• The Transactions of the Korean Institute of Power Electronics
• /
• v.24 no.3
• /
• pp.139-146
• /
• 2019

As the number of electric vehicles (EVs) in Jejudo Island increases, the secondary use of EV batteries is becoming increasingly mandatory not only in reducing greenhouse gas emissions but also in promoting resource conservation. For the secondary use of EV batteries, their capacity and performance at the end of automotive service should be evaluated properly. In this study, the battery state information from the on-board diagnostics or OBD2 port was acquired in real time while driving three distinct routes in Jejudo Island, and then the battery operating characteristics were assessed with the driving routes. The route with higher altitude led to higher current output, i.e., higher C-rate, which would reportedly deteriorate state of health (SOH) faster. In addition, the SOH obtained from the battery management system (BMS) of a 2017 Kia Soul EV with a mileage of 55,000 km was 100.2%, which was unexpectedly high. This finding was confirmed by the SOH estimation based on the ratio of the current integral to the change in state of charge. The SOH larger than 100% can be attributed to the rated capacity that was lower than the nominal capacity in EV application. Therefore, considering the driving environment and understanding the SOH estimation process will be beneficial and necessary in evaluating the capacity and performance of retired batteries for post-vehicle applications.

• Journal of Biosystems Engineering
• /
• v.32 no.6
• /
• pp.455-461
• /
• 2007

The electric current of a flow injection type enzyme-sensor was measured to confirm the stable operating conditions of the sensor. The current of the sensor was decreased as the buffer solution velocity increased. Under the limitation of the cycle time to be below 10 minutes, the effective ranges of the buffer solution velocity were suggested $0.10{\sim}0.26$, $0.12{\sim}0.24$, $0.1{\sim}0.25$ and $0.05{\sim}0.10\;cm/s$ of 1.0, 1.4, 2.4 and 3.4 mm of the electrode diameters, respectively. As the reaction time of the enzyme and the substrate was increased, the current was decreased because of the dilution between the sample and buffer solution. Therefore, it could be recommended that the reaction time was able to be selected as shortly as possible in consideration of the total cycle time. As the result of the experiments using a different volume ratio of the enzyme to substrate, it was concluded that the substrate had to be mixed with the same amount of the enzyme. The current have increased remarkably in proportion to the electrode diameter under 0.1 cm/s of the buffer solution velocity but there was no difference over 0.1 cm/s of the buffer solution velocity. The cross type arrangement of the electrode was highly suggested for application and machining of the sensor.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.5
• /
• pp.659-663
• /
• 2012

The application of large power transformer into a power distribution system was inevitable due to the increase of power demand and distributed generation. However, the decrease of the power transformer's impedance caused the short-circuit current of the power distribution system to be increase thus, the higher short-circuit current exceeded the cut-off ratings of the protective devices such as circuit breaker. To solve these problems, several countermeasures have been proposed to protect the power system effectively from higher fault current and the superconducting fault current limiter (SFCL) has been expected to be the promising countermeasure. In spite of excellent current limiting performances of the SFCL, on the other hand, the efforts to apply the SFCL into power system has been delayed due to both the limited spaces for the SFCL's installation and its long recovery time after the fault removal. In order to solve these problems, a hybrid SFCL, which can perform either first half cycle limiting of first half cycle non-limiting operation, has been developed by corporation of LSIS (LS Industrial System) and KEPCO (Korea Electric Power Corporation). In this paper, we tried to requirements hybrid SFCL by PSCAD/EMTDC. Simulation results of our analysis of the hybrid SFCL is that its accompanied the characteristics both the limit the fault current and quick recovery caused by the less impact from superconductor.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.8
• /
• pp.1374-1381
• /
• 2010

This paper discusses the characteristics of sheath circulating current as well as the development and application of new software for underground power cable systems. Generally, in steady state, high sheath circulating current causes the increase of sheath temperature and thermal resistance which leads to the steeply reduction of the power capacity. Therefore, the exact calculation of sheath circulating current is required for analysis about the influence of high sheath current on permissible current. In this paper, Power Cable Simulator is developed for calculation of the sheath current. It can analyse the sheath current by real time. It is also easier to use than conventional software, such as EMTP and CabSim, because all the data for calculating the cable parameters are stored in a database(DB) within Power Cable Simulator. In addition, the accuracy of Power Cable Simulator is also proved through the comparison among the current calculated by Power Cable Simulator, EMTP and Cabsim with measured current.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.711-712
• /
• 2006

For the application of superconducting fault current limiters(SFCLs) to the protection system, quench recovery characteristics of Au/YBCO thin film were investigated. The Au/YBCO thin film was designed as a SFCL element with a bi-spiral pattern. The SFCL element limited the fault current successfully. For the analysis of the recovery to superconducting state, we measured resistance variation of the SFCL element after the quench. In addition, in order to investigate the dependence of quench characteristics of SFCL on the $LN_2$ cooling condition, we measured the recovery time under a pressure of 1, 2 and 3 atm. As the results, the recovery time increased in proportion to the duration of the fault currents. In the sub-cooled condition, while the quench development was exactly the same, the recovery time was shortened as the pressure increased.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.252-252
• /
• 2000

The Resistance Spot Welding (RSW) has been considered as an inherently safe and reliable method far joining metals, and has been widely employed, especially in automobile body assembly shops, as a manufacturing process. In recent years, the requirement for more sophisticated quality control procedures has considerably grown in the mass production industries. The object of the application of servo control to spot welding gun is the improvement of quality control in the spot welding, one of conventional industrial areas. The important factors affecting welding qualities (shear strength, nuggest size, indentation depth) are welding current, welding time, and gun press force. Welding current and welding time are controlled by welding timer. But, the conventional welding guns using compressed air are out of control in changing gun press forces in welding process. In this paper, a servo gun welding system having a AC servo motor and a PC control system is presented. The main object of this paper is to estimate the influence of gun press force changes in the welding process (press time -> welding time -> hold time) to welding qualities, and to evaluate welding qualities in real time, by recognizing the patterns of gun press forces changed in the welding process and comparing with the standard patterns.

• 제어로봇시스템학회:학술대회논문집
• /
• 1990.10a
• /
• pp.663-668
• /
• 1990

This paper deals with the application of a Generalized Predictive Control (CPC) to a Pressurized Water Reactor (P.W.R) Nuclear Power Plant. Generalized Predictive Control is a sort of Explicit Self-Tuning Control. Current self-tuning algorithms lack robustness to prior choices of either dead-time (input time delay of a plant) or model order. GPC is shown by simulation studies to be superior to accepted self-tuning techniques such as minimum variance and pole-placement from the viewpoint that it is robust to prior choices of dead-time or model order. In this paper a GPC controller is designed to control the P.W.R. nuclear power rlant with varying dead-time and through the designing procedure the designer is free from the constraint of knowing the exact dead-time. The controller is constructed based on the 2nd order linear model approximated in the vicinity of operating point. To ensure that this low-order model describes the complex real dynamics well enough for control purposes, model parameters are updated on-line with a Recursive Least Squares algorithm. Simulation results are successful and show the possibilities of the GPC control application to actual plants with varying or unknown dead-time.

• Corrosion Science and Technology
• /
• v.12 no.2
• /
• pp.93-101
• /
• 2013

The object of this work is to establish an electrochemical noise(EN) measurement technique combined with a direct current potential drop(DCPD) method for monitoring of localized corrosion cracking of nickel-based alloy, and to analyze its mechanism. The electrochemical current and potential noises were measured under various conditions of applied stress to a compact tension specimen in a simulated primary water chemistry of a pressurized water reactor. The amplitude and frequency of the EN signals were evaluated in both time and frequency domains based on a shot noise theory, and then quantitatively analyzed using statistical Weibull distribution function. From the spectral analysis, the effect of the current application in DCPD was found to be effectively excluded from the EN signals generated from the localized corrosion cracking. With the aid of a microstructural analysis, the relationship between EN signals and the localized corrosion cracking mechanism was investigated by comparing the shape parameter of Weibull distribution of a mean time-to-failure.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.35C no.4
• /
• pp.50-59
• /
• 1998

This paper describes a 3.3V 8bit CMOS digital to analog converter (DAC) with two state current cell metrix architecture which consists of a 4 MSB and a 4 LSB current matrix stage. The symmetric two stage current cell matrix architecture allow the designed DAC to reduce hot only a complexity of decoding logics, but also a number of wider swing cascode curent mirros. The designed DAC with an active chip area of 0.8 mm$_{2}$ is fabricated by a 0.8 .mu.m CMOS n-well standard digital process. The experimental data shows that the rise/fall time, the settling time, and INL/DNL are6ns, 15ns, and a less than .+-.0.8/.+-.0.75 LB, respectively. The designed DAC is fully operational for the power supply down to 2.0V, such that the DAC is suitable for a low voltage and a low power system application. The power dissipation of the DAC with a single power supply of 3.3V is measured to be 34.5mW.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.747-750
• /
• 2002

A circuit building block for realizing a continuous-time active-only current-mode integrator is presented. The proposed integrator is composed only of internally compensated type operational amplifier (OA) and operational transconductance amplifiers (OTAs). The integrator is suitable for integrated circuit implementation in either bipolar or CMOS technologies, since it does not require any external passive elements. Moreover, the integrator gain can be tuned through the transconductance gains of the OTAs. Some application examples in the realization of current-mode network functions using the proposed current-mode integrator as an active element are also given.