• 대한기계학회논문집
• /
• 제19권3호
• /
• pp.705-712
• /
• 1995

The wear characteristics and wear mechanisms in TiN coating deposited on high speed steel and alloy tool steel by ion plating were investigated. Pin on V-block wear tester was used for a wear test method. The specimen was composed of three kinds of high speed steel and alloy tool steel which had different hardness by changing the heat treating condition. Three kinds of coating thickness were also applied to each specimen. Microscopic observation of worn surfaces was made by SEM. The scratch test of coating surface by the ion plating showed that critical load to break the coating interface was greater than 50N. The critical load increased with both substrate hardness and coating thickness. The wear resistance of TiN coated high speed steel became 10 times greater than that of non-coated ones. SEM observation showed that leading edge of contact was compressive and trailing edge was under maximum tensile stress and then surface cracking broke out perpendicular to sliding direction.

• 한국표면공학회지
• /
• 제28권2호
• /
• pp.77-82
• /
• 1995

In this study, we examined the relationships between the coating film's properties, such as microhardness, adhesion of coating fil $m_strate, and machining tool's life time. Samples were prepared by coating TiN on the 5.5 diameter twist drills using reactive ion plating technology, For measuring microhardness and adhesion of fil $m_strate, HSS plate was used for substrate. TiN coated drill's life time was dependent on the adhesion of fil $m_strate and averagely increased by several ten times more than uncoated drill's. The major parameter affecting TiN coated drill's life time was the strong adhesion between coating film and substrate.ate.

• 한국공작기계학회논문집
• /
• 제15권1호
• /
• pp.49-55
• /
• 2006

The effect of coating temperature with regard to surface properties of TiN-coated layer on hard metal(WC-Co) are experimentally investigated. Hardness, surface roughness, TiN coating thickness and adsorption force were measured in order to evaluate the effect of coating temperature. The two-way ANOVA method is used in order to evaluate the experimental data. In AIP processing, It is concluded that the furnace temperature in the range of $400^{\circ}C\~500^{\circ}C$ affected to a little increasing the number of production with the coating temperature.

• 한국표면공학회지
• /
• 제30권5호
• /
• pp.298-309
• /
• 1997

Hard Tin coating on tool steel substrate were prepared using the pulsed PACVE. An orthogonal experimental design was employed to find the best deposition conditions for TiN coating and to systematically understand the effect of processing parameters. The small size Taguchi matrix called the L16 was used for experiment and ANOVA(ANalysis of VAriance) was followed to study the effect of main parameters on hardness and adhesion TiN coatings. In conclusion, pulse on/off time ratio and pulsing frequency were the major deposition parameters to determine hardness and adhesion of TiN coating in the pulsed DC PACVE process. (200) preferred orientation, columnar growth and dome-shaped surface morphology of the TiN films gave rise to a high hardness and a good adhesion to the substrates.

• 열처리공학회지
• /
• 제5권1호
• /
• pp.1-12
• /
• 1992

In order to improve adhesive force of TiN film, we sputtered titanium as interlayer before TiN deposition by Plasma Enhanced Chemical Vapour Deposition. We observed changes of hardness and adhesion at a various thickness of titanium interlayer and also examined analysis. At the critical thickness of the titanium interlayer(about $0.2{\mu}$), adhesive force of TiN films were promoted mostly. But over the critical thickness, a marked reduction of adhesive force was showed, because of the internal stress of titanium interlayer. From AES analysis, the adhesion improvement of TiN films was mainly caused by nitrogen diffusion into titanium interlayer during TiN deposition process which relieved stress concentration at TiN coating-substrate interface.

• Corrosion Science and Technology
• /
• 제10권6호
• /
• pp.212-217
• /
• 2011

In this study, corrosion characteristics of TiN and ZrN film on the abutment screw by arc-ion plating were investigated using a potentiodynamic anodic polarization test in deaerated 0.9% NaCl solution at $36.5{\pm}1^{\circ}C$. The surface morphologies of the coating layers before and after corrosion test were investigated by a field-emission scanning electron microscope (FE-SEM) and a energy dispersive x-ray spectroscopy (EDS). The surfaces of the TiN and ZrN coated abutment screws showed the smooth surfaces without mechanical defects like scratches which can be formed during the manufacturing process, compared with those of the non-coated abutment screw. The corrosion and passive current densities of TiN and ZrN coated abutment screws were lower than those of the non-coated abutment screw.

• 한국표면공학회지
• /
• 제34권2호
• /
• pp.97-104
• /
• 2001

($Ti_{ 1-x}$$Al_{ x}$)N has been deposited on high speed steel (HSS) substrate using PECVD from the gas mixture of $TiC1_4$, $AlC1_4$, $NH_3$, $H_2$, and Ar. The correlation between the microstructure and the mechanical properties was investigated. ($Ti_{1-x}$$Al_{ x}$)N showed single phase NaCl-structure up to X=0.87, while a mixed phase of NaCl Type (Ti, Al) N and wurtzite structure AlN was observed for 0.87$Ti_{1-x}$ $Al_{x}$ )N became by degrees as increasing X, which made the hardness of the coating higher by Al addition. When the coating was composed of a mixed phase, however, the hardness decreased abruptly due to the effect of soft AlN phase. The wear volume of the coatings could be obtained as the concentration of the coating was varied, and the relation between the wear volume and hardness or the adhesion strength was discussed.

• 대한금속재료학회지
• /
• 제46권10호
• /
• pp.691-699
• /
• 2008

Electrochemical characteristics of Ti-30Ta-xZr alloys coated with HA/TiN by using magnetron sputtering method were studied. The Ti-30Ta containing Zr(3, 7, 10 and 15wt%) were 10 times melted to improve chemical homogeneity by using a vacuum furnace and then homogenized for 24hrs at $1000^{\circ}C$. The specimens were cut and polished for corrosion test and coating, and then coated with HA/TiN, respectively, by using DC and RF-magnetron sputtering method. The analyses of coated surface and coated layer were carried out by using optical microscope(OM), field emission scanning electron microscope(FE-SEM) and X-ray diffractometer(XRD). The electrochemical characteristics were examined using potentiodynamic (-1,500 mV~ + 2,000 mV) and A.C. impedance spectroscopy(100 kHz ~ 10 mHz) in 0.9% NaCl solution at $36.5{\pm}1^{\circ}C$. The microstructure of homogenized Ti-30Ta-xZr alloys showed needle-like structure. In case of homogenized Ti-30Ta-xZr alloys, a-peak was increased with increasing Zr content. The thickness of TiN and HA coated layer showed 400 nm and 100 nm, respectively. The corrosion resistance of HA/TiN-coated Ti-30Ta-xZr alloys were higher than that of the non-coated Ti-30TaxZr alloys, whic hindicate better protective effect. The polarization resistance($R_p$) value of HA/TiN coated Ti-30Ta-xZr alloys showed $8.40{\times}10^5{\Omega}cm^2$ which was higher than that of non-coated Ti-30Ta-xZr alloys.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2000년도 춘계학술발표회 초록집
• /
• pp.32-33
• /
• 2000

• 소성∙가공
• /
• 제31권1호
• /
• pp.11-16
• /
• 2022

In this paper, wear characteristics of PVD coatings were compared on the die surface for cold stamping of MART1470 steel sheet with the finite element analysis and the pin-on-disc wear test. Three types of PVD coatings (CrN, TiAlCrN, and MoS2TiCr(W)N) were considered for the tool surface made of STD11 material. The stamping process of an auto-body part was analyzed with the finite element method. Ranges of process variables for the wear test such as contact pressure, relative speed, and sliding distance were predicted from analysis results. In order to quantitatively analyze wear characteristics of each coating, the amount of wear was measured and compared according to process variables with the pin-on-disc wear test. The influence of each process variable was investigated and the wear characteristics of the three coating layers were quantitatively compared. It was confirmed that the wear characteristics of MoS₂TiCr(W)N coating were better than those of CrN and TiAlCrN. It was noted that the proposed prediction approach could predict and respond to the wear phenomenon occurring in the stamping process.