• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.283.1-283.1
• /
• 2016

Tin Oxide(SnO2) has been widely investigated as a transparent conducting oxide (TCO) and can be used in optoelectronic devices such as solar cell and flat-panel displays. It would be applicable to fabricating the wide bandgap semiconductor because of its bandgap of 3.6 eV. In addition, SnO2 is commonly used as gas sensors. To fabricate high quality epitaxial SnO2 thin films, a powder sputtering method was used, in contrast to typical sputtering technique with sintered target. Single crystalline sapphire(0001) substrates were used. The samples were prepared with varying the growth parameters such as gas environment and film thickness. Then, the samples were characterized by using X-ray diffraction, scanning electron microscopy, and atomic force microscopy measurements. We found that the strain evolution of the samples was highly affected by gas environment and growth rate, resulted in the delamination under O2 environment.

• Journal of Ceramic Processing Research
• /
• v.19 no.5
• /
• pp.424-427
• /
• 2018

The effect of oxygen pressure in the synthesis of $SnO_2$ micro/nanocrystals through thermal evaporation of Sn powder was investigated. The thermal evaporation process was performed at $1000^{\circ}C$ for 1 hr under various oxygen pressures. The pressure of oxygen changed from 10 to 500 Torr. The morphology of $SnO_2$ crystals changed drastically with oxygen pressure. $SnO_2$ nanoparticles with an average diameter of 120 nm were formed at oxygen pressure lower than 10 Torr. $SnO_2$ nanowires were grown under an oxygen pressure of 100 Torr. The nanowires have diameters in the range of 100 ~ 500 nm and lengths of several tens of micrometers. As increasing the oxygen pressure to 500 Torr, the sizes of wires increased. A strong visible emission peak centered at about 500 ~ 600 nm was observed in the room temperature cathodoluminescence spectra of all the products.

• Applied Chemistry for Engineering
• /
• v.18 no.6
• /
• pp.650-653
• /
• 2007

$SnO_2$-doped $TiO_2$ powder was obtained from tin (IV) bis(acetylacetonate) dichloride and titanium diisopropoxide bis(acetylacetonate) with quinacridone as the dye sensitizer molecule. The structural changes of the reaction mixture were monitored by fourier transform infrared (FT-IR) spectroscopy. The morphology and microstructure of gel powder were studied by field-emission scanning electron microscopy (FE-SEM) and X-ray diffractometry (XRD). The photocatalytic activity of these powders with the anatase structure was investigated by using indigo carmine solution as a test dye

• Applied Chemistry for Engineering
• /
• v.17 no.5
• /
• pp.561-564
• /
• 2006

$SnO_{2}$-doped anatase type $TiO_{2}$ powder was prepared by the polymerization complex route from tin(IV) bis (acetylacetonate) dichloride, titanium diisopropoxide bis (acetylacetonate) and polyethylene glycol (PEG) as a complexing agent. The structural changes of reaction mixture were monitored by fourier transform infarared (FT-IR) spectroscopy. The microstructure and morphology of gel powder were studied by field-emission scanning electron microscopy (FE-SEM) and X-ray diffractometry (XRD). The photocatalytic activity of these powders with the anatase structure was investigated by using indigo carmine solution.

• Korean Journal of Materials Research
• /
• v.30 no.7
• /
• pp.338-342
• /
• 2020

Tin oxide (SnO₂) nanocrystals are synthesized by a thermal evaporation method using a mixture of SnO₂ and Mg powders. The synthesis process is performed in air at atmospheric pressure, which makes the process very simple. Nanocrystals with a belt shape start to form at 900 ℃ lower than the melting point of SnO₂. As the synthesis temperature increases to 1,100 ℃, the quantity of nanocrystals increases. The size of the nanocrystals did not change with increasing temperature. When SnO₂ powder without Mg powder is used as the source material, no nanocrystals are synthesized even at 1,100 ℃, indicating that Mg plays an important role in the formation of the SnO₂ nanocrystals at temperatures as low as 900 ℃. X-ray diffraction analysis shows that the SnO₂ nanocrystals have a rutile crystal structure. The belt-shaped SnO₂ nanocrystals have a width of 300~800 nm, a thickness of 50 nm, and a length of several tens of micrometers. A strong blue emission peak centered at 410 nm is observed in the cathodoluminescence spectra of the belt-shaped SnO₂ nanocrystals.

• Transactions on Electrical and Electronic Materials
• /
• v.2 no.1
• /
• pp.22-26
• /
• 2001

ITO (Indium-tin-oxide) thin films were deposited on glass substrates by a dc magnetron sputtering system using ITO powder target. The methods of heat treatment are important factor to obtain high quality ITO films with low electrical resistivity and good optical transmittance. Therefore, both methods of the substrate temperature and post-deposition annealing temperature have been compared on the film structural, electrical and optical properties. A preferred orientations shifts from (411) to (222) peak at annealing temperature of 200$\^{C}$. Minimum resistivity of ITO film is approximately 8.7$\times$10$\^$-4/ Ωcm at substrate temperature of 450$\^{C}$. Optical transmittances at post annealing temperature above 200$\^{C}$ are 90%. As a result, the minimum value of annealing temperature that is required for the recrystallization of as-deposited ITo thin films is 200$\^{C}$.

• Korean Journal of Materials Research
• /
• v.21 no.1
• /
• pp.21-27
• /
• 2011

A nano-porous structure of tin oxide was prepared using an anodic oxidation process and the sample's electrochemical properties were evaluated for application as an anode in a rechargeable lithium battery. Microscopic images of the as-anodized sample indicated that it has a nano-porous structure with an average pore size of several tens of nanometers and a pore wall size of about 10 nanometers; the structural/compositional analyses proved that it is amorphous stannous oxide (SnO). The powder form of the as-anodized specimen was satisfactorily lithiated and delithiated as the anode in a lithium battery. Furthermore, it showed high initial reversible capacity and superior rate performance when compared to previous fabrication attempts. Its excellent electrode performance is probably due to the effective alleviation of strain arising from a cycling-induced large volume change and the short diffusion length of lithium through the nano-structured sample. To further enhance the rate performance, the attempt was made to create porous tin oxide film on copper substrate by anodizing the electrodeposited tin. Nevertheless, the full anodization of tin film on a copper substrate led to the mechanical disintegration of the anodic tin oxide, due most likely to the vigorous gas evolution and the surface oxidation of copper substrate. The adhesion of anodic tin oxide to the substrate, together with the initial reversibility and cycling stability, needs to be further improved for its application to high-power electrode materials in lithium batteries.

• Journal of Electrical Engineering and Technology
• /
• v.6 no.3
• /
• pp.414-417
• /
• 2011

Indium tin oxide (In:$SnO_2$) nanoparticles were synthesized employing a sol-gel combustion method followed by annealing. The TG, XRD, XPS and SEM results of the precursor powders and calcinated In:$SnO_2$ nanoparticles were investigated. Crystal structures were examined by powder XRD, and those results show shaper intensity peak at $25.6^{\circ}$ ($2{\theta}$) of $SnO_2$ by increased annealing temperature. A particle morphology and size was examined by SEM, and the size of the nanoparticles was found to be in the range of 20~30nm. In:$SnO_2$ films could controlled by nanoparticle material at various annealing temperature. The sol-gel combustion method was offered simple and effective route for the synthesis of In:$SnO_2$ nanoparticles.

• Journal of Powder Materials
• /
• v.9 no.1
• /
• pp.38-42
• /
• 2002

Effects of chemical compositions on the sintering behavior of the lead borosilicate glass developed for barrier ribs of plasma display panels were investigated in this study. Formation of pores during sintering of the glass was noted and their formation mechanism was investigated using XPS, TG/DTA, and XRD. The results indicated that pores are formed by the oxygen released from Pb-oxides during sintering.

• Journal of the Korean Electrochemical Society
• /
• v.1 no.1
• /
• pp.24-27
• /
• 1998

Electroluminescence (EL) comes from the light emission obtained by the electrical excitation energy passing through a phosphor layer undo. an applied high electrical field $(10^6 V/cm)$. The preparation of white and blue phosphors and characterizations of light emitting alternating current powder electroluminescent devices (ACPELDs) were investigated. In this work, we fabricated two kinds of ELDs, that is, yellow electroluminescent device (B-ELD), blue electroluminescent device (B-ELD). The basic st.uctures of Y-ELD and B-ELD are ITO (Indium Tin Oxide)/phosphor layer/Insulator layer/Carbon electrode and ITO/Phosphor layer/Insulating layer/carbon electrode, respectively. Another structures of ITO/Phosphor and Insulator mixture layer/Backelectrode are introduced. EL spectra and luminance of two types of ELDs were measured by changing voltage at fixed frequency 0.4kHz, 1.5kHz. Blue and yellow phosphors prepared in this work show $50cd/m^2\;and\;30cd/m^2$ of luminance at 400Hz, 150V.