• Journal of Electrical Engineering and Technology
• /
• v.6 no.5
• /
• pp.684-687
• /
• 2011

In this study, we investigate the photovoltaic performance of transparent conductive indium tin oxide (ITO), titanium-doped indium oxide (ITiO), and fluorine-doped tin oxide (FTO) films. ITO and ITiO films are prepared by radio frequency magnetron sputtering on soda-lime glass substrate at $300^{\circ}C$, and the FTO film used is a commercial product. We measure the X-ray diffraction patterns, AFM micrographs, transmittance, sheet resistances after heat treatment, and transparent conductive characteristics of each film. The value of electrical resistivity and optical transmittance of the ITiO films was $4.15{\times}10^{-4}\;{\Omega}-cm$. The near-infrared ray transmittance of ITiO is the highest for wavelengths over 1,000 nm, which can increase dye sensitization compared to ITO and FTO. The photoconversion efficiency (${\eta}$) of the dye-sensitized solar cell (DSC) sample using ITiO was 5.64%, whereas it was 2.73% and 6.47% for DSC samples with ITO and FTO, respectively, both at 100 mW/$cm^2$ light intensity.

• Journal of the Korean institute of surface engineering
• /
• v.52 no.6
• /
• pp.306-309
• /
• 2019

Titanium (Ti) doped indium oxide (In₂O₃) films were deposited on glass substrates by RF magnetron sputtering and the films were rapid thermal annealed at 100, 200, and 300℃, respectively to investigate the influence of the rapid annealing on the opto-electrical performance of the films. The grain size of In₂O₃ (222) plane increased with annealing temperatures and their electrical resistivity decreased to as low as 8.86×10^-4 Ωcm at 300℃. The visible transmittance also improved from 77.1 to 79.5% when the annealing temperature increased. The optical band gap of the TIO films shifted from 4.010 to 4.087 eV with increases in annealing temperature from room temperature to 300℃. The figure of merit shows that the TIO films annealed at 300℃ had better optical and electrical performance than the other films prepared using lower-temperature or no annealing.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.200-200
• /
• 2010

In recent times, metal oxide semiconductors thin films transistor (TFT), such as zinc and indium based oxide TFTs, have attracted considerable attention because of their several advantageous electrical and optical properties. There are many deposition methods for fabrication of ZnO-based materials such as chemical vapor deposition, RF/DC sputtering and pulsed laser deposition. However, these vacuum process require expensive equipment and result in high manufacturing costs. Also, the methods is difficult to fabricate various multicomponent oxide semiconductor. Recently, several groups report solution processed metal oxide TFTs for low cost and non vacuum process. In this study, we have newly developed solution-processed TFTs based on Ti-related multi-component transparent oxide, i. e., InTiO as the active layer. We propose new multicomponent oxide, Titanium indium oxide(TiInO), to fabricate the high performance TFT through the sol-gel method. We investigated the influence of relative compositions of Ti on the electrical properties. Indium nitrate hydrate [$In(NO^3).xH_2O$] and Titanium isobutoxide [$C_{16}H_{36}O_4Ti$] were dissolved in acetylacetone. Then monoethanolamine (MEA) and acetic acid ($CH_3COOH$) were added to the solution. The molar concentration of indium was kept as 0.1 mol concentration and the amount of Ti was varied according to weighting percent (0, 5, 10%). The complex solutions become clear and homogeneous after stirring for 24 hours. Heavily boron (p+) doped Si wafer with 100nm thermally grown $SiO_2$ serve as the gate and gate dielectric of the TFT, respectively. TiInO thin films were deposited using the sol-gel solution by the spin-coating method. After coating, the films annealed in a tube furnace at $500^{\circ}C$ for 1hour under oxygen ambient. The 5% Ti-doped InO TFT had a field-effect mobility $1.15cm^2/V{\cdot}S$, a threshold voltage of 4.73 V, an on/off current ratio grater than $10^7$, and a subthreshold slop of 0.49 V/dec. The 10% Ti-doped InO TFT had a field-effect mobility $1.03\;cm^2/V{\cdot}S$, a threshold voltage of 1.87 V, an on/off current ration grater than $10^7$, and a subthreshold slop of 0.67 V/dec.

• Journal of the Korean institute of surface engineering
• /
• v.52 no.6
• /
• pp.289-292
• /
• 2019

Transparent and conducting titanium doped indium oxide (TIO) thin films were deposited by RF magnetron sputtering on zinc oxide (ZnO)-coated glass substrates to investigate the effect of the ZnO buffer layer on optical and electrical properties of TIO/ZnO bi-layered films. TIO 90 nm / ZnO 10 nm films having a lower resistivity (3.09×10^-3 Ωcm) and a higher visible transmittance (80.3%) than other TIO/ZnO films were prepared in this study. Figure of merit results indicate that a 10 nm thick ZnO thin film is an effective buffer layer that enhances optical transmittance and electrical conductivity of TIO films without intentional substrate heating or post-deposition annealing.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1150-1151
• /
• 2008

Titanium-doped indium oxide (ITiO) films were prepared on soda-lime glass substrate using a magnetic null discharge (MND) sputter source. The ITiO thin films containing 10 wt.% Ti showed the minimum resistivity of ${\rho}=5.5{\times}10^{-3}{\Omega}cm$. The optical transmittance increases from 70% at 450 nm to 80% at 700 nm in visible spectrum. The surface roughness of the sample showed a change from 10 nm to 50 nm. The ITiO film used for TCO layer of DSCs exhibited an energy conversion efficiency of about 3.8 % at light intensity of 100 $mW/cm^2$.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1485_1486
• /
• 2009

Transparent conductive metal oxide films of $In_{2-x}Sn_xO_3$ (ITiO) and $In_{2-x}Sn_xO_3$ (ITO) were deposited by RF magnetron sputtering at relatively low substrate temperature (~$300^{\circ}C$) and at high rate (~10nm/min). Electrical and optical properties of the films were investigated as well as film structure and morphology, as it is compared with the commercial F:$SnO_2$ (FTO) glass. Near infrared ray transmittance of ITiO is the highest for wavelengths over 1000nm, which can increase dye sensitized compared to ITiO and FTO. Dye-sensitized solar cells (DSCs) were fabricated using the ITiO, ITO and FTO. Photoconversion efficiency ($\eta$) of DSC using ITiO is 5.5%, whereas 5.0% is obtained from DSC with ITO, both at 100mW/$cm^2$ light intensity.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.10a
• /
• pp.205-210
• /
• 2008

Titanium-doped indium oxide (ITiO) films were prepared on soda-lime glass substrate using a magnetic null discharge (MND) sputter source. The ITiO thin films containing 10wt.% Ti showed the minimum resistivity of $\rho=5.5{\times}10^{-3}{\Omega}-cm$. The optical transmittance increases from 70% at 450 nm to 80% at 700 nm in visible spectrum. Photoelectron peaks for In 3d, Ti 2p, O 1s and C1s were detected for the ITiO film in the binding energy range of 0 to 1100 eV. The surface roughness of the sample showed a change from 10 nm to 50 nm. The ITiO film used for TCO layer of DSCs exhibited an energy conversion efficiency of about 3.8% at light intensity of 100 mW/$cm^2$.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.4
• /
• pp.193-197
• /
• 2023

Transparent and conducting titanium (Ti) doped indium oxide (TIO) thin films were deposited on the poly-imide (PI) substrate with radio frequency magnetron sputtering and then electron irradiation was conducted on the TIO film's surface to investigate the effect electron irradiation on the crystallization and opto-electrical properties of the films. All x-ray diffraction (XRD) pattern showed two diffraction peaks of the In₂O₂ (431) and (444) planes with regardless of the electron beam irradiation energy. In the AFM analysis, the surface roughness of as deposited films was 3.29 nm, while the films electron irradiated at 700 eV, show a lower RMS roughness of 2.62 nm. In this study, the FOM of as deposited TIO films is 6.82 × 10^-3 Ω^-1, while the films electron irradiated at 500 eV show the higher FOM value of 1.0 × 10^-2 Ω^-1. Thus, it is concluded that the post-deposition electron beam irradiation at 500 eV is the one of effective methods of crystallization and enhancement of opto-electrical performance of TIO thin film deposited on the PI substrate.