• Journal of Environmental Impact Assessment
• /
• v.27 no.6
• /
• pp.658-673
• /
• 2018

Social conflicts with extremely low frequency magnetic field(ELF-MF) exposures are expected to exacerbate due to continued increase in electric power demand and construction of high voltage transmission lines(HVTL). However, in current environmental impact assessment(EIA) act, specific guidelines have not been included concretely about EIA of ELF-MF. Therefore, this study conducted a standardization study on EIA method through case analysis, field measurement, and expert consultation of the EIA for the ELF-MF near HVTL which is the main cause of exposures. The status of the EIA of the ELF-MF and the problem to be improved are derived and the EIA method which can solve it is suggested. The main contents of the study is that the physical characteristics of the ELF-MF affected by distance and powerload should be considered at all stages of EIA(survey of the current situation - Prediction of the impacts - preparation of mitigation plan ? post EIA planning). Based on this study, we also suggested the 'Measurement method for extremely low frequency magnetic field on transmission line' and 'Table for extremely low frequency magnetic field measurement record on transmission line'. The results of this study can be applied to the EIA that minimizes the damage and conflict to the construction of transmission line and derives rational measures at the present time when the human hazard to long term exposure of the ELF-MF is unclear.

• Journal of agricultural medicine and community health
• /
• v.44 no.1
• /
• pp.11-27
• /
• 2019

Dementia is major epidemic disease of the 21st century in the world. Dementia is one of the major issues in public health globally. Also in Korea, the estimated prevalence of dementia was 8.7%(0.47 million) in 2010, the number will reach the 1 million mark in 2024, it will become a 15.1%(2.71 million) by 2050. Among Koreans aged 65 or older, 725,000 are estimated to be suffering from dementia in 2017. Against dementia, Korea developed three National Dementia Plans in 2008, 2012, and 2016. The 1st plan was came into effect in 2008 and focused on prevention, early diagnostic, development and coordination of infrastructures and management, and improving awareness. The 2nd plan was launched in 2012, addressed the same priorities but had a stronger focus on supporting family members. In 2012 the Dementia Management Act established a statutory basis for organization of the National Dementia Plans. Under the Dementia Management Act, the government is required to produce a comprehensive plan for dementia every 5 years. The Act also orders that the government should register the dementia patients and collect statistics on epidemiology and the management of the dementia conditions. The Dementia Management Act of Korea required the operation of the National Institute of Dementia and Metropolitan/Provincial Dementia Centers to make and carry out dementia management plans throughout the nation. The Act also mandate to establish Dementia Counselling Centers in every public health center and the National Dementia Helpline. The 3rd National Dementia Plan of 2016 aims to build a dementia friendly community to ensure people with dementia and their carer live well. This plan focus on community-based prevention and management of dementia, convenient and safe diagnosis, treatment, and care for people with dementia, the reduction of the care burden for family care-givers of people with dementia, and support for dementia research through research, statistics and technology. In 2017, Moon's government will introduce the "National Dementia Responsibility System," which guarantees most of the burden caused by dementia. This plan include that the introduction of a ceiling on self-pay for dementia diseases, expansion of the application of dementia care standards through alleviating the support criteria for long-term care insurance for mild dementia, expansion of dementia support centers, expansion of national and public dementia care facilities. In the meantime, Korea has accomplished many accomplishments by establishing many measures related to dementia and promoting related projects in a short time, but there are still many challenges.

• Korean Journal of Heritage: History & Science
• /
• v.46 no.3
• /
• pp.94-113
• /
• 2013

Donggwanwangmyo[East Shrine of King Guan Yu] is the shrine for General Guan Yu from the Shu Dynasty, China. This type of shrine was begun to be built from the Tang Dynasty in China and from 1598 in Korea when the Japanese invaded Korea for the $2^{nd}$ time. Donggwanwangmyo is historically significant because it was jointly constructed by China and Korea in the spring of 1602 after the end of Japanese invasion of Korea. However, almost no research has been conducted about the sculptures standing at Donggwanwangmyo and there are many mistakes concerning the names and materials of these sculptures. This study is conducted to resolve these issues as follows: First of all, it was found that the main building of Donggwanwangmyo enshrines those which were moved from the North Shrine of Guan Yu and the West Shrine of Guan Yu during the Japanese colonial rule of Korea in addition to what was initially placed in Donggwanwangmyo during construction. These relics are assorted and each line of them is displayed in the center and to the east or west of the building. Among the relics, seven sculptures are standing at the center of the main building, among which one sculpture of Guan Yu is made of gold and two sculptures of maids and four sculptures of guards are made of clay. It is particularly noted that the sculptures of Guan Yu and his guards, Guan Ping, Zhou Cang, Wang Fu, and Zhao Lei, represent the portraits of historical characters that actually existed. Moreover, the sculptures of guards are characterized by the fact that they are unlike those in China, but have two pairs of literary men and warriors that stand facing each other as is the case in the royal mausoleums constructed during the Joseon Dynasty. Second of all, the sculptures from Donggwanwangmyo were carved in 1602, but their costumes and equipment were derived from the paintings from the Tang and Song Dynasties. Some decorations from the Ming Dynasty are also reflected in the sculptures. It implies that Donggwanwangmyo was partially modeled after the Shrine of Emperor Guan Yu[Gwanjemyo] in Jiezhou which was rebuilt in 1593 by Emperor Sinjong of the Ming Dynasty and that the secular and dramatic patterns of the Qing Dynasty are prevalent in the said sculptures based on the patterns of the Ming Dynasty because all the sculptures at the Shrine in Jiezhou were constructed when the Qing Dynasty ruled between the $18^{th}$ and the $19^{th}$ Centuries. In conclusion, it was found that sculptures from Donggwanwangmyo were created in 1602, that they follow the ancient traditions attested by the paintings of Korean and Chinese sculptures, and that they are very valuable in art history since they retain the original forms of the Shrine of Guan Yu built during the Joseon and Ming Dynasties.

• Science of Emotion and Sensibility
• /
• v.21 no.4
• /
• pp.63-76
• /
• 2018

The purpose of this study was to investigate the effect of contact type textile electrode structure on heart activity signal acquisition for smart healthcare. In this study, we devised six contact type textile electrodes whose electrode size and configuration were manipulated for measuring heart activity signals using computerized embroidery. We detected heart activity signals using a modified lead II and by attaching each textile electrode to the chest band in four healthy male subjects in a standing static posture. We measured the signals four times repeatedly for all types of electrodes. The heart activity signals were sampled at 1 kHz using a BIOPAC ECG100, and the detected original signals were filtered through a band-pass filter. To compare the performance of heart activity signal acquisition among the different structures of the textile electrodes, we conducted a qualitative analysis using signal waveform and size as parameters. In addition, we performed a quantitative analysis by calculating signal power ratio (SPR) of the heart activity signals obtained through each electrode. We analyzed differences in the performance of heart activity signal acquisition of the six electrodes by performing difference and post-hoc tests using nonparametric statistic methods on the calculated SPR. The results showed a significant difference both in terms of qualitative and quantitative aspects of heart activity signals among the tested contact type textile electrodes. Regarding the configurations of the contact type textile electrodes, the three-dimensionally inflated electrode (3DIE) was found to obtain better quality signals than the flat electrode. However, regarding the electrode size, no significant difference was found in performance of heart signal acquisition for the three electrode sizes. These results suggest that the configuration method (flat/3DIE), which is one of the two requirements of a contact type textile electrode structure for heart activity signal acquisition, has a critical effect on the performance of heart activity signal acquisition for wearable healthcare. Based on the results of this study, we plan to develop a smart clothing technology that can monitor high-quality heart activity without time and space constraints by implementing a clothing platform integrated with the textile electrode and developing a performance improvement plan.

• Korean Journal of Environment and Ecology
• /
• v.33 no.3
• /
• pp.303-320
• /
• 2019

Plants interact with various biotic and abiotic environmental factors. It requires much information to understand the traits of a plant species. A shortage of information would restrict the assessment, especially in the evaluation of what kind of factors influence a plant species to face extinction. Polygonatum stenophyllum Maxim. is one of the northern plants of which Korea is the southern distribution edge. The Korean Ministry of Environment had designated it to be the endangered species until December 2015. Although it is comparatively widespread, and a large population has recently been reported, it is assessed to be vulnerable due to the low population genetic diversity. This study evaluated the current distribution of Polygonatum stenophyllum Maxim. We investigated the vegetational environment, population structures, phenology, soil environment, and self-incompatibility based on the results. Lastly, we evaluated the current threats observed in the habitats. The habitats tended to be located in the areas where the masses at the edge of the stream accumulated except for those that were located on slopes of some mountainous areas. Most of them showed a stable population structure and had re-established or recruited seedlings. Polygonatum stenophyllum Maxim. had the difference in time when the shoots appeared above the ground depending on the depth of the rhizome located in the underground. In particular, the seedlings and juveniles had their rhizome located shallow in the soil. Visits by pollinator insects and success in pollination were crucial factors for bearing of fruits by Polygonatum stenophyllum Maxim. The threats observed in the habitat of Polygonatum stenophyllum Maxim. included the expansion of cultivated land, construction of new buildings, and construction of river banks and roads. Despite such observed risk factors, it is not likely that there would be rapid population reduction or extinction because of its widespread distribution with the total population of more than 2.7 million individuals and the new populations established by the re-colonization.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.21 no.3
• /
• pp.135-145
• /
• 2019

Analysis of a long cycle or a trend of time series data based on a long-term observation would require comparability between data observed in the past and the present. In the present study, we proposed an approach to ensure the compatibility among the instruments used for the long-term observation, which would allow to secure continuity of the data. An open-path gas analyzer (Model LI-7500, LI-COR, Inc., USA) has been used for eddy covariance flux measurement in the Gwangneung deciduous forest for more than 10 years. The open-path gas analyzer was replaced by an enclosed-path gas analyzer (Model EC155, Campbell Scientific, Inc., USA) in July 2015. Before completely replacing the gas analyzer, the carbon dioxide ($CO_2$) and latent heat fluxes were collected using both gas analyzers simultaneously during a five-month period from August to December in 2015. It was found that the $CO_2$ fluxes were not significantly different between the gas analyzers under the condition that the daily mean temperature was higher than $0^{\circ}C$. However, the $CO_2$ flux measured by the open-path gas analyzer was negatively biased (from positive sign, i.e., carbon source, to 0 or negative sign, i.e., carbon neutral or sink) due to the instrument surface heating under the condition that the daily mean temperature was lower than $0^{\circ}C$. Despite applying the frequency response correction associated with tube attenuation of water vapor, the latent heat flux measured by the enclosed-path gas analyzer was on average 9% smaller than that measured by the open-path gas analyzer, which resulted in >20% difference of the sums over the study period. These results indicated that application of the additional air density correction would be needed due to the instrument heat and analysis of the long-term observational flux data would be facilitated by understanding the underestimation tendency of latent heat flux measurements by an enclosed-path gas analyzer.

• Korean Journal of Heritage: History & Science
• /
• v.52 no.3
• /
• pp.112-129
• /
• 2019

This study investigates the influence and implications of the supervised process of production of flower vessels (花器) in 1411. The type, the production method, and the purpose of flower vessels (花器) were determined based on the workshops appearing in King Sejong-Sillok, Chiriji ("世宗實錄" "地理志") and Gyeongsang-do Chiriji ("慶尙道地理志"), considering articles excavated from Sangju kiln sites. In addition, the implications and the starting point of production of flower vessels (花器) in the Joseon Dynasty were identified. During the Joseon Dynasty, an effort was made to reorganize the government offices, to align ritual systems in the early 15th century. Preparation for rituals, preparation of supplemental utensils used in ancestral rites (祭器), the construction of architecture related to the Royal Family, and the production of weaponry (武器) were supervised. In 1411, flower vessels (花器) had a preferred supervised process of production as well, which means being recognized as a subject of maintenance for the Joseon Dynasty's aims. Flower vessels (花器) had been produced using grayish-blue powdered celadon (粉靑沙器) as flower pots (花盆), and as celadon flower pot-support (花臺), at Sangju kiln sites in particular, since 1411. Interestingly, products had been manufactured in royal kilns as well as in a few other kilns similar to the supervised process of production of flower vessels (花器) in the middle of the 15th century. It means that this effected the Gyeon-yang (見樣) supervised process of flower vessel (花器) production in 1411. At that time, the Joseon Dynasty used Gyeon-yang (見樣) for imperial gifts for the Ming Dynasty and on separate manufactured articles to ensure the standards of production. Gyeon-yang (見樣) affected the production of ceramic utensils used in ancestral rites (祭器), and government officials in Saongwon (司饔院) supervised the production of ceramics for the Royal Family year after year. In sum, it was flower vessels (花器) using Gyeon-yang (見樣) that provided precise production rules to supervise the process of production in 1411.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.47 no.3
• /
• pp.1-11
• /
• 2019

The purpose of this study is to propose a sustainable village-unit urban regeneration plan for the Ewha Mural Village, where mural artists recovered concrete fences to be followed by some residents damaging the mural paintings. Through a review of the existing literature and a preliminary survey, we derived the urban regeneration factors (environmental sustainability, economic sustainability, and social sustainability) applicable at the village level. After an empirical survey on the residents, we tried to identify various problems of the Ewha Mural Village. Residents selected the factors of accessibility, parking management, diversity of industries, creation of new jobs, community participation of residents for the mural village's activation, and stable living spaces. In the case of Ewha Mural Village, physical environment factors for the residents at the time of construction were not considered and the village was mainly planned using budget-based murals. Since then, the inequality of economic benefits intensified the conflicts among the residents. In addition, public benefits, such as establishing new industries and employing outsiders, were not provided, and these facts appear to have led to an unsustainable murals village, in which the murals that are the protagonists of the village revitalization are being destroyed. Therefore, the urban regeneration of Ewha Mural Village should be designed considering a region where some residential areas can be transformed into tourist areas. In addition, it is essential to employ a win-win method to improve the living environment, such as road maintenance, not only partial economic benefits, such as increased land-value, and to increase resident's value as a common asset within the village itself.

• Journal of the Korean Society of Radiology
• /
• v.13 no.4
• /
• pp.653-659
• /
• 2019

The purpose of this study is to measure the (air dose rate of radiation dose) the discharged patient who was administrated high dose $^{131}I$ treatment, and to predict exposure radiation dose in public person. The dosimetric evaluation was performed according to the distance and angle using three copper rings in 30 patients who were treated with over 200mCi high dose Iodine therapy. The two observer were measured using a GM surverymeter with 8 point azimuth angle and three difference distance 50, 100, 150cm for precise radion dose measurement. We set up three predictive simulations to calculate the exposure dose based on this data. The most highest radiation dose rate was showed measuring angle $0^{\circ}$ at the height of 1m. The each distance average dose rate was used the azimuth angle average value of radiation dose rate. The maximum values of the external radiation dose rate depending on the distance were $214{\pm}16.5$, $59{\pm}9.1$ and $38{\pm}5.8{\mu}Sv/h$ at 50, 100, 150cm, respectively. If high dose Iodine treatment patient moves 5 hours using public transportation, an unspecified person in a side seat at 50cm is exposed 1.14 mSv radiation dose. A person who cares for 4days at a distance of 1 meter from a patient wearing a urine bag receives a maximum radiation dose of 6.5mSv. The maximum dose of radiation that a guardian can receive is 1.08mSv at a distance of 1.5m for 7days. The annual radiation dose limit is exceeded in a short time when applied the our developed radiation dose predictive modeling on the general public person who was around the patients with Iodine therapy. This study can be helpful in suggesting a reasonable guideline of the general public person protection system after discharge of high dose Iodine administered patients.

• Management & Information Systems Review
• /
• v.38 no.1
• /
• pp.23-41
• /
• 2019

Smart Factory is different from existing factory automation in that it aims to produce personalized products with minimum time and cost through ICT. However, previous researches, not from consumers but from product suppliers, have focused on technology trends and technology application methods. In order for Smart Factory to be successful, it must go beyond supplier-focus to meet the needs of consumers. In this study, we surveyed the purchase intention of the personalized product manufactured by smart factory. Influencing factors of purchase intention were drawn as consumers' need for uniqueness, innovativeness, need for touch, and privacy concern, based on previous research. As results of data analysis, it was confirmed that respondents were willing to purchase personalized products, and that consumers' need for uniqueness, innovativeness, and need for touch had a significant impact on purchase intention of personalized products. Our findings can be summarized as follows. First, Consumers' need for uniqueness was found to have positive effects(${\beta}=0.168$) on purchase intention of personalized products. The desire to differentiate themselves from others will be reflected in their personalized products. Therefore, consumers with a higher desire for uniqueness tend to be more willing to purchase personalized products. Second, consumer innovativeness was found to have positive effects(${\beta}=0.233$) on purchase intention of personalized products. Personalized shoes suggested in this study is a new type of personalized product that is manufactured by the latest information and communication technologies such as multi-function robots and 3D printing. Therefore, consumers seeking innovative new experiences are more willing to purchase personalized products. Third, need for touch was found to have positive effects(${\beta}=0.299$) on purchase intention of personalized products. In a smart factory environment, prosuming participation is given to consumers. If consumers participate in the product development process and reflect their requirements on the product, they are expected to increase their purchase intention by virtually satisfying the need for touch. Fourth, privacy concern was found to have no significantly related to purchase intention of personalized products. This is interpreted as a willingness to tolerate the risk of exposing personal information such as home address, telephone number, body size, and preference for consumers who feel highly useful in personalized products.