• Nuclear Engineering and Technology
• /
• v.36 no.1
• /
• pp.12-23
• /
• 2004

In the present study a new measurement technique has been developed, which uses an ultrasonic transmission signal in order to identify the vertical two phase flow pattern. The ultrasonic measurement system developed in the present study not only provides the information required for the identification of vertical two phase flow patterns but also makes real time identification possible. Various vertical two phase flow patterns such as bubbly, slug, churn, annular flow etc. have been accurately identified with the present ultrasonic measurement system under atmospheric condition. In addition, the present test apparatus can practically simulate the ultrasonic propagation characteristics under high temperature and high pressure systems. Therefore, it is expected that the present ultrasonic flow pattern identification technique could be applicable to the vertical two phase flow systems under high temperature and high pressure conditions.

• Journal of information and communication convergence engineering
• /
• v.3 no.1
• /
• pp.18-22
• /
• 2005

This paper presents the analog adaptive phase-locked loop (PLL) architecture with a new adaptive bandwidth controller to reduce locking time and minimize jitter in PLL output for wireless communication. It adaptively controls the loop bandwidth according to the locking status. When the phase error is large, the PLL increases the loop bandwidth and reduces locking time. When the phase error is small, the PLL decreases the loop bandwidth and minimizes output jitters. The adaptive bandwidth control is implemented by controlling charge pump current depending on the locking status. A 1.28-GHz CMOS phase-locked loop with adaptive bandwidth control is designed with 0.35 $mu$m CMOS technology. It is simulated by HSPICE and achieves the primary reference sidebands at the output of the VCO are approximately -80dBc.

• Korean Journal of Applied Biomechanics
• /
• v.13 no.1
• /
• pp.173-184
• /
• 2003

The purpose of this study was to investigate the batting characteristics in elite baseball players. Seven skilled collegiate players hit the ball which was thrown by a pitching machine linearly and strongly to the center of the field. Time, velocity, angle and pound reaction force variables were measured by using high-speed video cameras and pound reaction force analyzer. The results were as follows: 1. The elite players finished their stride performance in a short time and they stayed longer in a swing phase. The increases in the range of trunk rotation were associated with the delay of the swing phase. 2. The 'take-back' phenomenon in the trunk was showed after the stride phase. 3. The down swing demonstrated powerful line drives. 4. Equivalent body weights were placed on both feet during the ready phase. 95% of the body weights were moved to the rear foot during the stride phase, whereas the body weights were driven to the front foot during the swing phase. 95% of the body weights were placed on the front foot at impact.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.11
• /
• pp.1398-1406
• /
• 2004

The nonlinear signals from an impedance meter for the area average void fraction in two-phase flow have been analyzed to construct a phase space trajectory. The pseudo phase space was constructed with the time delay and proper dimensions. The time delay and the embedding dimension were chosen by the average mutual information and by the false nearest neighborhood, respectively. The attractor-density-map of projected states was used to produce the two dimensional probability distribution functions (2D-PDF). Since the developed 2D-PDF showed clear distinction of the flow patterns, the flow regime identification was made with three rules and with the 2D-PDF. Also, the transition criteria of Mishima-Ishii agree well with the present results.

• Journal of Institute of Control, Robotics and Systems
• /
• v.2 no.1
• /
• pp.35-44
• /
• 1996

A design method for a teleoperator robot system is presented in this paper. The control system consists of two phases; approach phase and contact one. The end-effector position of the estimated slave robot and the contact force between the end-effector and wall are displayed on the monitors at control site, using which the operator controls the teleoperator system. The approach phase controller is designed using Smith's principle and the contact one designed based upon the structured singular value ${\mu}$ in order to increase the robustness of the system. The uncertainatices such as communication time delay and the variations of system parameters are considered as a muliplicative pertubation. Computer simulations are conducted in order to evaluate the performance of the proposed design method. It is found that desirable control performance, especially in the contact phase, is obtained if the control mode is switched into contact phase when the estimated position of the slave robot end-effector is in front of the wall.

• Food Science and Biotechnology
• /
• v.16 no.2
• /
• pp.183-186
• /
• 2007

The type of mixed gel network of $\kappa$-carrageenan/agar was determined by applying rheological principles. Apparent Young's modulus of the mixed gels was mathematically analyzed with (a) simply adding the moduli of two component gels, (b) phase-separated type's upper and lower bound models, (c) interpenetrating type's logarithmic model. The experimental data fitted the estimates from the operation (a). Whereas, as for the models (b), the experimental values in the agar-rich region fitted the estimates of the upper bound model, but in the $\kappa$-carrageenan-rich region slightly deviated from those of the lower bound model. It reflected an evidence of a phase-separated type, although it was not typical, that there must be data good-fit in the agar-rich and $\kappa$-carrageenan-rich regions with the upper and lower bound models, respectively. Experimental values disagreed with estimates of the model (c). Gel time was analyzed to evince the phase-separated type. As agar concentrations increased at a fixed amount of $\kappa$-carrageenan, gel time gradually decreased and then sharply increased and decreased again. The pattern of such change in gel time also represented a typical behavior of phase-separated type's mixed gels.

• Journal of the Korean Society for Heat Treatment
• /
• v.24 no.1
• /
• pp.23-30
• /
• 2011

This study was carried out to investigate the effect of aging treatment on the mechanical properties and damping capacity of 12Cr heat resistant steel with ferrite phase. While hardness values in ferrite phase was not changed, that in martensite phase was dramatically dropped in early stage of aging treatment and then gradually decreased with increase of aging time. As aging treatment was carried out, the precipitation was not detected in ferrite phase, while carbides were precipitated in martensite phase. With increasing the aging time, tensile strength eventually decreased while impact toughness increased rapidly in the early stage of aging and then gradually increased. Besides, it was confirmed that damping capacity was not changed in the early stage of aging and then gradually increased with increase of aging time.

• Korean Journal of Applied Biomechanics
• /
• v.23 no.1
• /
• pp.19-24
• /
• 2013

The aim of the study was a quantitative analysis of elite athlete's $540^{\circ}$ Dwihuryeochagi and effects of ground movements to the jumping height and kicking velocity. Eleven elite players(Taekwondo demonstration team) participated in this study. In order to get the kinetic and kinematic variables, ten Vicon cameras and a force plate were used. Foot segment velocity(FSV), vertical ground reaction force(GRF), impulse, ground time(GT) in phase 1, trunk angular velocity(TAV), vertical center of gravity(COG), flight time(FT) in phase 2 and kicking leg segment velocity(KSV) in phase 3 were measured and analyzed. Results indicated that there were similar patterns of variables among phases between subjects. Non-significant correlation(r=.145) between flight time(FT) and impulse was found. Also non-significant correlation(r=.119) between center of gravity(COG) and impulse was found. In conclusions, there were similar strategies in phase 1, phase 2, and phase 3 between subjects.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.3
• /
• pp.866-872
• /
• 2014

The purpose of this paper was to find an effective method for measuring electromagnetic torque produced by a brushless DC motor with single-phase current sensing in real-time. A torque equation is derived from the theory of brushless DC motor. This equation is then validated experimentally with a motor dynamometer. A computer algorithm is also proposed to implement the electromagnetic torque estimation equation in real-time. Electromagnetic torque is a linear function of phase current. Estimating the electromagnetic torque in real-time using single-phase current is not appropriate with existing equations, however, because of the rectangular alternating-pulse nature of the excitation current. With some mathematical manipulation to the existing equations, the equation derived in this paper overcame this limitation. The equation developed is simple and so it is computationally efficient, and it takes only motor torque constant and single-phase current to evaluate the electromagnetic torque; no other parameters such as winding resistances, inductances are needed. The equation derived is limited to the three-phase brushless DC motor. It can, however, easily be extended to the multiphase brushless DC motor with the technique described in this paper.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.221-223
• /
• 1999

In this work, samples were manufactured variously by changing conventional calcining and sintering conditions and we tried the utilization by making the heat treatment time, which is demanded to high-Tc phase formation, much shorter. We found out optimal heat treatment conditions with the analysis on formation process at superconducting phase in term of the change of calcining and sintering time and then, examined X-ray diffraction(XRD) patterns, scanning electron microscope(SEM) measurement and energy dispersive X-ray spectrometer(EDX) of the samples manufactured under heat treatment conditions which we suggest here. As a result, 2223 high-$T_c$, phase of (Bi,Pb)SrCaCuO superconductor starting with ($Bi_l$ xPbx,)$_2$$Sr_2$$Ca_2$$Cu_3$$O_y$, composition was formed from 1 hr sintering sample at temperature nearby melting point and also the completed sample with calcining and sintering time of 9 hr was formed high-$T_c$.low-$T_c$ phase appearing in sight above the critical temperature of liquid $N_2$.