• 산업공학
• /
• 제22권1호
• /
• pp.73-84
• /
• 2009

In this paper, we propose a dispatching algorithm for constructing a Factory Operating System (FOS) which can operate semiconductor fabrication factories more efficiently and effectively. We first define ten dispatching criteria and propose two methods to apply the defined dispatching criteria sequentially and simultaneously (i.e. fixed dispatching architecture). However the fixed type methods cannot apply the criteria adaptively by considering changes in the semiconductor fabrication factories. To overcome this type of weakness, an adaptive dispatching architecture is proposed for applying the dispatching criteria dynamically based on the factory status. The status can be determined by combining evaluation results from the following three status criteria; target movement, workload balance, and utilization rate. Results from the shop floor in past few periods showed that the proposed methodology gives a good performance with respect to the productivity, workload balance, and machine utilization. We can expect that the proposed adaptive dispatching architecture will be used as a useful tool for operating semiconductor fabrication factories more efficiently and effectively.

• 한국공작기계학회논문집
• /
• 제16권4호
• /
• pp.22-28
• /
• 2007

The welded defects are usually called user's unsatisfaction for appearance and functional usage. For checking these defects effectively without time loss, setup of weldability estimation system is an important for detecting whole specimen quality. In this study, after catching a rawdata on welded specimen profiles and treating vision processing with these data, the qualitative defects are estimated from getting these information by laser vision camera at first. At the same time, the weldability estimation for whole specimen is produced. For user friendly, the weldability estimation results are shown each profiles, final reports and visual graphics method. So, user can easily determined weldability. By applying these system to welding fabrication, these technologies are contribution to on-line setup of weldability estimation system.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.560-564
• /
• 1999

Burr sensing for burr size measurement and deburring process control is one of the essential elements in an automated deburring procedure. This paper presents the implementation of capacitance sensing and acoustic emission (AE) to deburring. The first application is the "on-line" measurement of burrs using a capacitance sensor. A non-contact capacitance gauging sensor is attached to an ultra precision milling machine which was used as a positioning system. The setup is used to measure burr profiles along machined workpiece edges. The proposed scheme is shown to be accurate, easy to setup, and with minor modifications, readily applicable to automatic deburring processes. As the second example, AE signals were sampled and analyzed for the sensor feedback of a precision deburring process - laser deburring -. The results, such as the sensitivity of AE signals to burr shapes and edge detection capability show a clear correlation between physical process parameters and the AE signals. A subsequent control strategy for deburring automation is also briefly discussed.

• ETRI Journal
• /
• 제36권4호
• /
• pp.673-681
• /
• 2014

Fairness of exchange is a significant property for secure online transactions, and a fair exchange scheme is a useful tool for ensuring the fairness of exchanges conducted over networks. In this paper, we propose an ID-based optimistic fair exchange scheme based on the RSA function, one which is designed by combining a well-known RSA-based signature scheme and the (naive) RSA function. Note that the main contribution of this paper is to give the first provably secure ID-based fair exchange scheme based on the RSA function, whose security can be proved under fully formalized security models. Our scheme has the following additional strongpoints. The scheme is setup-free; hence, there is no registration step between a user and an arbitrator. Moreover, the proposed scheme is designed in an ID-based setting; thus, it is possible to eliminate the need for certificates and avoid some related problems.

• 한국정밀공학회지
• /
• 제22권12호
• /
• pp.198-204
• /
• 2005

For precise micro V-grooving, ultrasonic elliptical vibration cutting (UEVC) is proposed using two parallel piezoelectric actuators, which are energized by sinusoidal voltages with a phase difference of 90 degrees. Experimental setup is composed of stacked PZT actuators, a single crystal diamond cutting tool, and a precision motorized xyz stage. It is found that the chip formed in the process of UEVC is discontinuous because of the periodic contacts and non-contacts occurring between the tool and workpiece. It is experimentally observed that the cutting force in the process of UEVC significantly reduces compared to the ordinary non-vibration cutting. In addition, the creation of burr during UEVC is significantly suppressed, which is attributable to the decrease in the specific cutting energy.

• 한국정밀공학회지
• /
• 제16권1호통권94호
• /
• pp.219-225
• /
• 1999

Monitoring of the cutting force signals in cutting process has been well emphasized in machine tool communities. Although the cutting force can be directly measured by a tool dynamometer, this method is not always feasible because of high cost and limitations in setup. In this paper an indirect cutting force monitoring system is developed so that the cutting force in turning process is estimated based on a AC spindle drive model. This monitoring system considers the cutting force as a disturbance input to the spindle drive and estimates the cutting force based on the inverse dynamic model. The inverse dynamic model represents the dynamic relation between the cutting force, the motor torque and the motor power. The proposed monitoring system is realized on a CNC lathe and its estimation performance is evaluated experimentally.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.358-362
• /
• 2004

Higher productivity requires high-speed motion of machine tool axes. The iron core linear DC motor (LDM) is widely accepted as a viable candidate for high-speed machine tool feed unit. LDM, however, has two inherent disturbance force components, namely cogging and thrust force ripple. These disturbance forces directly affect the tracking accuracy of the feeding system and must be eliminated or reduced. In order to reduce motor ripple, this research adapted the feedforward compensation method and neural network control. Experiments carried out with the linear motor test setup show that these control methods are effective in reducing motor ripple.

• 한국정밀공학회지
• /
• 제32권5호
• /
• pp.447-454
• /
• 2015

Design and application of hardware-in-the-loop simulation (HILS) for design of CNC-controlled machine tool feed drives is discussed. The CNC machine tool is a complex mechatronics system where the complexity results from the software-based controller composed of a variety of functionalities and advanced control algorithms. Therefore, using a real CNC controller in the control simulation has merits considering the efforts and accuracy of the simulation modeling. In this paper challenges in HILS for a CNC controlled feed drive, such as minimization of time delay and transmission error that are caused by discretization of the feed drive model, is elaborated. Using an experimental HILS setup of a machine tool feed drive applications in controller gain selection and CNC diagnostics are presented.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.620-623
• /
• 1996

POSCO has been developed a general purpose dynamic simulator of the hot strip steel mill. The simulator is a tool for developing the process control system in an industrial system solution business, by making the most use of control and simulation techniques fostered in steelmaking business. This simulator has, not only a powerful numerical analysis function, but an easy-to-use graphic user interface which readily enables to simulate dynamic system. This paper presents the features of the simulator and steel rolling process simulator as its application.

• 대한자기공명의과학회:학술대회논문집
• /
• 대한자기공명의과학회 1997년도 제2차 추계학술대회 초록집
• /
• pp.50-50
• /
• 1997