more technically, and through the forward-direction robot platform with the drive module Conventional wheeled robots can overcome the disadvantage that the continuous straightening performance is lowered due to resistance to various environments. Therefore, it is necessary to use a full-direction driving function as well as a cleaning robot and a mobile robot applicable in the Americas and Europe It will be an essential technology for guide robots, boarding robots, mobile means, etc., and will contribute to the expansion of the intelligent service robot market and future automobile market.

• Journal of the Korean Electrochemical Society
• /
• v.17 no.4
• /
• pp.222-228
• /
• 2014

Ni-rich system $Li[Ni_{1-x-y}Co_xMn_y]O_2$ of lithium secondary battery cathode material keep a high discharge capacity. However, by the Ni content increases, there is a problem that the electrochemical properties and stability of the structure are reduced. In order to solve these problems, research for positive ion doping is performed. The one of the cathode material, barium-doped $Li[Ni_{0.6-x}Ba_xCo_{0.1}Mn_{0.3}]O_2$ (x=0.01), was synthesized by the precursor, $Ni_{0.6}Co_{0.1}Mn_{0.3}(OH)_2$, from the co-precipitation method. The barium doped materials have studied the structural and electrochemical properties. The analysis of structural properties, results of X-ray diffraction analysis, and those results confirmed the change of the lattice from the binding energy in the structure by barium doping. Increased stability of the layered structure was observed by $I_{(006)}+I_{(102)}/I_{(101)}$(R-factor) ratio decrease. we expected that the electrochemical characteristics are improved. 23 mAh/g discharge capacity of barium-doped $Li[Ni_{0.6-x}Ba_xCo_{0.1}Mn_{0.3}]O_2$ (x=0.01) electrode is higher than discharge capacity of $Li[Ni_{0.6}Co_{0.1}Mn_{0.3}]O_2$ due to decrease overvoltage. And, through the structural stability was confirmed that improved the cycle characteristics. We caused a reduction in charge transfer resistance between the electrolyte and the electrode was confirmed that the C-rate characteristics are improved.

• Journal of Bio-Environment Control
• /
• v.28 no.3
• /
• pp.273-278
• /
• 2019

The multi-layer insulating curtains used in the experiment was produced in six combinations using non-woven fabric containing aerogel and compared and analyzed by measuring heat flux and heat perfusion rates due to weight, thickness and temperature changes. Using silica aerogel, which have recently been noted as new material insulation, this study tries to produce a new combination of multi-layer insulating curtains that can complement the shortcomings of the multi-layer insulating curtains currently in use and maintain and improve its warmth, and analyze the thermal properties. The heat flux means the amount of heat passing per unit time per unit area, and the higher the value, the more heat passing through the multi-layer insulating curtain, and it can be judged that the heat retention is low. The weight and thickness of multi-layer insulation curtains were found to be highly correlated with thermal insulation. In particular, insulation curtains combined with aerogel meltblown non-woven fabric had relatively higher thermal insulation than insulation curtains with the same number of insulation materials. However, the aerogel meltblown non-woven fabric is weak in light resistance and durability, and there is a problem that the production process and aerogel are scattering. In order to solve this problems, the combination of expanded aerogel non-woven fabric and hollow fiber non-woven fabric, which are relatively simple manufacturing processes and excellent warmth, are suitable for use in real farms.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.38 no.4
• /
• pp.253-259
• /
• 2018

A new barley (Hordeum vulgare L.) cultivar 'Mihan' having ruminant-palatable semi-smooth awn and good silage quality was developed at National Institute of Crop Science(NICS), RDA in 2016. This cultivar was derived from a cross of the 'SB00T2064' and 'Suwon385' in 2001. And its promising line showed high yielding through the preliminary yield trials(PYT) and advanced yield trials (AYT) in Iksan from 2012 to 2013. It was designated as the 'Iksan487'. 'Iksan487' was conducted to regional yield trials (RYT) in one upland field and five paddy fields around Korea for three years from 2014 to 2016. And it was released as the name of 'Mihan'. It has growth habit of IV, erect plant type, green leaf and semi-smooth awn. Its heading date was April 23 in the paddy field and maturing date was May 24. Plant height of 'Mihan' was 96cm. Mihan's spikes per $m^2$ was 665. It has better winter hardiness and resistance to BaYMV (Barley Yellow Mosaic Virus) than that of barley cultivar 'Youngyang'. The average dry matter of 'Mihan' was about $10.9ton\;ha^{-1}$ in paddy field. And average feed quality of 'Mihan' was 10.3% of crude protein content, 26.1% of ADF (Acid Detergent Fiber), 46.9 % of NDF (Neutral Detergent Fiber) and 68.2% of TDN (Total Digestible Nutrients). 'Mihan' had grade I of silage quality. This cultivar would be suitable for the area above the daily minimum average temperature of $-8^{\circ}C$ in January in Korean peninsula.

• Journal of the Korea Institute of Building Construction
• /
• v.22 no.6
• /
• pp.651-662
• /
• 2022

The electrochemical impedance spectroscopy(EIS) method was used to evaluate the concrete deterioration process related to chloride-induced steel corrosion with various corrosion levels(initiation, rust propagation and acceleration periods). The impressed current technique, with four total current levels of 0C, 13C, 65C and 130C, was used to accelerate steel corrosion in concrete cylinder samples with w/c ratio of 0.4, 0.5, and 0.6, immersed in a 0.5M NaCl solution. A series of EIS measurements was performed to monitor concrete deterioration during the accelerated corrosion test in this study. Some critical parameters of the equivalent circuit were obtained through the EIS analysis. It was observed that the charge transfer resistance(R_c) dropped sharply as the impressed current increased from 0C to 13C, indicating a value of approximately 10kΩcm². However, the sensitivity of R_c significantly decreased when the impressed current was further increased from 13C to 130C after corrosion of steel had been initiated. Meanwhile, the double-layer capacitance value(C_dl) linearly increased from 50×10^-6μF/cm² to 250×10^-6μF/cm² as the impressed current in creased from 0C to 130C. The results in this study showed that monitoring C_dl is an effective measurement parameter for evaluating the progress of internal concrete damages(de-bonding between steel and concrete, micro-cracks, and surface-breaking cracks) induced by steel corrosion. The findings of this study provide a fundamental basis for developing an embedded sensor and signal interpretation method for monitoring concrete deterioration due to steel corrosion at various corrosion levels.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.4 no.1
• /
• pp.119-127
• /
• 2002

This study was conducted to develop the heat exchanger by utilizing the heat energy of underground water(15℃), which might be used for cooling and heating system of the agricultural facilities. We developed the heat exchanger, parallel type plat fin tube made of Aluminum(Al 6063), which was named Aloo-Heat(No. of The registration design : 0247164, by Korean Intellectual property Office). The fin of exchanger was design of the granulated surface for minimizing fouling factor and dew forms, and also placed parallel to the tube in order to minimized the resistance of flows. 1. Aloo-heat was designed to have 0.03m for inside diameter, 0.036m for outside diameter of tube, 0.0012m for thickness of fin and 0.032m for length of plat fin. 2. t was also designed to have 1.5248m²/m for outside area of heat transfer, 0.0942m²/m for inside area contacting hot liquid, and the ratio (Ra) was 16.1869. 3. Efficiency of the fin was 93 percentage when fin length was 0.032m, and the fin thickness satisfied equation $\frac{h{\rho}}{k}$< 0.2 when it was 0.0012m. 4. According to the performance test of Aloo-heat, as the temperature and rate increased, the heating value also increased, heating value was 504kJ/h·m and 6,048kJ/h·m when it was 60℃, 10 𝑙/min and 80℃, 40 𝑙/min respectively. 5. The test of heating value was confident, because correlation value(R²) was 0.9898 for the temperature and 0.9721 for flow rate of hot liquid, respectively.

• Korean Journal of Animal Reproduction
• /
• v.21 no.2
• /
• pp.167-176
• /
• 1997

This study was carried out to evaluate the potential for preselection of transgenic embryos prior to transfer into recipient animals. In these experiments, I used a 3.2 kb transgene which contained the neomycin resistance gene (neo) and lac Z gene driven by the $\beta$ actin promoter (iacZ Ineo). Oocytes were aspirated from abattoir ovaries, matured in TCM-199 supplemented with 10% fetal bovine serum (FBS), 5 ${\mu}\textrm{g}$/ml LH, 0.5 ${\mu}\textrm{g}$/ml FSH, 100 unit/ml penicillin, and 100 ${\mu}\textrm{g}$/ml streptomycin for 22 to 24 hrs then inseminated with a sperm suspension of 1 X 10$^6$ sperm/ml containing 5 ${\mu}\textrm{g}$/ml of heparin. At 18-20 hrs after insemination, cumulus cells were removed by vortexing and pronuclei of centrifuged zygotes microinjected with the lacZ/neo construct (3 ng/$\mu$l). All cultures were carried out in CR1aa with transfected BRL monolayers containing 3 mg/ml BSA, 20 $\mu$/ml NEM amino acids and 40 $\mu$I/ml BME amino acids. To identify the appropriate concentration of G418 for selection, non-microinjected zygotes were cultured in the presence of 0, 50, 100 and 200 $\mu$g/ml of G418. After 8 days of culture in these treatments, 44/145 (30.3%), 13/150 (8. 7%), 1/151 (0.7%) and 0/134 (0.0%) devel-oped to the blastocyst stage in 0, 50, 100 and 200 $\mu$g/ml of G418, respectively. A total of 1,127 zygotes were microinjected and placed into culture (without G418) and subsequently 710 (63.0%) cleaved. At 48 hrs post-injection, embryos ($\geq$2-cell) were randomly assigned to control (medium alone) or G418 (100 ${\mu}\textrm{g}$/ml) treatments. A control culture of 740 non-microinjected embryos from the same replicates of embryos were also placed into control medium. After 8 days in culture, 54/343 (15.7%) and 22/367 (6.0 %) of the microinjected embryos developed to the blastocyst stage in control and G418 media, respectively. A total of 151/740 (27.2%) of the non-microinjected embryos placed in the control medium developed to the blastocyst stage. The blastocysts in the control treatment had a mean of 70.7 ${\pm}$ 4.7 cells of which 23.1 ${\pm}$ 2.6 (32.7%) stained for $\beta$-Gal activity. B1astocysts in the G418 treatment had a mean of 48.8${\pm}$7.5 cells of which 40.3 ${\pm}$ 4.1 (82.6%) stained for $\beta$-Gal ac tivity (P<0.05). In the control treatment 26 of 30 (87.0%) blastocysts had some cells with $\beta$-Gal activity while all of the blastocysts in the G418 treatment had some cell with $\beta$-Gal ac tivity (P<0.05). However, ICM colonies in either control or G418 treatments were not expressed any epiblast cell except of trophetoderm celIs. The $\beta$-actin promoter/lacZ gene may not be e expression or silence expression in epiblast cells These results clearly show an enrichment of blastocysts expressing the transgene in the majority of their cells after culture in the presence of G418. The exogeneous gene was not express a and silence in ICM colonies especiallly epiblast cells except of trophectederm cells. Even though the higher rate cell number expressed of exogeneous gene in the G418 treatments, a total cell number was decrease significantly (P<0.05) of which might be also drop of the establishment of ES like-cell colonies and production of transgenic animals. However, futher studies need to determine the viability of these selected embryos and the avability of production of transgenic offspring.