• Korean Journal of Food Science and Technology
• /
• v.37 no.2
• /
• pp.183-188
• /
• 2005

Effects of co-solvent polarity, citric acid, pressure, temperature, run time, and co-solvent ratio on extraction of major flavonoids from Lonicera Flos were investigated using supercritical fluid $CO_{2}(SF-CO_{2})$. HPLC analysis revealed addition of pure methanol resulted in low extraction yield of major flavonoids, luteoloin (Lu), Quercetin (Qu), Apigenin (Ap). Under same condition, as co-solvent polarity increased, yields of major flavonoids increased gradually, At optimum co-solvent extraction condirion of 60% aqueous methanol (10%, v/v), yields of Lu, Qu, and Ap were 42.09, 28.18, and 3.49 mg/100 g, respectively. Addition of citric acid to 60% aqueous methanol gave higher, with addition of 1% citrie acid resulting in highest yields of 63.2 (Lu), 39.35 (Qu), and 5.79 (Ap) mg/100 g. Optimum extraction conditions of major flavonoids were 200 bar, $50^{\circ}C$, 60 min, and $CO_{2}$-methanol-water(20: 1.8: 1.2).

• Journal of the Korean Electrochemical Society
• /
• v.17 no.4
• /
• pp.222-228
• /
• 2014

Ni-rich system $Li[Ni_{1-x-y}Co_xMn_y]O_2$ of lithium secondary battery cathode material keep a high discharge capacity. However, by the Ni content increases, there is a problem that the electrochemical properties and stability of the structure are reduced. In order to solve these problems, research for positive ion doping is performed. The one of the cathode material, barium-doped $Li[Ni_{0.6-x}Ba_xCo_{0.1}Mn_{0.3}]O_2$ (x=0.01), was synthesized by the precursor, $Ni_{0.6}Co_{0.1}Mn_{0.3}(OH)_2$, from the co-precipitation method. The barium doped materials have studied the structural and electrochemical properties. The analysis of structural properties, results of X-ray diffraction analysis, and those results confirmed the change of the lattice from the binding energy in the structure by barium doping. Increased stability of the layered structure was observed by $I_{(006)}+I_{(102)}/I_{(101)}$(R-factor) ratio decrease. we expected that the electrochemical characteristics are improved. 23 mAh/g discharge capacity of barium-doped $Li[Ni_{0.6-x}Ba_xCo_{0.1}Mn_{0.3}]O_2$ (x=0.01) electrode is higher than discharge capacity of $Li[Ni_{0.6}Co_{0.1}Mn_{0.3}]O_2$ due to decrease overvoltage. And, through the structural stability was confirmed that improved the cycle characteristics. We caused a reduction in charge transfer resistance between the electrolyte and the electrode was confirmed that the C-rate characteristics are improved.

• Journal of Korean Society of Forest Science
• /
• v.99 no.4
• /
• pp.611-617
• /
• 2010

The current studies aim is to analyze the production cost of walnut tree cultivation and its object was targeted at walnut tree cultivating household region 163. The analysis is as follows. Our domestic walnut tree cultivating households averagely have cultivated about 0.7ha, and planting number per ha was averagely 204, and it showed that compared to the standard planting number (100), the plantation was done close planted. The most cultivar cultivated according to regions were Chungbuk region: sangchon 65.7%, Chungnam region: kwangduk 68.6%, Jeonbuk region: sangchon 98.0%, Gyeongbuk region: daeboo 61.2%. The production cost for cultivating walnuts can be classified into the followings; management cost(4436 thousand won/ha) such as manufacturing cost(292 thousand won/ha), intermediate material cost(3682 thousand won/ha), rent(103 thousand won/ha), employment cost(653 thousand won/ha) etc, and self-serviced expenses such as self-laboring cost(5,834 thousand won/ha), land security cost(490 thousand won/ha), fixed capital cost(834 thousand won/ha), circulating capital cost(234 thousand won/ha) etc. 11,820 thousand won were invested for the production cost of walnut and it made 11,586 thousand won/ha(rate of investment 72.3%) profit, and the net income was 4,196 thousand won/ha(net income rate 26.2%), showing high amount of income. The manufactured walnuts were marketed in Nong-hyup 39.8%, wholesalers 20.8%, dealers 19.8% and recently, as the amount of goods marketed directly to consumers themselves have increased, the income has reached up to 18.9%. At the basis of making most of idle soil, walnut tree's cultivated regions are fairly small, and due to the characteristics of sideline management, it has its limits in searching for production policy locally and promotion strategy of industries. Therefore, if the basic database can be established, subjected only to full-time cultivating households, then not only would the differences between the imported walnuts be reinforced, it would also be possible to transfer into the new and improved distribution system. Furthermore, through establishment of the database, it can be anticipated that it would contribute greatly in the increase of the household income.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.8 no.2
• /
• pp.86-96
• /
• 2006

Ecoclimap-1, a new complete surface parameter global database at a 1-km resolution, was previously presented. It is intended to be used to initialize the soil-vegetation- atmosphere transfer schemes in meteorological and climate models. Surface parameters in the Ecoclimap-1 database are provided in the form of a per-class value by an ecoclimatic base map from a simple merging of land cover and climate maps. The principal objective of this ecoclimatic map is to consider intra-class variability of life cycle that the usual land cover map cannot describe. Although the ecoclimatic map considering land cover and climate is used, the intra-class variability was still too high inside some classes. In this study, a new strategy is defined; the idea is to use the information contained in S10 NDVI SPOT/VEGETATION profiles to split a land cover into more homogeneous sub-classes. This utilizes an intra-class unsupervised sub-clustering methodology instead of simple merging. This study was performed to provide a new ecolimatic map over Northeast Asia in the framework of Ecoclimap-2 global database construction for surface parameters. We used the University of Maryland's 1km Global Land Cover Database (UMD) and a climate map to determine the initial number of clusters for intra-class sub-clustering. An unsupervised classification process using six years of NDVI profiles allows the discrimination of different behavior for each land cover class. We checked the spatial coherence of the classes and, if necessary, carried out an aggregation step of the clusters having a similar NDVI time series profile. From the mapping system, 29 ecosystems resulted for the study area. In terms of climate-related studies, this new ecosystem map may be useful as a base map to construct an Ecoclimap-2 database and to improve the surface climatology quality in the climate model.

• Restorative Dentistry and Endodontics
• /
• v.34 no.4
• /
• pp.324-332
• /
• 2009

The purpose of this study was to investigate the effect of rigidity of post core systems on stress distribution by the theoretical technique, finite element stress-analysis method. Three-dimensional finite element models simulating an endodontically treated maxillary central incisor restored with a zirconia ceramic crown were prepared and 1.5 mm ferrule height was provided. Each model contained cortical bone, trabecular bone, periodontal ligament, 4 mm apical root canal filling, and post-and-core. Six combinations of three parallel type post (zirconia ceramic, glass fiber, and stainless steel) and two core (Paracore and Tetric ceram) materials were evaluated, respectively. A 50 N static occlusal load was applied to the palatal surface of the crown with a $60^{\circ}$angle to the long axis of the tooth. The differences in stress transfer characteristics of the models were analyzed. von Mises stresses were chosen for presentation of results and maximum displacement and hydrostatic pressure were also calculated. An increase of the elastic modulus of the post material increased the stress, but shifted the maximum stress location from the dentin surface to the post material. Buccal side of cervical region (junction of core and crown) of the glass fiber post restored tooth was subjected to the highest stress concentration. Maximum von Mises stress in the remaining radicular tooth structure for low elastic modulus resin core (29.21 MPa) was slightly higher than that for high elastic modulus resin core (29.14 MPa) in case of glass fiber post. Maximum displacement of glass fiber post restored tooth was higher than that of zirconia ceramic or stainless steel post restored tooth.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.1-2
• /
• 2011

Hybrid rockets have lately attracted attention as a strong candidate of small, low cost, safe and reliable launch vehicles. A significant topic is that the first commercially sponsored space ship, SpaceShipOne vehicle chose a hybrid rocket. The main factors for the choice were safety of operation, system cost, quick turnaround, and thrust termination. In Japan, five universities including Hokkaido University and three private companies organized "Hybrid Rocket Research Group" from 1998 to 2002. Their main purpose was to downsize the cost and scale of rocket experiments. In 2002, UNISEC (University Space Engineering Consortium) and HASTIC (Hokkaido Aerospace Science and Technology Incubation Center) took over the educational and R&D rocket activities respectively and the research group dissolved. In 2008, JAXA/ISAS and eleven universities formed "Hybrid Rocket Research Working Group" as a subcommittee of the Steering Committee for Space Engineering in ISAS. Their goal is to demonstrate technical feasibility of lowcost and high frequency launches of nano/micro satellites into sun-synchronous orbits. Hybrid rockets use a combination of solid and liquid propellants. Usually the fuel is in a solid phase. A serious problem of hybrid rockets is the low regression rate of the solid fuel. In single port hybrids the low regression rate below 1 mm/s causes large L/D exceeding a hundred and small fuel loading ratio falling below 0.3. Multi-port hybrids are a typical solution to solve this problem. However, this solution is not the mainstream in Japan. Another approach is to use high regression rate fuels. For example, a fuel regression rate of 4 mm/s decreases L/D to around 10 and increases the loading ratio to around 0.75. Liquefying fuels such as paraffins are strong candidates for high regression fuels and subject of active research in Japan too. Nakagawa et al. in Tokai University employed EVA (Ethylene Vinyl Acetate) to modify viscosity of paraffin based fuels and investigated the effect of viscosity on regression rates. Wada et al. in Akita University employed LTP (Low melting ThermoPlastic) as another candidate of liquefying fuels and demonstrated high regression rates comparable to paraffin fuels. Hori et al. in JAXA/ISAS employed glycidylazide-poly(ethylene glycol) (GAP-PEG) copolymers as high regression rate fuels and modified the combustion characteristics by changing the PEG mixing ratio. Regression rate improvement by changing internal ballistics is another stream of research. The author proposed a new fuel configuration named "CAMUI" in 1998. CAMUI comes from an abbreviation of "cascaded multistage impinging-jet" meaning the distinctive flow field. A CAMUI type fuel grain consists of several cylindrical fuel blocks with two ports in axial direction. The port alignment shifts 90 degrees with each other to make jets out of ports impinge on the upstream end face of the downstream fuel block, resulting in intense heat transfer to the fuel. Yuasa et al. in Tokyo Metropolitan University employed swirling injection method and improved regression rates more than three times higher. However, regression rate distribution along the axis is not uniform due to the decay of the swirl strength. Aso et al. in Kyushu University employed multi-swirl injection to solve this problem. Combinations of swirling injection and paraffin based fuel have been tried and some results show very high regression rates exceeding ten times of conventional one. High fuel regression rates by new fuel, new internal ballistics, or combination of them require faster fuel-oxidizer mixing to maintain combustion efficiency. Nakagawa et al. succeeded to improve combustion efficiency of a paraffin-based fuel from 77% to 96% by a baffle plate. Another effective approach some researchers are trying is to use an aft-chamber to increase residence time. Better understanding of the new flow fields is necessary to reveal basic mechanisms of regression enhancement. Yuasa et al. visualized the combustion field in a swirling injection type motor. Nakagawa et al. observed boundary layer combustion of wax-based fuels. To understand detailed flow structures in swirling flow type hybrids, Sawada et al. (Tohoku Univ.), Teramoto et al. (Univ. of Tokyo), Shimada et al. (ISAS), and Tsuboi et al. (Kyushu Inst. Tech.) are trying to simulate the flow field numerically. Main challenges are turbulent reaction, stiffness due to low Mach number flow, fuel regression model, and other non-steady phenomena. Oshima et al. in Hokkaido University simulated CAMUI type flow fields and discussed correspondence relation between regression distribution of a burning surface and the vortex structure over the surface.

• The Korean Journal of Archival Studies
• /
• no.17
• /
• pp.247-292
• /
• 2008

Investigations have been started to set the modern history and national spirit to rights after Commissions were established. Those Commissions are established and operated with time limit to finish its own missions. They creates three kinds of records as acquired materials which acquired or are donated for investigation; investigation records as investigation reports; and administrative records that created while supporting organization's operation. The Commissions use more past records to do special tasks asnation's slate clean and uncovering the truth than other agencies. In other words, the commissions take the most advantages of well-managed records, however, their record management environment and operation systems are relatively loose than other permanent machineries. It has three reasons that; first, there is no record management regulations and criteria for machineries that have time limit. This affected each commissions 'systems and 6 Truth Commissions' record management systems are built separately and on the different level; Second, members lack responsibility from frequent sending, reinstatement, change, and restructuring and that makes troubles to produce and manage records; Third, central archives pay less attention to machineries that operated limited period as the truth commissions. The Commissions rather need more systematic control because its records have historical value. To solve these problems, record management regulations have to be prepared first with features of organizations running limited time and commissions' records as acquired materials or investigation records. Furthermore, building up standard record management system for the Commissions, standardizing transfer data, imposing professional record personnel, and setting limits frequent personnel changes would finish practical problems. Besides, those records created to reveal the truth should use for education and research because Truth Commissions are established to set unfortunate history right and not to repeat it again. The records would serve as steppingstone for establishment of the Truth Record Center that does education, information work, publication, and research with the records. The record center would help using the records efficiently and improving knowledge for its people. And, the center should devote people to recognize importance of the records.

• The Korean Journal of Archival Studies
• /
• no.21
• /
• pp.283-322
• /
• 2009

Legislation and enforcement of the Presidential Records Management Law was an important turning point in Korean archival management history. In the past, the notion of presidential records was vague. The law was a starting point of establishing presidential records management. The Presidential Records Management Law provides the definition of presidential records and its scope, and establishes the protection of presidential records through restricted access to the records. The key to the law is to enable a president freely to produce records and transfer them to the next administration without omission. In other words, it aims to stop the practice that presidential records are produced but never be left. But, 'disputes over the release of presidential records' and the disclosing of access-restricted presidential records presented a crisis to national records management as well as the prospect of presidential records management, even if they were 'legal procedures.' The instability of presidential records management could give a serious impact on the national records management and its operation. Amid this situation, it is required to review the presidential records management system and provide recommendations for improvement, even if the enforcement of law has just started. The most urgent things in improving presidential records management are to secure its independence, specialty, and to complement restricted access to presidential records. For securing independency, presidential records management should be done by a separate organization other than the National Archives of Korea while for promoting specialty, a newly established organization could serve as a professional archive. And for complementing restricted access to the presidential records, the access should be more limited. In other words, more discretion is needed in permitting access. And more specific regulations should be applied to the permitted records. However, these regulatory actions may not have effects unless independency is not secured. Thus, more fundamentally, independency of the National Archives of Korea should be first established.

• (The)Study of the Eastern Classic
• /
• no.69
• /
• pp.115-146
• /
• 2017

This paper is about the research on ontology design for a digital archive of seonsaengan(先生案) of the Joseon Period. Seonsaengan is the register of staff officials at each government office, along with their personal information and records of their transfer from one office to another, in addition to their DOBs, family clan, etc. A total of 176 types of registers are known to be kept at libraries and museums in the country. This paper intends to engage in the ontology design of 47 cases of such registers preserved at the Jangseogak Archives of the Academy of Korean Studies (AKS) with a focus on their content and structure including the names of the relevant government offices and posts assumed by the officials, etc. The work for the ontology design was done with a focus on the officials, the offices they belong to, and records about their transfers kept in the registers. The ontology design categorized relevant resources into classes according to the attributes common to the individuals. Each individual has defined a semantic postposition word that can explicitly express the relationship with other individuals. As for the classes, they were divided into eight categories, i.e. registers, figures, offices, official posts, state examination, records, and concepts. For design of relationships and attributes, terms and phrases such as Dublin Core, Europeana Data Mode, CIDOC-CRM, data model for database of those who passed the exam in the past, which are already designed and used, were referred to. Where terms and phrases designed in existing data models are used, the work used Namespace of the relevant data model. The writer defined the relationships where necessary. The designed ontology shows an exemplary implementation of the Myeongneung seonsaengan(明陵先生案). The work gave consideration to expected effects of information entered when a single registered is expanded to plural registers, along with ways to use it. The ontology design is not one made based on the review of all of the 176 registers. The model needs to be improved each time relevant information is obtained. The aim of such efforts is the systematic arrangement of information contained in the registers. It should be remembered that information arranged in this manner may be rearranged with the aid of databases or archives existing currently or to be built in the future. It is expected that the pieces of information entered through the ontology design will be used as data showing how government offices were operated and what their personnel system was like, along with politics, economy, society, and culture of the Joseon Period, in linkage with databases already established.

• Journal of the Society of Disaster Information
• /
• v.17 no.4
• /
• pp.722-732
• /
• 2021

Purpose: Due to the coronavirus infection-19 (COVID) pendemics, all educational institutions were required to provide full non-face-to-face real-time education, and fire officials were required to provide fire-fighting education by applying non-face-to-face education. In this difficult situation, the National Fire Service Academy tries to find the direction of the non-face-to-face real-time education and suggest ways to improve it through a survey of the status of non-face-to-face real-time education conducted by the NFSA to fire officials. Method: A survey was conducted on fire officials under the theme of "Consciousness Survey for Improving the Quality and Specialization of Non-face-to-face Real-Time Remote Education" and an in-depth analysis was conducted based on the results. Result & Conclusion: First, professors or educational operators shall actively utilize remote education programs suitable for educational characteristics by utilizing various programs. Second, a dedicated notebook for non-face-to-face training should be provided to provide an educational environment where all learners can participate in the training without difficulty. Third, in the case of education and training that requires the use of equipment due to the nature of fire officials' education and training, it is necessary to consider it as a non-face-to-face training place by arranging educational equipment at each fire station. Fourth, it is hard to expect a satisfactory educational effect to cope with practical education with theoretical education. Therefore, facilities and programs that enable non-face-to-face real-time hands-on training should be developed. It is worth considering the proper combination of face-to-face education while maintaining the social distance as much as possible until such non-face-to-face training is possible. Fifth, non-face-to-face education is considered to have high eye fatigue due to the light and electromagnetic waves of the computer screen, and as time goes by, the concentration level decreases. Therefore, it is necessary to form an education time to reduce the eye fatigue of learners and increase concentration through proper class and rest time. Finally, professors should operate a learner participation-oriented education that allows professors and learners to interact rather than one-sided knowledge transfer education. In addition, technical problems of non-face-to-face remote education should be thoroughly prepared through preliminary system checks to ensure that education is not disrupted.