• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.10
• /
• pp.999-1004
• /
• 2011

In this paper, calculation method of mutual inductance for two circular coils which are widely used in wireless power transfer system and analysis results using the method are proposed. Two circular coils are arranged in a perpendicular way. For calculation of the mutual inductance, an Rx coil placed perpendicularly with the other coil is uniformly subdivided into many unit cells and both magnetic flux density linked with the Rx coil at each unit cell and the total magnetic flux density of the Rx coil are obtained. Two circular coils are considered as a filamentary coil and uniform current density on each coil is assumed. For verification, helical and spiral coils are fabricated. As a result of measurement in 50 cm to 100 cm distance, theoretical mutual inductance is almost agreed with measured one.

• Journal of Embryo Transfer
• /
• v.26 no.3
• /
• pp.187-193
• /
• 2011

This study was carried out to establish most suitable freezing condition, to evaluate the different glycerol concentration of freezing and thawing rates on motility, viability, membrane integrity and acrosome intecrity of frozen Korean Jeju Black Bull spermatozoa, Semen was collected from a Korean Jeju Black Bull using an artificial vagina and transported to the laboratory. The semen was extended gradually 1:5 then cooled slowly for 2 hrs to 4$^{\circ}C$. The semen was diluted 1:1 with cryoprotectant extenders (3%, 5% and 7% glycerol) and equilibrated for 2 hrs at cold chamber and packed to 0.5 ml straws. The semen straws were located above 3 cm of liquid nitrogen for 5 minutes, above 5 cm for 10 min and above 8 cm for 10 min. And then the frozen straw was plunged into LN$_2$. The presented straws were examined the viability and motility after thawed at 37$^{\circ}C$ water bath. The viability and membrane integrity immediately post-thawing were significantly higher in samples frozen in 7% glycerol than 3% and 5% glycerol (p<0.05). After CTC staining to assess acrosome integrity, F pattern was significantly increased, but B pattern was significantly decreased in 7% glycerol (p<0.05). Freezing distance of 5 cm from liquid nitrogen and pre-cooling for 10 min yield better survival and membrane integrity, but not significant difference. However, AR pattern according to CTC staining was significantly decreased in 3 cm for 5 min.

• Journal of the Korean association of regional geographers
• /
• v.14 no.6
• /
• pp.718-735
• /
• 2008

Park-and- Rides are intermodal transfer facilities providing a staging location for travellers to transfer between transportation modes. They are an alternative to alleviate transportation problems such as traffic congestion and air pollution in metropolitan areas. Siting Park-and-Ride facilities belongs to a kind of multi-criteria spatial decision making problems being associated with a combination of various location factors. The purpose of this paper is to provide a method and procedure to evaluate the location suitability of Park-and-Ride facilities using GIS(Geographic Information Systems). Using GIS-based suitability analysis, land value, landuse, road accessibility, public transportation accessibility, possibility to intercept automobile trips, distance to activity center and competition with existing facilities were evaluated as location factors. The suitabilities of individual factors were combined to produce a composite map with a specific weight scheme. Then a given number of sites with high suitability score were selected as potential facility locations and their demand were evaluated based on a commutershed with parabolic shape. The suggested method and procedure will provide useful information in determining Park-and-Ride sites and designing their structure.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.41 no.2
• /
• pp.156-164
• /
• 2005

The size of the ship's turning circle is influenced by various factors, such as block coefficient, underwater side shape, rudder area ratio, draft, trim and Froude's number. Most of them are already fixed on departure from a port. However, the ship's speed and the rudder angle are controllable factors which operations are able to change optionally during sailing. The DGPS measured the turning circles according to the ship's speed and the rudder angle. The maximum advances by slow and full ahead were 302m and 311m, and the maximum transfers were 460m and 452m, respectively. There occurs almost no difference in size of the turning circle by variation of the ship's speeds. When the rudder angles were changed to $10^{\circ}$, $20^{\circ}$ and $30^{\circ}$, the maximum advances were 447m, 271m and 202m, and then also the maximum transfers 657m, 426m and 285m, respectively. The diameter of the tuning circle was decreased exponentially when the rudder angle was increased. The maneuverability was better when the direction of turning and propulsion of propeller are in the opposite direction rather than in the same one togetherm. The distance of the maximum transfer was always bigger than that of the maximum advance.

• Journal of Satellite, Information and Communications
• /
• v.9 no.1
• /
• pp.90-96
• /
• 2014

This paper is about increasing transfer efficiency of wireless power transmission. The new method is proposed to detect the alignment of transmitter and receiver of wireless charger and so smart phone can display the position of wireless charging receiver on its LCD panel for the maximum charging efficiency. The previous method is only to show the transfer efficiency, but this method is to show not only the efficiency but also coordinates of receiver. The apparatus of the wireless charger is based on WPC(Wireless Power Consortium) standard and has planar air coil combined with magnet shield in Tx and Rx device so that the leakage flux is minimized on condition of under hundreds of kHz operating frequency. In this paper, it's showed that relation of magnet field and distance of each coils can be linearized and position information of Tx and Rx device is calculated thru trigonometry. Through the experiment, the obstacles of linearity are discovered and also showed that it can be optimized. and so the presented method is suitable for alignment detection method of Tx and Rx device in WPC wireless charger.

• Korean Chemical Engineering Research
• /
• v.50 no.6
• /
• pp.1049-1055
• /
• 2012

The fiber mat catalytic burner that uses infrared radiative heat obtained by flameless catalytic combustion was manufactured and tested to investigate its combustion characteristics. About 9 to 17% of combustion heat was released by sensible heat during the premixed catalytic combustion depend on combustion condition. To find out radiation intensity with distance between catalytic burner and sample, the equation that calculate the receiving surface of radiative energy under the fiber mat catalytic burner was driven. This equation was well correlated with the drying rate of melamine. The drying experiments were carried out to the melamine, wood chip and agricultural pallet by using the fiber mat catalytic burner and the energy efficiency was calculated from drying rate of them. The energy efficiency of the fiber mat catalytic burner reaches to 79% in maximum for drying of the wood chip.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.11
• /
• pp.696-701
• /
• 2016

In this study, to increase output of road piezoelectric energy harvester, it was made into rack type in which many piezoelectric materials can be installed and load transfer device of the leverage type to transfer vehicle load was made. By paving it in the road, the output characteristics depending on vehicle load and speed were evaluated. Changing vehicle load, harvester output characteristics depending on speed changes were evaluated at the interval of 10 km/h from 10 km/h to 100 km/h. Also, by making a wireless switch and sending wireless signal with output of rack type harvester, whether to receive it was evaluated by distance. It was checked that all switches work up to front-to-back 100 m from harvester.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.4 no.1 s.6
• /
• pp.1-13
• /
• 2005

For integrated transit networks operated with diverse transit modes, it is difficult to find related literatures on the provision of multiple travel time routes information. This study proposes a methodology on how to select K number of least time transit routes in the integrated transit network with two modes, bus and subway. In the Proposed method, three constraints usually (will be) encountered for decision by users-(1) service time constraints of travel modes, (2) maximum payment fare constraints under the integrated distance based fare system, and (3) maximum number of transfer constraints - are taken into consideration in the searched routes. The experimental studies shows that the proposed method properly provides K number of least time routes. In addition, it somehow proves that by combinatorially considering three constraints the proposed method can be evaluated as to enlarge the quality as well as the diversity of route information demanded by users.

• Food Science of Animal Resources
• /
• v.28 no.3
• /
• pp.312-318
• /
• 2008

The objective of this study was to investigate the changes in ice dendrite size during freezing process in gelatin matrix as a model food system in order to provide mathematical relation between freezing condition and ice dendrite size. Gelatin gel as a model matrix was frozen in unidirectional Neumann's type of heat transfer. The thermograms' analysis allowed to determine the freezing temperature of the sample, the position of the freezing front versus time, and thus, freezing front rate. The morphology of ice dendrites was observed by scanning electron microscopy after freeze-drying. We observed that the means size of ice dendrite increased with the distance to the cooling plate; however, it decreased with the cooling rate and the cooling temperature. In addition, the shorter durations of the freeze-drying process was shorter decreeing the decreased the freezing front rate, resulted in their resulting in a larger pore size of the ice dendrite pores for the sublimation channel of that operate as water vapor sublimation channels. From these results, we could derive a linear regression as an empirical mathematical model equation between the ice dendrite size and the inverse of freezing front rate.

• Progress in Superconductivity and Cryogenics
• /
• v.18 no.1
• /
• pp.46-49
• /
• 2016

The wireless power transfer (WPT) system using a magnetic resonance was based on magnetic resonance coupling of the transmission and the receiver coils. In these system, it is important to maintain a high quality-factor (Q-factor) to increase the transmission efficiency of WPT system. Our research team used a superconducting coil to increase the Q-factor of the magnetic resonance coil in WPT system. When the superconductor is applied in these system, we confirmed that transmission efficiency of WPT system was higher than normal conductor coil through a preceding study. The efficiency of the transmission and the receiver coil is affected by the magnetic shielding effect of materials around the coils. The magnetic shielding effect is dependent on the type, thickness, frequency, distance, shape of materials. Therefore, it is necessary to study the WPT system on the basis of these conditions. In this paper, the magnetic shield properties of the cooling system were analyzed using the High-Frequency Structure Simulation (HFSS, Ansys) program. We have used the shielding materials such as plastic, aluminum and iron, etc. As a result, when we applied the fiber reinforced polymer (FRP), the transmission efficiency of WPT was not affected because electromagnetic waves went through the FRP. On the other hand, in case of a iron and aluminum, transmission efficiency was decreased because of their electromagnetic shielding effect. Based on these results, the research to improve the transmission efficiency and reliability of WPT system is continuously necessary.