• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.12
• /
• pp.209-216
• /
• 2000

The lateral behavior of the moving web is critical to the quality of the web products. The alignment of the rollers carrying the web is found to be one of important factors to the lateral behavior of the moving web. But, the study on the effect of the tilting roller in the direction of the normal to the moving web on the lateral behavior has not been reported in the literature yet. For example, the contact roller often contacts the winding roll in a tilted fashion and causes the lateral motion of the winding web, which induces the offset on the wound roll. The lateral dynamics of the moving web induced by a tilted roller in normal direction of a web is investigated in this paper. The two-dimensional dynamic model developed by Shelton is extended to investigate the effect of a titled roller in a normal direction of the moving web on the lateral motion of the moving web. New boundary conditions are developed to solve the extended model. Computer simulation study proved that the model developed can be used to predict the lateral motion of the moving web ？ to a tilted roller in normal direction of the moving web. The lateral deflection is increased exponentially a the tilting angle is increased. As the length of web span is increased, the amount of lateral deflection was increased almost linearly for the same tilting angle. The lateral dynamics turned out to be almost independent to the operating tension. The model developed can be used to solve the offset problem of the staggered winding and also to design a new web guiding mechanism.

• Tribology and Lubricants
• /
• v.31 no.4
• /
• pp.177-182
• /
• 2015

Tapered roller bearings are widely used in equipment where high combined thrust and radial loads are experienced. A certain amount of tilting between the tapered rollers and the races always occurs because of bending moment load conditions and shaft deflection. It is now well understood that a coherent elastohydrodynamic lubrication (EHL) film separates the rollers and races. In spite of extensive study on EHL problems for over half a century, relatively few studies have focused on the finite line contacts problem. This study presents a complete numerical analysis of the effects of roller tilting on the EHL characteristics in a tapered roller bearing. We systematically analyze this highly nonlinear problem using finite differences with fully non-uniform grids and the Newton-Raphson method. Detailed EHL pressure distributions and film shapes are presented under moderate loads and material parameters. A very small roller tilting significantly affects the pressure distributions and film shapes near both ends of the roller. Moreover, the effect of tilting on the EHL characteristics at the small end is much greater than that at the large end. Therefore, in designing optimum profiles for tapered roller bearings, the profile radius should be larger at the small end.

• Tribology and Lubricants
• /
• v.26 no.5
• /
• pp.263-271
• /
• 2010

The rollers of cylindrical roller bearing are axially profiled to relieve high edge stress concentration caused by mainly their finite length and by misalignment. In this paper, a numerical analysis is carried to study the EHL of misaligned (tilted) rollers with axially profiled ends. Using a finite difference method with non-uniform grids and the Newton-Raphson method, the highly nonlinear EHL problems are systematically solved. Physically consistent solutions are obtained for moderate load, material parameters and very small misalignment. For different misalignment angles, contours and sectional plots of pressure and film shape near both edge regions are compared. The asymmetric pressure distributions and film shapes show that the EHL results of finite line contacts are highly dependent upon very small amounts of roller misalignment. Especially, the effect of misalignment on the EHL pressure distribution is much higher than the film shapes.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.5
• /
• pp.84-89
• /
• 2001

The alignment of the rollers carrying the web is found to be one of important factors to the lateral behavior of the moving web and to the quality of the final web products. But, the perfect alignment of the rollers is not always possible and the web itself can be cambered. Thus the control of lateral behavior of the moving web is critical in the most of web handling systems. The web guiding system that adjusts the angle of the alignment between two adjacent rollers is commonly used in industry. But, in this paper a new web guiding system is proposed by using the lateral dynamics of the moving web induced by a tilted roller in normal direction of a web. The computer simulation study was carried out to verify the steering performance of the suggested guiding system. Computer simulation study shows that the performance of the new guiding mechanism is better than that of an existing guiding mechanism.