• The Korean Journal of Ceramics
• /
• 제5권4호
• /
• pp.324-330
• /
• 1999

$Si_3N_4$-$TiB_2$ with 2 wt% $Al_2O_3$ and 4 wt% $Y_2O_3$ additives was hot pressed in a flowing $N_2$ environment with varying $TiB_2$ content from 10 to 50 vol%. Variations of mechanical (hardness, fracture toughness, and flexual strength), and tribological properties as a function of $TiB_2$ content were investigated. As the content of $TiB_2$ increased, relative density decreased due to the chemical reaction of $TiB_2$in $N_2$ environment. The reduction of density causes mechanical properties to be degraded with an increase of $TiB_2$ in $Si_3N_4$. Tribological properties were dependent of microstructure as well as mechanical properties, however, they were degraded strongly by the chemical reaction of $Si_3N_4$-$TiB_2$ during hot pressing in $N_2$ environment. SEM and TEM observations, and X-ray diffraction analysis that the chemical reaction products at the interface are TiCN, Si, and $SiO_2$. Also, the comparison of XRD patterns of the $Si_3N_4$-40 vol% $TiB_2$ composites hot pressed at $1,750^{\circ}C$ for 1 hour between in $N_2$ and in Ar gas was made. The XRD peaks of Si and $SiO_2$ were not found in Ar, but still a weak peak of TiCN was presented.

• Korean Chemical Engineering Research
• /
• 제46권4호
• /
• pp.676-680
• /
• 2008

Radio-frequency (rf) 마그네트론 스퍼터링법을 이용하여 $SiO_2(2000{\AA})/Si$ 기판위에 TiN 박막이 증착되었다. $N_2/Ar$ 혼합가스에서 $N_2$ 가스의 농도, rf power, 공정압력 등을 변화시켜서 TiN 박막이 증착되었고 증착된 박막의 증착속도, 전기저항도 및 표면의 거칠기 등이 조사되었다. $N_2$ 가스의 농도가 증가함에 따라서 증착속도는 감소하였고 저항도는 증가하였으며 표면의 거칠기는 감소하였다. rf power가 증가함에 따라서 증착속도는 증가하였지만 저항도는 감소하였다. 증착압력의 증가에 따라서 증착속도는 큰 변화가 없었지만 저항도가 급격히 증가하였으며, 1 mTorr의 압력에서 $2.46{\times}10^{-4}{\Omega}cm$의 저항도를 갖는 TiN 박막이 얻어졌다. 박막의 증착속도와 저항도는 상관관계가 있는 것이 관찰되었고 특히 증착압력이 박막의 저항도에 가장 큰 영향을 미치는 것을 알 수 있었다.

• 대한전자공학회논문지SD
• /
• 제40권12호
• /
• pp.1-9
• /
• 2003

본 논문에서는 cobalt interlayer와 TiN capping을 적용한 Ni-Silicide 구조를 제안하여 100 ㎜ CMOS 소자에 적용하고 소자 특성 연구를 하였다. Ni-Silicide의 취약한 열 안정성을 개선하기 위해 열 안정성이 우수한 Cobalt interlayer이용하여 silicide의 열화됨을 개선하였고 또한 silicide 계면의 uniformity를 향상하기 위해 TiN capping을 동시에 적용하였다. 100 ㎚ CMOS 소자에 제안한 Co/Ni/TiN 구조를 적용하여 700℃, 30분에서의 열처리 시에도 silicide의 낮은 면저항과 낮은 접합 누설 전류가 유지되었으며 100 ㎚이하 소자의 특성 변화도 거의 없음을 확인하였다. 따라서 제안한 Co/Ni/TiN 구조가 NiSi의 열 안정성을 개선시킴으로써 100 ㎚ 이하의 Nano CNOS 소자에 매우 적합한 Ni-Silicide 특성을 확보하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.161-161
• /
• 2012

질화티타늄(Titanium Nitride, TiN)은 화학적 안정성이 우수하고, N/Ti 원소 비율에 따라 열전도성 및 전기전도성이 변화하는 특성을 가지고 있어서 Metal Insulator Silicon (MIS) 나 Metal Insulator Metal (MIM) capacitor의 metal electrode 물질로 적용되고 있다. $TiCl_4$와 $NH_3$ gas를 이용하여 $500^{\circ}C$ 이상의 고온 조건에서 Chemical Vapor Deposition (CVD) 법으로 TiN 박막을 증착하는 방식이 가장 널리 사용되고 있으나, TiN 박막 내의 Chlorine (Cl) 원소가 SiO2 두께와 누설전류 밀도를 증가시키는 요인으로 작용하므로 Cl의 거동 및 함량 제어를 통한 전기적인 특성의 향상 평가가 요구되고 있다[1-3]. 본 실험에서는 $SiO_2$ 위에 TiN을 적층 한 구조에서 magnetic sector type의 Secondary Ion Mass Spectrometry (SIMS)를 이용하여 Cl 원소의 검출도 개선 방법을 연구하였다. 일반적인 $Cs^+$ 이온을 이용하여 $Cl^-$ 이온을 검출할 경우에는 TiN 하부에 $SiO_2$가 존재함에 따른 charging effect와 mass interference가 발생되는 문제점이 관찰되었다. 이를 개선하기 위해 Cl과 Cs 원소가 결합된 $ClCs^+$ cluster ion을 검출하는 방법을 시도하였으나, Cl- 이온 검출 방식에 비해 오히려 낮은 검출도를 나타내었으나 Cl 원소가 속하는 halogen 족 원소의 높은 전자 친화도 특성을 이용한 $ClCs_2^+$ cluster ion을 검출하는 방법[4]을 적용한 경우에는 $ClCs^+$ 방식에 비해 검출도가 3order 개선되는 결과를 확보하였으며, 이 결과를 토대로 Cl dose ($atoms/cm^2$) 와 Rs (ohm/sq) 간의 상관 관계에 대해 고찰하고자 한다.

• 한국표면공학회지
• /
• 제52권3호
• /
• pp.163-170
• /
• 2019

Durability of instrument is one of the most important factor to ensure accurate treatment and decrease failure for the orthopedic surgical operation. Normally, a set-screw driver tip has been processed with hard coating for their higher durability and wear resistance. And several surface modification methods were obtained such as titanium nitride (TiN) coating, diamond like carbon coating, other nitriding, and etc. In this study, we have surface modified on set-screw driver tip with TiN and DLC, investigated whether the TiN and DLC coatings affect the mechanical properties and durability of the set-screw driver tip in the pedicle screw system. The surface morphologies were observed with scanning-electron microscopy (SEM), and the static/dynamic torsional properties were investigated with universal testing machine based on ASTM F543. Coating thickness of each coatings were commonly around $1^{\circ}C$. Static torsional stiffness, and ultimate torque values for DLC and TiN coated samples were significantly higher than those of non-coated sample by the pared T-test. Surface morphology of after the dynamic torsional test was more clean with less scratch or friction traces from DLC coating than that of TiN coating and non-coated sample.

• 한국반도체및디스플레이장비학회:학술대회논문집
• /
• 한국반도체및디스플레이장비학회 2003년도 추계학술대회 발표 논문집
• /
• pp.1-6
• /
• 2003

Flow modulation chemical vapor deposition process has been reported as an alternative way to obtain low resistivity, low residual chlorine content and good step-coverage titanium nitride film. Flow and concentration characteristics in a vertical FMCVD reactor are analyzed by using computational fluid dynamics method. The results show that 1.0 second as Cl reduction period is too short and there is still $TiCl_4$ gas above the holder at the end of the period. Time variation of $TiCl_4$ gas concentration on the holder shows that at least 3.0 second is necessary as Cl reduction time for the sake of film characteristics.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.36-37
• /
• 2006

Titanium oxy-nitride ($TiN_O_y$) thin films were deposited on $SiO_2$/Si substrates using reactive dc magnetron sputtering, and were then annealed at various temperatures in air ambient to incorporate oxygen into the films. The effect of annealing temperature on the structural and electrical properties of the films was investigated. The grain size of the films decreases with increasing annealing temperature. On the other hand, crystallinity of the films is independent of annealing temperature in air ambient. Resistivity of the films increases remarkably as an annealing temperature increases and temperature coefficience of resistance (TCR) of the films varies from a positive value to a negative value. The films annealed at $350^{\circ}C$ for 30 min exhibited a near-zero TCR value of approximately -5 ppm/K. The decrease of the grain size with increasing annealing temperature was attributed to an increase of oxygen concentration incorporated into the films during anncaling treatment.

• 한국재료학회지
• /
• 제5권5호
• /
• pp.552-559
• /
• 1995

Titanium nitride films were deposited on the (100) oriented-p-type silicon substrates of RF plasma enhanced chemical vapor depositiom\n using a gaseous mixutre of TiCl$_{4}$, N$_{2}$, H$_{2}$ and Ar. The chemincal composition, structure and the rsistivituy of the films were investigated with the deposition variables such as the flow rate ratio of N$_{2}$/TiCl$_{4}$, the deposition temperature and the RF power. The deposition rate increases with increasing the flow rate ratio of N$_{2}$TiCl$_{4}$ and RF power, while the rate decreases with increasing the deposition temperature. As the flow rate ratio of N$_{2}$/TiCl$_{4}$ and depostion temperature increases within proper RF pwoer, the Cl concentartion in the films decreases and the stoichiometry and crystallingiy are improved, so decreases the resistivity of the films. The films depostied under the condition of the N$_{2}$/TiCl$_{4}$ ratio of 30, the RF power of 50W and the depostion temperature of 62$0^{\circ}C$ had the Cl content of 1.5at% and the resistivity of 56㏁cm. Also, the bottom coverage of the films was above 60% on the step with the width and depth of 0.6${\mu}{\textrm}{m}$$\times$0.6${\mu}{\textrm}{m}$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.74-74
• /
• 2009

Titanium nitride has been used as hardmask for semiconductor process, capacitor of MIM type and diffusion barrier of DRAM, due to it's low resistivity, thermodynamic stability and diffusion coefficient. Characteristics of the TiN film are high intensity and chemical stability. The TiN film also has compatibility with high-k material. This study is an experimental test for better condition of TiN film etching process. The etch rate of TiN film was investigated about etching in $BCl_3/Ar/O_2$ plasma using the inductively coupled plasma (ICP) etching system. The base condition were 4 sccm $BCl_3$ /16 sccm Ar mixed gas and 500 W the RF power, -50 V the DC bias voltage, 10 mTorr the chamber pressure and $40\;^{\circ}C$ the substrate temperature. We added $O_2$ gas to give affect etch rate because $O_2$ reacts with photoresist easily. We had changed $O_2$ gas flow rate from 2 sccm to 8 sccm, the RF power from 500 W to 800 W, the DC bias voltage from -50 V to -200 V, the chamber pressure from 5 mTorr to 20 mTorr and the substrate temperature from $20\;^{\circ}C$ to $80\;^{\circ}C$.

• 한국세라믹학회지
• /
• 제49권4호
• /
• pp.333-336
• /
• 2012

The study to give electrical conductivity by dispersing carbon nanotubes (CNT) into silicon nitride ($Si_3N_4$) ceramics has been carried out in recent years. However, the density and the strength of $Si_3N_4$ ceramics were degraded and CNTs disappeared after firing at high temperatures because CNTs prevent $Si_3N_4$ from densification and there is a possibility that CNTs react with $Si_3N_4$ or $SiO_2$. In order to suppress the reaction and the disappearance of CNTs, lower temperature densification is needed. In this study, $HfO_2$ and $TiO_2$ was added to $Si_3N_4-Y_2O_3-Al_2O_3$-AlN system to fabricate CNT-dispersed $Si_3N_4$ ceramics at lower temperatures. $HfO_2$ promotes the densification of $Si_3N_4$ and prevents CNT from disappearance. As a result, the sample by adding $HfO_2$ and $TiO_2$ fired at lower temperatures showed higher electrical conductivity and higher bending strength. It was also shown that the mechanical and electrical properties depended on the quantity of the added CNTs.