• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2007.11a
• /
• pp.120-122
• /
• 2007

3성분계 $Ti-C_x-N_{1-x}$ 코팅막은 AIP(Arc Ion Plating)법에 의해 -25V의 바이어스와 $300^{\circ}C$의 분위기에서 스테인리스 스틸 기판 위에 증착시켰다. $Ti-C_x-N_{1-x}$ 코팅막 안의 탄소(carbon)는 유입가스 비 $CH_4/(CH_4+N_2)$를 변화시키며 합성하였다. 탄소(carbon)가 증가함으로써, $Ti-C_x-N_{1-x}$ 코팅막의 미세경도는 TiN 코팅막의 20 GPa로부터 x=0.52에서 최대 약 32 GPa로 측정되었다. 또한, 미세구조는 잔류응력과 관련 있으며 탄소 함량에 따라 평균마찰계수가 크게 감소하였다.

• Journal of the Korean Ceramic Society
• /
• v.31 no.6
• /
• pp.637-642
• /
• 1994

Using SHS(Self-propagating High-temperature Synthesis) method, the optimum synthetic condition of titanium carbonitride was established by controlling the parameters such as relative density of mixture (Ti+C), nitrogen pressure, additive amounts of titanium hydride(TiH1.924) and protecting heat loss. Under 1 atm nitrogen pressure, nitridation ratio with changing relative density of the sample compacts has a maximum (87.2%) at about 55%, and in the case of enveloping the pellet with a quartz tube, the highest nitridation ratio of 90% was obtained at about 68%. At relative density of 55%, nitridation ratio with the nitrogen pressure has a miximum (87.3%) at 7 atm. As the amounts of additive titanium hydride increased, nitridation ratio decreased at below 7 atm nitrogen pressure and, increased at above this pressure until percent of addition percent reached 15 wt% and decreased abruptly upon futher increases in titanium hydride. In the synthesis of TiCxNy by combustion reaction, heat transfer from combustion zone to preheating zone and nitrogen gas penetration into the compact were found to be important factors affecting the TiCxNy formation. It was difficult to obtain high nitridation ratio when the conbustion temperature was either too high or too low, and it seems that the retention of high temperature after a combustion wave sweeped through the reactant mixture pellet is critical to obtain a satisfactory nitridation ratio.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1110-1111
• /
• 2006

[ $Ti_3SiC_2$ ] was coated with $Al_2O_3$, MgO and $SiO_2$ respectively by sol-gel method and cured at 900 and $1200^{\circ}C$. The coated oxides did not react with $Ti_3SiC_2$ at $900^{\circ}C$ but reacted with it to form $TiC_x$ at $1200^{\circ}C$. The specimen coated with $SiO_2$ at $900^{\circ}C$ formed a dense protecting layer and showed the best oxidation resistance at $800^{\circ}C$ in air. However, the dense protecting layers did not form in $Al_2O_3$ and MgO coated specimens cured even at $900^{\circ}C$. MgO coated specimen showed the worst improvement in the oxidation resistance because the reactivity of MgO with $Ti_3SiC_2$ was highest. On the other hand, the electrical conductivities were measured in MgO and $Al_2O_3$ coated specimens to have TiCx but could not be measured in the $SiO_2$ coated ones because of the nonconductive dense protected layers.

• Journal of Magnetics
• /
• v.3 no.4
• /
• pp.116-119
• /
• 1998

Influence of small additions ($\leq$2.0 at.%) of Al, Ti, Co, and Ni on the microstructural development and the magnetic properties of melt-spun Fe-Bd-C alloys was investigated. Addition of these elements tended to stabilize the crystallization of as-spun ribbons. Especially, Al and Ti preferred to stabilize$ Fe_{17}Nd_2C_x.$ The average grain size of Fe17Nd2Cx (0.1~0.3 ${\mu}{\textrm}{m}$), obtained by a proper annealing, in the ribbon treated with 0.5 at.% additive was much smaller than that of additive-free ribbons, which would be the major source of large increase in coercivity. Among the additives, Ni was very effective to increase the coercivity whereas Co had beneficial effect on $T_c.$ By adding 0.5 at.% Ni, intrinsic coercivities of more than 1.4 T, 40~50% higher than that (~1.0T) of additive-free ribbons, can be obtained after annealing at 750~80$0^{\circ}C$.

• Entomological Research
• /
• v.48 no.5
• /
• pp.439-447
• /
• 2018

Adult mosquito surveillance was conducted from 2013 through 2014 at four cattle sheds, a wild bird refuge, and two residential areas located in Gyeongnam Province in the Republic of Korea. Adult mosquitoes were collected in black light traps from April 1, through November 30. Mosquito surveillance was conducted to figure out population densities of vector mosquitoes, possibly invaded mosquitoes and identify various virus infections at the selected sites. A total of 107,466 females comprising 14 species and 7 genera were collected from 2013 to 2014. The most common species collected were Culex tritaeniorhynchus Giles (63.8%), Anopheles sinensis s.l. (18.9%), Aedes vexans nipponii (Theobald) (7.7%), and Culex pipiens Coquillett (5.1%). Trap indices (TIs) varied widely for species over their range, due to geographical distribution and degree of association with rural and urban communities. The most collected An. sinensiss.l. and Cx. tritaeniorhynchus appeared at a cow shed in Hapcheon (TI 347.5) and a pigsty in Daejeo-1-dong, Busan (TI 1,040.8), respectively, due in part to their situation near breeding sites such as rice paddies. The bi-weekly population densities for mosquito species were variable for each of the years, apparently as a result of variable annual weather conditions. None of the mosquito species collected tested for the flavivirus including Japanese Encephalitis Virus, West Nile Virus, Dengue Virus, and Zika Virus infections by polymerase chain reaction (PCR) assay were positive.

• Journal of Integrative Natural Science
• /
• v.2 no.1
• /
• pp.18-23
• /
• 2009

This minireview provides the chosen examples of our recent discoveries in the polymerization of hydrosilanes, dihydrosilole, lactones, and vinyl derivatives using various catalysts. Hydrosilanes and lactones copolymerize to give poly(lactone-co-silane)s with $Cp_2MCl_2$/Red-Al (M = Ti, Zr, Hf) catalyst. Hydrosilanes (including dihydrosilole) reduce noble metal complexes (e.g., $AgNO_3$, $Ag_2SO_4$, $HAuCl_4$, $H_2PtCl_6$) to give nanoparticles along with silicon polymers such as polysilanes, polysilole, polysiloxanes (and silicas) depending on the reaction conditions. Interestingly, phenylsilane dehydrocoupled to polyphenylsilane in the inert nitrogen atmosphere while phenylsilane dehydrocoupled to silica in the ambient air atmosphere. $Cp_2M/CX_4$ (M = Fe, Co, Ni; X = Cl, Br, I) combination initiate the polymerization of vinyl monomers. In the photopolymerization of vinyl monomers using $Cp_2M/CCl_4$ (M = Fe, Co, Ni), the photopolymerization of MMA initiated by $Cp_2M/CCl_4$ (M = Fe, Co, Ni) shows while the polymerization yield decreases in the order $Cp_2Fe$ > $Cp_2Ni$ > $Cp_2Co$, the molecular weight decreases in the order $Cp_2Co$ > $Cp_2Ni$ > $Cp_2Fe$. For the photohomopolymerization and photocopolymerization of MA and AA, the similar trends were observed. The photopolymerizations are not living. Many exciting possibilities remain to be examined and some of them are demonstrated in the body of the minireview.