• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.10
• /
• pp.975-981
• /
• 2017

Savings in weight using lightweight materials such as aluminum alloy can lead to increase fuel economy. However, compared to steel, aluminum alloys have a lower strength for an equivalent life cycle. To reduce the weight of automobiles, research is being performed on the fabrication of lighter and stronger torque struts without having to sacrifice the safety of automotive components. In this study, a weight reduction design process for torque struts is proposed that is based on varying von-Mises stress contours using an aluminum alloy (A356) having a tensile strength of 245 MPa, instead of STKM11A steels. The optimized design can reduce the weight of the original steel torque strut by over 42% and it can contribute to the design of light-weight components and to the safe design of torque struts.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.5 no.2
• /
• pp.287-301
• /
• 2013

The present paper deals with the problems of yaw angle effects on podded propulsor performance. The study aims at providing insights on characteristics of podded propulsors in azimuthing condition. In this regard, a wide numerical simulation that concerned yaw angle effect measurement on podded propeller performance was performed. The Reynolds-Averaged Navier Stokes (RANS) based solver is used in order to study the variations of hydrodynamic characteristics of podded propulsor at various angles. At first, the propeller is analyzed in open water condition in absence of pod and strut. Next flow around pod and strut are simulated without effect of propellers. Finally, the whole unit is studied in zero yaw angle and azimuthing condition. Structured and unstructured mesh techniques are used for single propeller and podded propulsor. The performance curves of the propeller obtained by numerical method are compared and verified by the experimental results. The characteristic parameters including the torque and thrust of the propeller, the axial force and side force of unit are presented as function of velocity advance ratio and yaw angle. The results shows that the propeller thrust, torque and podded unit forces in azimuthing condition depend on velocity advance ratio and yaw angle.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.2
• /
• pp.170-176
• /
• 2008

Anti roll bar model for real time multibody vehicle dynamics model has been proposed using kinematic constraint. Anti roll bar have been modeled by kinematic relationship, and mass properties are neglected. Relative angle of torsion bar spring is computed by constraint about drop-link using Newton-Raphson iteration, and then the torque of torsion bar spring can be computed with the angle and torsion spring stiffness. Finally anti roll bar force acting on both knuckle can be calculated. To validate the proposed method, half car simulations of McPherson strut suspension and full car simulations are also carried out comparing with the ADAMS vehicle model with anti roll bar. CPU times are also measured to see the real-time capabilities of the proposed method.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.4
• /
• pp.965-980
• /
• 2014

This paper presents a new estimation method of full scale propulsive performance for the pulling type podded propeller. In order to estimate the drag of pod housing, a drag velocity ratio, which includes the effects of podded propeller loading and Reynolds number, is presented and evaluated through the comparison of model test and numerical analysis. By separating the thrust of propeller blade and the drag of pod housing, extrapolation method of pod housing drag to full scale is deduced, and correction method of propeller blade thrust and torque to full scale is presented. This study utilized the drag coefficient ratio of the pod housing as a measure for expanding it to full scale, but in order to increase the accuracy of performance evaluation, additional study is necessary on the method for the full scale expansion via separating the drag of pod body, strut and fin which consist the pod housing.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.6
• /
• pp.142-153
• /
• 2005

The brake judder is a phenomenon that the steering wheel is abnormally vibrating when the car is braked at a high speed. It is classified by the cold and the hot judder. The former is generated due to the initial uneven disk surface and the latter is resulted from the uneven heat spots on disc surface by repeatedly braking. There are two ways to reduce the judder. One is to control vibration by modification of the disk shapes and pad ingredients. The other is to improve modal characteristics of the suspension system. The latter approach is used in this research. In this paper, the real vehicle test and computer simulation are considered to systematically understand the judder phenomenon of the vehicle. The Macpherson strut suspension is employed. Especially, the judder sensitivity is calculated based on design sensitivity analysis. A bush stiffness was reworked and braking test was done to verify the sensitivity result. The judder reduction by the mode control was verified.