• 한국세라믹학회지
• /
• 제36권9호
• /
• pp.991-996
• /
• 1999

Effect of solution property on the weight varation and microstructural change of film was studied by electrophoretic deposition in order to obtain a homogeneous and dense zirconia film. As a result of weight kinetics of film which obtained in alcohol or aqueous solution having different polarity experimental data showed large deviation from theoretical ones calculated by Zhang's kinetic model. It had been shown that the weight affecting factors was largely dependent on properties other than dielectric constant and viscosity of solvent zeta potential appiled field and time. In initial stage a main factor of the drastic weight increase was the capillary drag of porous substrate. The cause of weight decrease with time in aqueous solution after 300 s was attributed to the defect of film by sagging and electrolytic reaction. The electrolyte film which prepared in alcohol solution with good wetting for substrate had better homogeneous and dense microstructure than one in aqueous solution with high surface tension.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.II
• /
• pp.991-994
• /
• 2005

We have successfully commercialized a novel optical compensation film, OCB-WV film, for OCB-LCD-TVs which has fast response time and wide viewing angle. The OCB-WV film consists of a 45degree-aligned discotic layer and a high Rth biaxial TAC film, which is suited for a roll-to-roll polarizer manufacturing process. This OCB-WV has brought out the excellent features that OCB intrinsically has, making nextgeneration fast-response LCD-TVs possible and free from image blurring in conjunction with an impulsive driving scheme.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2000년도 제1회 학술대회 논문집
• /
• pp.207-208
• /
• 2000

The temporal response of the electroluminescence (EL) has been studied in the organic electroluminescent devices fabricated with a vacuum-deposited poly(p-phenylene) (PPP) thin film upon the application of a rectangular driving voltage. The blue EL emission arises with a delay time of several hundred nanoseconds and then saturates with the rise time of less than microsecond. The EL delay time is considered as the transit time of holes in the PPP thin film since the hole mobility is much larger than the electron mobility in PPP. The hole mobility is estimated to be ${\sim}$ $1{\times}10^{-5}$ $cm^2/Vs$ in the vacuum-deposited PPP film.

• 한국임상보건과학회지
• /
• 제7권1호
• /
• pp.1232-1237
• /
• 2019

Purpose. In this study, two types of soft contact lenses with different materials were selected to compare the time of tear film destruction and high order aberrations before and after wearing. Methods. Thirty patients (60 eyes) in their 20s were included in this study. Two lenses with different materials, Group 4 (Etafilcon A) and Group 5 (Narafilcon A) were selected. Using aberration analyzer and keratometry, high-order aberration and tear film test (NIF-BUT, NIAvg-BUT) were performed before and after wearing. Results. When comparing the higher aberrations of the Etafilcon A and Narafilcon A lenses, the higher aberrations of the Narafilcon A lens were higher overall. For the initial tear film break-up time (NIF-BUT) after wearing, the Etafilcon A lens was reduced by 4.0 seconds and the Narafilcon A lens increased by 0.6 seconds. For the mean tear film break-up time (NIAvg-BUT) after wearing, the Etafilcon A lens decreased by 2.4 seconds and the Narafilcon A lens increased by 1.7 seconds. Conclusions. NIF-BUT and NIAvg-BUT of Narafilcon A lens were increased. The lens with relatively low water content and higher oxygen permeability than the lens with high water content has relatively less tear evaporation, which means that the time of destruction of the tear film is increased.

• Imaging Science in Dentistry
• /
• 제31권1호
• /
• pp.17-22
• /
• 2001

Purpose: To compare the film density of Insight dental X-ray film (Eastman Kodak Co., Rochester, NY, USA) with that of Ektaspeed Plus film (Eastman Kodak) under manual and automatic processing conditions. Materials and Methods : Insight and Ektaspeed Plus films were exposed at three different exposure conditions with an aluminum step wedge on the films under the three different exposure times. The exposed films were processed by both manual and automatic ways. The Base plus fog density and the optical density made by exposing step wedge were calculated using a digital densitometer (model 07-443, Victoreen Inc, Cleveland, Ohio, USA). The optical densities of the Insight and Ektaspeed film versus thickness of alumimun wedge at the same exposure time were plotted on the graphs. Statistical analyses were applied for comparing the optical densities of the two films. Results: The film density of both Insight films and Ektaspeed Plus films under automatic processing condition was significantly higher over the manual processing. The film density of Insight films was significantly higher than that of Ektaspeed Plus films on both automatic and manual processing conditions. Conclusion: The radiation exposure time can be reduced when using Insight over Ektaspeed Plus film. To take the full advantage of reducing exposure time, Insight film should be processed automatically.

• Mass Spectrometry Letters
• /
• 제12권1호
• /
• pp.26-30
• /
• 2021

The impurity concentration is a crucial parameter for semiconductor thin films. Evaluating the impurity distribution in silicon thin film is another challenge. In this study, we have investigated the doping concentration of boron in silicon thin film using time of flight secondary ion mass spectrometry in dynamic mode of operation. Boron doped silicon film was grown on i) p-type silicon wafer and ii) borosilicate glass using hot wire chemical vapor deposition technique for possible applications in optoelectronic devices. Using well-tuned SIMS measurement recipe, we have detected the boron counts 101~104 along with the silicon matrix element. The secondary ion beam sputtering area, sputtering duration and mass analyser analysing duration were used as key variables for the tuning of the recipe. The quantitative analysis of counts to concentration conversion was done following standard relative sensitivity factor. The concentration of boron in silicon was determined 1017~1021 atoms/㎤. The technique will be useful for evaluating distributions of various dopants (arsenic, phosphorous, bismuth etc.) in silicon thin film efficiently.

• 한국염색가공학회지
• /
• 제22권4호
• /
• pp.362-372
• /
• 2010

This paper surveys the physical properties of the multiwall carbon nanotube (MWNT) and polyurethane composite film for improvement of mechanical properties and electrical characteristics. The modification of MWNT was carried out by acid treatment with nitric and sulphuric acid mixed solution, and then followed by thermal treatment for enhancing MWNT dispersion with polyurethane. This modified MWNT was mixed with polyurethane by changing the loading content of MWNT and dispersion time under the dimethylformamide solution in the ultrasonic wave apparatus. Various physical characteristics of the modified PU/MWNT films were measured and analyzed in terms of the loading content and dispersion time. The maximum absorbance of the PU/MWNT films were observed with the 2wt% loading at dispersion times of 2 and 24 hour, respectively. The minimum electrical volume resistivity of PU/MWNT film was shown at the loading content of 0.5wt% or more irrespective of dispersion treating time. However the optimum condition was assumed to 2wt% loading at dispersion time of 2 hours by assessing the surface profile of the film using video microscope. The breaking stress and strain of the PU/MWNT film decreased with increasing loading content, but no change of physical properties was shown with increasing in dispersion time.

• Journal of Pharmaceutical Investigation
• /
• 제29권2호
• /
• pp.127-136
• /
• 1999

In order to eliminate demerits of conventional dosage forms, dipotassium glycyrrhizate was formulated as a slim mucoadhesive film type dosage form. The mucoadhesive drug layer gel containing dipotassium glycyrrhizate was prepared using $Noveon^{\circledR}$ AA-1, hydroxypropylcellulose-M, ethylcellulose N 100 and citric acid, and the protective layer gel by using ethylcellulose N 100, $Eudragit^{\circledR}$ RS and castor oil. The viscosity of drug layer gel of mucoadhesive film was enhanced as the increased amount of $Noveon^{\circledR}$ AA-1 or hydroxypropyl cellulose-M. The drug content was unifonnly $1160{\pm}14.6\;{\mu}g$, and was varied within 3.5%. The optimum film dosage form showed a good fluidity and malleability of drug layer, with 179 g of thickness, pH 5.7, 411 min of in vitro adhesion time and 172 g in gravity adhesive strength. The release time of drug from the mucoadhesive film was significantly shorter but was delayed when polymers such as ethylcellulose was added. From these results, the new mucoadhesive film may be effective for the treatment of aphthous stomatitis.

• 한국전기전자재료학회논문지
• /
• 제14권8호
• /
• pp.658-662
• /
• 2001

This paper describes on the fabrication and characteristics of hot-film type micro-flowsensors integrated with Pt-RTD(resistance thermometer device) and micro-heater on the SOI(Si-on-insulator) membrane and trench structures, in which MGO thin-film was used as medium layer in order to improve adhesion of Pt thin-film to SiO$_2$ layer. Output voltages increased due to increase of heat-loss from sensor to external. The output voltage was 250 nV at N$_2$ flow rate of 2000 sccm/min, heating power of 0.3 W. The response time($\tau$:63%) was about 42 msec when input flow was step-input. The results indicated that micro-flowsensors with the SOI membrane and trench structures have properties of a high-resolution and ow consume power.

• 소성∙가공
• /
• 제21권1호
• /
• pp.30-35
• /
• 2012

FIM(Film Insert Molding) is an innovative method of producing decorated parts for a wide range of products. Because it requires fewer steps when compared to conventional production methods, the time and cost of manufacturing high quality components can be reduced considerably. In this paper, the effects of processing conditions on the warpage of film-insert molded plate were investigated by using a design of experiments. The dominant factors affecting warpage were mold temperature and holding pressure. Warpage increased with the temperature difference between stationary mold and fixed one. Even when the mold temperature difference was zero, the plate with a film was bent after ejection such that the film side protruded. As holding pressure increased, warpage decreased significantly. In addition warpage increased with time increment for the film-insert molded plates.