• Journal of electromagnetic engineering and science
• /
• v.18 no.1
• /
• pp.20-28
• /
• 2018

The time synchronization of each sub-unit of a pulsed generator is important to generate an output high-power radio frequency (RF) signal. To obtain the time synchronization between an input RF signal fed by an external source and an electron beam produced by an electric pulse generator, the influence of different charging voltages on a delay and a rise time of the output pulse waveform in the electric pulse generator should be carefully considered. This paper aims to study the timing characteristics of the delay and the rise time as a function of different charging voltages with a peak value of less than -35 kV in the high-voltage pulse generator, including a trigger generator (TG) and a pulse-forming line (PFL). The simulation has been carried out to estimate characteristics in the time domain, in addition to their output high-voltage amplitude. Experimental results compared with those obtained by simulation indicate that the delay of the output pulses of the TG and PFL, which are made by controlling the external triggering signal with respect to different charging voltages, is getting longer as the charging voltage is increasing, and their rise times are inversely proportional to the amplitude of the charging voltage.

• Journal of IKEEE
• /
• v.8 no.1 s.14
• /
• pp.39-46
• /
• 2004

This paper presents the realization schemes for a multipurpose coherent mono-pulse radar Simulator with extendable features. We developed and installed the TSG(Timing Signal Generator) board which can simulate a mechanically rotate signal of antenna, an operation timing signal of pulse radar and target signal, to operate the simulator without real target in the indoor environment. Also, with the insertion of the radar signal processor, it came to be easy to achieve the addition of radar function algorithms, to rebuild or extend the multi-DSP Architecture into the simulator. Throughout the simulation results, we verified that the designed coherent mono-pulse radar simulator can exactly display a moving target on the realistic monitor(RD 9800).

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.591-599
• /
• 2001

The paper identifies a severe form of core saturation instability in an DC/AC interaction system. It then seeks solutions to the problem by HVDC control means. This is achieved by a proper design of the Voltage Dependent Current Order Limiter (VDCOL), the Current Regulator and Timing Pulse generator. Supplementary control loops have also been introduced to result in a satisfactory performance as compared to that obtained one with the use of uncharacteristic harmonic filter on the AC side. Robustness of all the options has been demonstrated through recovery performance of the DC link in response to both I-phase and 3-phase 5 cycle faults on both rectifier and inverter commutating buses.

• Journal of Power Electronics
• /
• v.2 no.4
• /
• pp.297-304
• /
• 2002

The paper identifies a severe form of core saturation instability in a DC/AC interaction system. It then seeks solutions to the problem by HVDC control means. This is achieved by a proper design of the Voltage Dependent Current Order Limiter (VDCOL), the Current Regulate. and Timing Pulse generator. Supplementary control loops have also been introduced to result in a satisfactory performance as compared to that obtained one with the use of uncharacteristic harmonic filter on the AC side. All the options have been demonstrated through recovery performance of the DC link in response to both 1-phase and 3-phase 5 cycle faults on both rectifier and inverter commutating buses.

• Journal of Advanced Navigation Technology
• /
• v.11 no.2
• /
• pp.163-169
• /
• 2007

In this paper, we propose a method of trigger pulse generation to capture the image on time by making a synchronization between the x-ray generator and digital x-ray image acquisition system. we designed a wireless trigger pulse generation circuit to make a synchronization between x-ray generator and digital image acquisition system and analysis its performance. When it starts to detect a certain level of x-ray radiation or above from the air, this method starts to generate a ACQ_START signal to indicate the timing for image acquisition starting from digital image acquisition system. Hence, when it starts to detect under certain level of x-ray signal from the air, this method starts to generate a ACC_END signal to indicate the timing for image acquisition stop from digital image acquisition system. Image acquisition is activated only this time between ACQ_START and ACQ_END signal. By doing this wireless detecting of x-ray signal from remote, we can get more accurate timing for capturing the x-ray image and any type of x-ray generator can be connected to digital image acquisition system, regards of wired protocol. This makes easy installation. We could get 3.5 line pair / mm resolution at 20 mAs of x-ray level with resolution chart. This is same or better image comparing to conventional wired result.

• Journal of Sensor Science and Technology
• /
• v.22 no.1
• /
• pp.84-88
• /
• 2013

In this paper, the low price signal generator with capability of frequency high-resolution and variable sync pulse has implemented. It fulfils well the requirements for SS-OCT of the frequency resolution less than 1Hz, frequency stability of ${\leq}{\pm}0.5Hz$/10 min and variable sync pulse output timing. Through its performance test applied to wavelength swept laser, 120 nm sweeping range and 10 mW average optical power were obtained. This shows that the realized sine-wave generator can replace the commercial high cost and high performance signal generators employed by current SS-OCT systems.

• Journal of Biosystems Engineering
• /
• v.12 no.1
• /
• pp.45-52
• /
• 1987

In order to improve the thermal efficiency of an internal combustion engine, various ignition timing control systems were examined and the best one was chosen. The parts used for the systems were a microcomputer system with DAS, 8 bit output port (D-FLIP FLOP), three types of isolation circuit, two types of ignition timing pulse generator, three types of switching circuit and two types of high voltage ignition circuit. Most systems did not operate well due to the effects of electromagnetic waves and surge currents occurring when the ignition began or ended with resulting high voltage. The best ignition timing control system was found to be the combination of (microcomputer system)-(ignition timing pulse generator using step motor position control pick-up)-(switching circuit using TR logic)-(high voltage ignition circuit using CDI).

• Journal of IKEEE
• /
• v.9 no.2 s.17
• /
• pp.136-142
• /
• 2005

This paper describes some major schemes for developing timing signal generator which can be used for testing of 3D radars. The developed generator has a function not only to simulate information on elevation angle for the simulated target signals but also to generate a modulated signal up to 80MHz. Because this generator has an internal modulating function instead of an external modulating function and has sufficient memory enough to change the parameters according to operating programs, it realization of various test-environments for testing a radar can be made with easy and with low expense.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.1
• /
• pp.98-105
• /
• 2007

In this paper, we propose a timing detector using suboptimal maximum likelihood method. The proposed method has an simple reference signal generator. Additionally, timing detector's gain of the proposed method is the same to Early-Late gate and ML method. We reveal that tracking range of time tracker is narrow because of using data-decision, that is, tracking range is ${\pm}0.06ns$ for the 4-order Gaussian monocycle with 0.7ns pulse width. Therefore we can find that searcher must have very accurate acquisition procedure. When estimating a performance of time tracker, we consider a jitter in transmitter and receiver's pulse generation process as well as background noise. By using computer simulation, we propose mean/variance of timing detector and tracking process. Also we consider a mobility in tracking process, i.e., timing error modeled ramp function. In order to propose a performance of time tracker, we consider only one correlation demodulator.

• Journal of Sensor Science and Technology
• /
• v.27 no.1
• /
• pp.64-67
• /
• 2018

A new CMOS neuron circuit for implementing bistable synapses with spike-timing-dependent plasticity (STDP) properties has been proposed. In neuromorphic systems using STDP properties, the short-term dynamics of the synaptic efficacies are governed by the relative timing of the pre- and post-synaptic spikes, and the efficacies tend asymptotically to either a potentiated state or to a depressed one on long time scales. The proposed circuit consists of a negative shifter, a current starved inverter and a schmitt trigger designed using 0.18um CMOS technology. The simulation result shows that the proposed circuit can reduce the total size of neurons, and the spike energy of the proposed circuit is much less compared to the conventional circuits.