• Restorative Dentistry and Endodontics
• /
• v.25 no.1
• /
• pp.17-40
• /
• 2000

Resin cements are used for cementing indirect esthetic restorations such as resin or porcelain inlays. Because of its limitations in curing of purely light cured resin cements due to attenuation of the curing light by intervening materials, dual cured resin cements are recommended for cementing restorations. The physical properties of resin cements are greatly influenced by the extent to which a resin cures and the degree of cure is an important factor in the success of the inlay. The purpose of this study was to evaluate the influence of porcelain thickness and exposure time on the polymerization of resin cements by measuring the microhardness and the degree of conversion, to investigate the nature of the correlation between two methods mentioned above, and to determine the exposure time needed to harden resin cements through various thickness of porcelain. The degree of resin cure was evaluated by the measurements of microhardness [Vickers Hardness Number(VHN)] and degree of conversion(DC), as determined by Fourier Transform Infrared Spectroscopy(FTIR) on one light cured composite resin [Z-100(Z)] and three dual cured resin cements [Duo cement(D), 3M Resin cement(R), and Dual cement(DA)] which were cured under porcelain discs thickness of 0mm, 1mm, 2mm, 3mm with light exposure time of 40sec, 80sec, 120sec, and regression analysis was performed to determine the correlation between VHN and DC. In addition, to determine the exposure time needed to harden resin cements under various thickness of porcelain discs, the changes of the intensity of light attenuated by 1mm, 2mm, and 3mm thickness of porcelain discs were measured using the curing radiometer. The results were obtained as follows ; 1. The values of microhardness and the degree of conversion of resin cements without intervening porcelain discs were 31~109VHN and 51~63%, respectively. In the microhardness Z was the highest, followed by R, D, DA. In the degree of conversion, D and DA was significantly greater than Z and R(p<0.05). 2. The microhardness and the degree of conversion of the resin cements decreased with increasing thickness of porcelain discs, and increased with increasing exposure time, D and R showed great variation with inlay thickness and exposure time, whereas, DA showed a little variation. 3. The intensity of light through 1mm, 2mm, and 3mm porcelain inlays decreased by 0.43, 0.25, and 0.14 times compared to direct illumination, and the respective needed exposure times are 53 sec, 70 sec, and 93 sec. In D and R, 40 sec of light irradiation through 2mm porcelain disc and 80 sec of light irradiation through 3mm porcelain disc were not enough to complete curing. 4. The microhardness and the degree of conversion of the resin cements showed a positive correlationship(R=0.791~0.965) in the order of R, D, Z, DA. As the thickness of porcelain discs increased, the decreasing pattern of microhardness was different from that of the degree of conversion, however.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.860-863
• /
• 2002

Realizations of multirate converters are proposed using periodically time-varying (PTV) structures. By exploiting the computational redundancy of the filtering operation in a multirate filter, it is possible to implement the filter with much less hardware. In the proposed implementations, several coefficients time-share in a periodic fashion the hardware of one multiply-and-add. Therefore, each multiply-and-add circuit performs different coefficient scalings at different time instants within a period. Compared to the direct form realization, the proposed realizations reduce the hardware of an interpolator and a decimator by a factor of approximately U and M, respectively, while retaining the same processing speed, where U and M are the upsampling and downsampling factors, respectively. The approach can be used to obtain realizations for sampling rate conversion by a rational factor of U/M, where U and M are relatively prime, in which case hardware reduction by a factor of approximately UM can be achieved.

• Journal of Plant Biotechnology
• /
• v.50
• /
• pp.267-274
• /
• 2023

All studies on date palm somatic embryogenesis have focused on germination in the presence of light while neglecting germination in darkness, which mimics the germination process of zygotic embryos within seeds. To improve the date palm micropropagation protocol, we investigated the effects of light and darkness incubation on the germination of indirect date palm somatic embryos and their subsequent conversion into plantlets. Darkness incubation emerged as a pivotal factor in the germination of indirect date palm somatic embryos and their successful conversion into plantlets. Darkness incubation significantly decreased the time required for the conversion of indirect somatic embryos into plantlets, halving the duration from 24 weeks to only 12 weeks. The micropropagation protocol was modified, consolidating the previous two distinct stages of germination and elongation under light incubation into a single stage under darkness incubation. These findings modified the protocol and significantly reduced the overall duration of the date palm micropropagation protocol.

• Journal of Mechanical Science and Technology
• /
• v.17 no.2
• /
• pp.197-206
• /
• 2003

It is intended to retrieve the time history of displacement from measured acceleration signal. In this study, the word retrieving means reconstructing the time history of original displacement signal from already measured acceleration signal not just extracting various information using relevant signal processing techniques. Unlike extracting required information from the signal, there are not many options to apply to retrieve the time history of displacement signal, once the acceleration signal is measured and recorded with given sampling rate. There are two methods, in general, to convert measured acceleration signal into displacement signal. One is directly integrating the acceleration signal in time domain. The other is dividing the Fourier transformed acceleration signal by the scale factor of - $\omega$$^2$and taking the inverse Fourier transform of it. It turned out both the methods produced a significant amount of errors depending on the sampling resolution in time and frequency domain when digitizing the acceleration signals. A simple and effective way to convert the time history of acceleration signal into the time history of displacement signal without significant errors is studied here with the analysis on the errors involved in the conversion process.

• Korean Chemical Engineering Research
• /
• v.52 no.1
• /
• pp.133-140
• /
• 2014

The experiment was designed to compare the char combustion kinetics of pulverized Indonesia coals commonly utilized in Korea power plants. The reaction rate of coal char has been formulated using the external and internal effectiveness factors to describe the diffusion effect quantitatively. The Random Pore Model (RPM) was used for applying internal specific surface area as a function of carbon conversion ratio. Reaction rate was obtained from reaction time using the Wire Heating Reactor (WHR) which can heat and measure the char particle temperature at the same time. BET and TGA were used to obtain physical properties such as internal specific surface area and structural parameter. Three kinds of Indonesia Sub-bituminous coals "BARAMULTI, ENERGYMAN, AGM" were used in order to derive the activation energy and pre-exponential factor. The results of this study showed that the effect of internal diffusion than that of external diffusion is the dominant as comparison of kinetics was reflected in external and internal effectiveness factors. For three kinds of coal char, finally, activation energy of intrinsic kinetics indicates 110~118 kJ/mol.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.18 no.3
• /
• pp.262-267
• /
• 2006

For the concentration management in COD parameters, it requires the measurement and estimation of the COD pollutants load (hereinafter PL) in the watershed. The estimation method of the PL, however, is provided only based on the BOD parameters. The development of COD PL estimation schemes is expected to execute total PL management in coastal zone and needs to more observation and much time. This study provides COD PL estimation schemes using statistical information about ratio analysis with COD & BOD concentration of rivers and drainages of an industrial complex in Lake Shiwha and Incheon Coastal Zone watershed. The COD PL is computed with ease by multiplying the conversion factor, which is calculated as the sum of the average and 1 to 3 (safety factors) times standard deviation. The conversion factor of Lake Shihwa and Incheon Coastal Zone is estimated as 1.7, 2.3 and 2.9 with respect to the safety factor 1, 2, and 3, respectively.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.403-407
• /
• 2011

본 연구에서는 임의시간 환산계수(Conversion Factor, CF)와 관련하여 거의 유일한 이론적 연구인 Weiss 모형을 자세히 검토하고, 그 문제점을 보완한 수정 Weiss 모형을 제안하였다. 특히, 임의시간 환산계수를 이론적인 방법을 통해 산정하는 과정에서 강우 지속기간과 강우 시간분포의 특성을 반영하지 못하는 한계를 극복하는 시도의 하나로서 강우의 시간분포 특성을 고려하여 CF를 결정하였다. 이를 실제 관측 자료에 근거한 국내 외 CF값들과 비교해본 결과, 수정 Weiss 모형을 근거로 산정한 CF값은 강우 시간분포의 특성에 영향을 받으며 그 형태에 따라 다양한 값이 나타남을 확인할 수 있었다.

• Journal of Applied Reliability
• /
• v.6 no.2
• /
• pp.115-134
• /
• 2006

This paper deals with OO aircraft mission reliability prediction. To demonstrate user-required mission reliability, it is calculated with use general formulae which are used in reliability engineering. The mission reliability of OO aircraft is calculated in considering conversion factor (CF) on the each subsystems' MTBF. The prediction results are explained only the state at present time. Because these data are not real data in operational environments. Therefore, in the case of OO aircraft, it has to be needed collecting the real and renewal data which are operational and empirical. After that, continuing the data upgrading, it is easily closed to the more exact reliability value.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.29 no.2
• /
• pp.167-175
• /
• 2019

Objectives: The purpose of this study was to evaluate airborne radon and thoron levels and estimate the effective doses of workers who made household goods and mattresses using monazite. Methods: Airborne radon and thoron concentrations were measured using continuous monitors (Rad7, Durridge Company Inc., USA). Radon and thoron concentrations in the air were converted to radon doses using the dose conversion factor recommended by the Nuclear Safety and Security Commission in Korea. External exposure to gamma rays was measured at the chest height of a worker from the source using real-time radiation instruments, a survey meter (RadiagemTM 2000, Canberra Industries, Inc., USA), and an ion chamber (OD-01 Hx, STEP Co., Germany). Results: When using monazite, the average concentration range of radon was $13.1-97.8Bq/m^3$ and thoron was $210.1-841.4Bq/m^3$. When monazite was not used, the average concentration range of radon was $2.6-10.8Bq/m^3$ and the maximum was $1.7-66.2Bq/m^3$. Since monazite has a higher content of thorium than uranium, the effects of thoron should be considered. The effective doses of radon and thoron as calculated by the dose conversion factor based on ICRP 115 were 0.26 mSv/yr and 0.76 mSv/yr, respectively, at their maximum values. The external radiation dose rate was $6.7{\mu}Sv/hr$ at chest height and the effective dose was 4.3 mSv/yr at the maximum. Conclusions: Regardless of the use of monazite, the total annual effective doses due to internal and external exposure were 0.03-4.42 mSv/yr. Exposures to levels higher than this value are indicated if dose conversion factors based on the recently published ICRP 137 are applied.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.05a
• /
• pp.809-811
• /
• 2010

In most floating-point operations related with 3D graphic applications for mobile devices, properly approximated data calculations with reduced complexity and low power are preferable to exactly rounded floating-point operations with unnecessary preciseness with cost. Among all the sophisticated floating-point arithmetic operations, multiplication and division are the most complicated and time-consuming, and they can be transformed into addition and subtraction repectively by adopting the logarithmic conversion. In this process, the most important factor for performance is how high we can make an approximation of the logarithm conversion. In this paper, we cover the trends in studying the logarithm conversion circuit designs. We also discuss the important factor in design issues and the applicable fields in detail.