• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1638-1641
• /
• 2008

We have investigated the effectiveness of a gravure printing method for the fabrication of organic light-emitting diode (OLED) and Organic Thin Film Transistor (OTFT). Printing of the organic layers was performed with a small-scale gravure coating machine, while the metallic layers were vacuum-evaporated. Devices with gravure-printed layers are at least comparable with the spin-coated devices. Effects of the solvent formulation and surface energy mismatch between the organic layer materials on the printed patterns and device performance were discussed. We will present the initial design and experimental data of OTFT fabricated by roll-type soft contact transfer process.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.11a
• /
• pp.35-36
• /
• 2005

An ejector driven by a liquid is a fluid transfer equipment to be used under a poor suction condition, which means that there exists a possibility to occur a cavitation. It is a highly reliable device because it has no movable part in it, that is only a passive equipment. The ejector is an inevitably necessary one to overcome a poor pumping condition and to mix uniformly two fluids, however it has a low efficiency since it requires a pump for its operation. This study is for the development of a new-type liquid ejector with the application of a nozzle shape alteration, which maximize the suction performance of it. which provides the increased competition with the domestic industries. Also, the increased performance opens a new manufacturing method to use a commercial pipes for the production of an ejector, which is based on a trivial loss of a performance. However, this minor loss can be sufficiently compensated by the increased performance of a new-type ejector. Therefore, the developed ejector by this study can considerably reduce the manufacturing time and cost while its performance is largely increased.

• Journal of IKEEE
• /
• v.3 no.2 s.5
• /
• pp.161-167
• /
• 1999

3-input neuron-MOSFET inverters and 3-bit D/A converters using enhancement type device have been designed and fabricated by using standard 2-poly CMOS process. The voltage transfer curve and the noise margin of neuron-MOSFET inverters have been measured and characterized as the same method in normal CMOS inverters. From the theoretical calculation of the effects of coupling ratio on the voltage transfer curve and noise margin, we set up the design guideline for the gate oxide thickness and input gate layout in neuron-MOSFET inverters. BT using one of input gates as a control gate, we can design and fabricate the neuron-MOSFET D/A converter without offset voltage.

• Journal of the Korea Society of Computer and Information
• /
• v.17 no.7
• /
• pp.13-22
• /
• 2012

In this paper, we design and implement the architecture of the ubiquitous software robot platform (Sobot platform) based on Web 2.0. In order to provide a user with the personalized emotional service by transferring to any device without any time or geographical limitations, the software robot must be developed as a form of a platform based on the standardized data and structures. To verify the effectiveness and the feasibility of the proposed Sobot platform consisting of the terminal platform, the server platform, and the contents composer, we compose user-created emotional Sobot contents messages on heterogeneous platforms such as PC, a mobile phone, a PDA, and a web portal site and experiment a variety of Sobot transfer implementation between them.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.26 no.1
• /
• pp.32-37
• /
• 2014

The thermal contact resistance (TCR) is one of the important resistance components in cryogenic systems. Cryogenic measurement devices using a cryocooler can be affected by TCR because the device has to consist of several metal components that are in contact with each other for heat transfer to the specimen without a cryogen. Therefore, accurate measurement and understanding of TCR is necessary for the design of cryogenic measurement devices using a cryocooler. The TCR occurs at the interface between metals and it can be affected by variable factors, such as the roughness of the metal surface, the contact area and the contact pressure. In this study, we designed a TCR measurement system at variable temperature using a cryocooler as a heat sink. Copper was selected as a specimen in the experiment because it is widely used as a heat transfer medium in cryogenic measurement devices. We measured the TCR between Cu and Cu for various temperatures and contact pressures. The effect of the interfacial materials on the TCR was also investigated.

• Journal of the Optical Society of Korea
• /
• v.20 no.4
• /
• pp.470-475
• /
• 2016

In this paper, the effects of filter parameters on a supercontinuum-based all-optical thresholder are experimentally investigated. By tuning the filter parameters, the power transfer function and power transmission function are tailored. The experimental results show that a thresholder with short center wavelength has a better power function, and the slope in the middle level of the thresholder increases with increasing bandwidth. Through tuning the filter parameters, the thresholder can achieve a steplike power transfer function for optical thresholding, and a steplike power transmission function for optical self-switching. This makes the supercontinuum-based thresholder more flexible, and allows customization of performance to meet different demands in various applications.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1582-1584
• /
• 1996

The polycrystalline silicon thin film transistors (poly-Si TFT) are the most promising candidate for active matrix liquid crystal displays (AMLCD) for their high mobilities and current driving capabilities. The leakage current of the poly-Si TFT is much higher than that of the amorphous-Si TFT, thus larger storage capacitance is required which reduces the aperture ratio fur the pixel. The offset gated poly-Si TFTs have been widely investigated in order to reduce the leakage current. The conventional method for fabricating an offset device may require additional mask and photolithography process step, which is inapplicable for self-aligned source/drain ion implantation and rather cost inefficient. Due to mis-alignment, offset devices show asymmetric transfer characteristics as the source and drain are switched. We have proposed and fabricated a new offset poly-Si TFT by applying photoresist reflow process. The new method does not require an additional mask step and self-aligned ion implantation is applied, thus precise offset length can be defined and source/drain symmetric transfer characteristics are achieved.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.1096-1101
• /
• 2005

In this study, the experiment of thermal performance about closed-type hybrid cooling tower was conducted. A closed type cooling tower is a device similar to a general cooling tower, but with cooling tower replaced by a heat exchanger. The test section for this experiment has the process that the cooling water flows from top part of heat exchanger to bottom side in the inner side of tube, and spray water flows gravitational direction in the outer side of it. Air contacts of tube outer side are counterflow. The heat transfer pipe used in this experiment is a bare type tube having an outside diameter of 15.88mm. In this experiment, heat performances of the cooling tower are calculated such as overall heat transfer coefficient of between the process fluid and air, cooing capacity and pressure drop.

• Korean Journal of Materials Research
• /
• v.26 no.11
• /
• pp.635-643
• /
• 2016

Graphene has shown exceptional properties for high performance devices due to its high carrier mobility. Of particular interest is the potential use of graphene nanoribbons as field-effect transistors. Herein, we introduce a facile approach to the fabrication of graphene nanoribbon (GNR) arrays with ~200 nm width using nanoimprint lithography (NIL), which is a simple and robust method for patterning with high fidelity over a large area. To realize a 2D material-based device, we integrated the graphene nanoribbon arrays in field effect transistors (GNR-FETs) using conventional lithography and metallization on highly-doped $Si/SiO_2$ substrate. Consequently, we observed an enhancement of the performance of the GNR-transistors compared to that of the micro-ribbon graphene transistors. Besides this, using a transfer printing process on a flexible polymeric substrate, we demonstrated graphene-silicon junction structures that use CVD grown graphene as flexible electrodes for Si based transistors.

• The KIPS Transactions:PartA
• /
• v.8A no.2
• /
• pp.147-156
• /
• 2001

A high performance routing switch is an essential device to either the high performance parallel processing or communication networks that handle multimedia transfer systems such as VOD. The high performance routing chip called STC104 is a typical example in the technical aspect which has 32 bidirectional links of 100Mbps transfer sped. It has exploited new technologies, such as wormhole routing, interval labeling, and adaptive routing method. The high speed router has been applied into some parallel processing system as a single chip. However, its performance over the various interconnection networks with multiple routing chips has not been studied. In this paper, the strucrtures and characteristics of the STC104 have been investigated in order to evaluate the high speed router. Various topology of the STC104, such as meshes, torus, and N-cube are defined and constructed. Algorithms of packet transmission have been proposed based on the interval labeling and the group adaptive routing method implemented in the interconnected network. Multicast algorithms, which are often requited to the processor networks and broadcasting systems, modified from U-mesh and U-torus algorithms have also been proposed overcoming the problems of point-to-point communication.