• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 추계학술대회
• /
• pp.97-100
• /
• 2006

Accelerating ability is one of the most important performance of the vehicle. Unlike conventional internal combustion vehicles and power-assist hybrid vehicles, the maximized acceleration of dual mode hybrid vehicles is not simply. achieved by maximizing engine or motor torque Because of the dynamic stability of planetary gear, speeds and torques control of engine, motor 1 and motor 2 is essential and according to control value, acceleration performance is changed There are two control values which are velocity and torque for each component totalling six. These six values can be variables for an objective function. However, because three velocity variables can be regarded as only one variable speed ratio and the remaining three torque variables can be solved analytically, without complicated numerical algorithm the solution for the objective function can be obtained. This optimized solution shows the best performance possible to the specified dual mode system.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.355-360
• /
• 2002

To calibrate a non-redundantly actuated parallel mechanism, one can find actual kinematic parameters by means of geometrical constraint of the mechanism's kinematic structure and measurement values. However, the calibration algorithm for a non-redundant case does not apply fur a redundantly actuated parallel mechanism, because the angle error of the actuating joint varies with position and the geometrical constraint fails to be consistent. Such change of joint angle error comes from constraint torque variation with each kinematic pose (meaning position and orientation). To calibrate a redundant parallel mechanism, one therefore has to consider constraint torque equilibrium and the relationship of constraint torque to torsional deflection, in addition to geometric constraint. In this paper, we develop the calibration algorithm fir a redundantly actuated parallel mechanism using these three relationships, and formulate cost functions for an optimization algorithm. As a case study, we executed the calibration of a 2-DOF parallel mechanism using the developed algorithm. Coordinate values of tool plate were measured using a laser ball bar and the actual kinematic parameters were identified with a new cost function of the optimization algorithm. Experimental results showed that the accuracy of the tool plate improved by 82% after kinematic calibration in a redundant actuation case.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.1330-1333
• /
• 1997

In this paper, the optimal torque shaping is obtained for 3-axis rotation of a spacecraft. The true optimal 3-axis rotation of rigid spaeraft is first investigated via parameter optimization method with prescribed switching times. Input torque shape of the troque generating device mounted on the central hub is optimized using fourier Series expansion so that the spacecraft may slew while minimizing the vibration energy of flexible modes. Numerical results show that proposed method suggests a reference trahectory for open-loop control, and also verify that it can minimize the vibratory modes of the spacecraft during/after the rest-to-rest maneuver.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1990년도 추계학술대회 논문집 학회본부
• /
• pp.19-22
• /
• 1990

In this paper, in order to reduce the cogging torque in a permanent motor, a method to optimize the shape of permanent magnet and iron pole is presented. Because the cogging torque comes from the irregular system energy variation according to the rotor position, system energy variation is taken as object function and the object function is minimized to optimize the shape. The positions of permanent magnet surface and iron pole surface are chosen as design parameters and sensitivity of object function with respect to design parameter is calculated. The shape is changed according to sensitivity. Sensitivity can be generated by methods that exploit the FEM formulation. A numerical example shows that about 90% of the original cogging torque is reduced.

• 대한전기학회논문지
• /
• 제39권12호
• /
• pp.1246-1252
• /
• 1990

In order to reduce the cogging torque in a permanent magnet motor, a method to optimize the shape of permanent magnet and iron pole is presented. Sine the cogging torque comes from the irregular system energy variation according to the rotor position, system energy variation is taken as object function and the object function is minimized to optimize the shape. The positions of permanent magnet surface and iron pole surface are chosen as design parameters and sensitivity of object function with respect to the design parameter is calculated. The shape is changed according to sensitivity can be generated by methods that exploit the FEM formulation. A numerical example shows that the cogging torque is reduced to about 10% of the original value.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1991년도 하계학술대회 논문집
• /
• pp.767-770
• /
• 1991

For the control of redundant manipulators, conventional dynamic control methods of local torque optimization showed the instability which resulted in physically unrealizable torque requirements. In this paper, a new dynamic control method which is based on the concept of aspects is proposed. The proposed method starts with the basic understanding of the minors in the Jacobian matrix. It was shown by computer simulations that the proposed method demonstrates a drastic reduction of torque loadings at the joints in the tracking motion of a long trajectory, and thus guarantees the stability of joint torque.

• 전기학회논문지
• /
• 제56권3호
• /
• pp.498-505
• /
• 2007

This paper proposes the novel flux barrier that built in q-axis in rotor of IPM type BLDC motor. The novel flux barrier aims to reduce the motor vibration with reduced cogging torque and lessened torque ripple by the sinusoidal waveform distribution of the flux generated in the permanent magnet. For optimization of the novel flux barrier, the Taguchi method is effectively employed which considered multiple objective quality characteristics, such as cogging torque, average torque and efficiency. The result of proposed model compare with the initial model and it is verified by 2D finite element method (FEM) results.

• Journal of Electrical Engineering and Technology
• /
• 제5권3호
• /
• pp.462-467
• /
• 2010

This paper presents the rotor shape optimization of an interior type permanent magnet (IPM) motor for a reduction of vibration and Electromagnetic Interference (EMI). The vibration and EMI in permanent magnet motors is generated by cogging torque ripple, radial force and commutation torque ripple. Consequently, in order to improve vibration and EMI, the optimal notches are put on the rotor pole with an arc shape proposed. The variation of vibration frequency due to the cogging torque and radial force of each model is computed by the finite element method (FEM). From the analysis result and experiment, we confirmed the proposed model has remarkably improved the vibration and EMI.

• 전기학회논문지
• /
• 제65권12호
• /
• pp.2183-2188
• /
• 2016

This paper deals with the design process for an outer-rotor-type surface-mounted permanent magnet synchronous motor (SPMSM) used in continuous variable valve timing (CVVT) systems in automobiles with internal combustion engines. When the same size, outer-rotor-type SPMSMs generate larger torque and more stable than inner-rotor-type SPMSMs. For the initial design, space harmonic analysis (SHA) is used. In order to minimize the cogging torque, an optimization was conducted using Response Surface Methodology (RSM). At the end of the paper, Finite Element Analysis (FEA) is performed to verify the performance of the optimum model.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제2권2호
• /
• pp.134-140
• /
• 2013

This paper proposes a new design of rotor shape of Interior Permanent Magnet Synchronous Motor (IPMSM) used for agricultural electric vehicle (AEV). The distribution of the residual magnetic flux density at the air gap is modified by rotor surface shape and V-type magnet angle. As a result, cogging torque and physical characteristic have been improved, and back electromotive force (back-EMF) of the suggested model has been improved to be closest to sine wave form compared to initial model. The validity of the proposed rotor shape optimization is confirmed by the manufactured IPM rotor core and measured the performance of the cogging torque.