• Proceedings of the KIEE Conference
• /
• 2007.11c
• /
• pp.138-140
• /
• 2007

$TiO_2-V_2O_5$ sol was fabricated using sol-gel method and $TiO_2-V_2O_5$ thin films were fabricated using dip-coating method. $V_2O_5$ sol was added 0.01mo1e, 0.03mo1e, 0.05mo1e into $TiO_2$ sol. Viscosity of sol increased fast from about 1,000 minutes and sol began gelation from about 10,000 minutes. As a results of crystalline properties, $V_2O_5$ peaks were not found despite of $V_2O_5$ addition. Endothermic reaction occurred due to evaporation of solvent and dissociation of OH at $80^{\circ}C$. Exothermic reaction occurred due to combustion and oxidation of solvent at $230^{\circ}C$, occurred to combustion and oxidation of alkyl group at $350^{\circ}C$. Thickness of thin films increased $0.1{\sim}0.25{\mu}m$ every a dipping.

• Korean Journal of Metals and Materials
• /
• v.49 no.2
• /
• pp.121-127
• /
• 2011

The mechanical properties of the various heat treatment conditions on Ti-15Mo-3Nb-3Al-0.2Si alloy plates were examined. XRD patterns from the surface of Ti-15Mo-3Nb-3Al-0.2Si were analyzed as a solution-treated Ti alloy has the single-phase ${\beta}$ structure whereas the aged Ti alloys have the ${\beta}$ matrix embedded with ${\alpha}$ needles. High strength (~1500 MPa) with decent ductility (7%) was obtained by the Ti alloy double aged at $300^{\circ}C$ and $520^{\circ}C$ for 8 hours each. The double-aged alloy exhibits the finer structure than the single-aged alloy at $300^{\circ}C$ for 8 hours because of the higher nucleation rate of ${\alpha}$ needles at an initial low aging temperature ($320^{\circ}C$). TEM observation revealed that the fine nanostructure with ${\alpha}$ needles in the ${\beta}$ matrix ensured the excellent mechanical properties in the double aged Ti-15Mo-3Nb-3Al-0.2Si alloy. In the solution treated alloy, the yield drop, stress-serrations and the ductility minimum typically associated with dynamic strain aging can be attributed to the dynamic interaction between dislocations and oxygen atoms. The yield drop and the stress serration were not observed in aged samples because the geometrically introduced dislocations due to phase precipitates suppressed the dynamic strain aging.

• Korean Journal of Materials Research
• /
• v.24 no.4
• /
• pp.201-206
• /
• 2014

TiC-21 mol% Mo solid solution (${\delta}$-phase) and TiC-99 mol% Mo solid solution (${\beta}$-phase), and TiC-(80~90) mol% Mo hypo-eutectic composite were deformed by compression in a temperature range from room to 2300 K and in a strain rate range from $4.9{\times}10^{-5}$ to $6.9{\times}10^{-3}/s$. The deformation behaviors of the composites were analyzed from the strengths of the ${\delta}$- and ${\beta}$-phases. It was found that the high strength of the eutectic composite is due primarily to solution hardening of TiC by Mo, and that the ${\delta}$-phase undergoes an appreciable plastic deformation at and above 1420 K even at 0.2% plastic strain of the composite. The yield strength of the three kinds of phase up to 1420 K is quantitatively explained by the rule of mixture, where internal stresses introduced by plastic deformation are taken into account. Above 1420 K, however, the calculated yield strength was considerably larger than the measured strength. The yield stress of ${\beta}$-phase was much larger than that of pure TiC. A good linear relationship was held between the yield stress and the plastic strain rate in a double-logarithmic plot. The deformation behavior in ${\delta}$-phase was different among the three temperature ranges tested, i.e., low, intermediate and high. At an intermediate temperature, no yield drop occurred, and from the beginning the work hardening level was high. At the tested temperature, a good linear relationship was held in the double logarithmic plot of the yield stress against the plastic strain rate. The strain rate dependence of the yield stress was very weak up to 1273 K in the hypo-eutectic composite, but it became stronger as the temperature rose.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 1999.10a
• /
• pp.3-4
• /
• 1999

최근 산업이 고속도화, 고능률화 및 고정멸화의 추세로 발전함에 따라 우수한 내마모성, 인성, 고온 안정성 및 내구성을 갖는 공구 및 금형을 요구하게 되었다. 그러나 이와같은 성질들은 어떤 단일 재료에서는 얻을 수 없으며 적당한 기판공구나 금혈위에 내마모성 보호피막을 coating함으로 비교적 저렴하게 얻을 수 있다. 화학증착법으로 TiC, TiN등을 증착시킬때에는 $1000^{\circ}C$정도의 반응온도가 필요하며 이러한 증착온도는 모재가 초경합금일때는 문제가 안되나 강재일 경우 모재의 연화와 칫수변화의 문제를 야기시킨다. 최근에는 플라즈마를 사용하여 증착반응온도를 $550^{\circ}C$ 이하로 낮추는 플라즈마 화학 증착볍(PACVD)이 대두되고 있다. 그러나 이 방법어서 는 뚱착하려는 금속원소가 TiCl4의 형태로 공급되고 있으므로 생성된 층이 염소를 포함하고 있다. 이 층에 잔존하는 염소는 층의 기계적 성질을 저하시키고 층내의 stress를 유발시킨다. 또한 HCI개스의 생성으로 인하여 펌프 및 장비의 부식이 촉진 된다 이러한 결점을 극복하기 위하여 금속유기화합물 전구체(metallo-organic precursor)로 $TiCl_4$를 대체하고자 하는 연구가 활발하게 진행되고 있으며 본 연구실에서 이에 대하여 연구한 결과를 소개하고자 한다. diethylamino titanium을 전구체로 사용하여 $H_2,\;N_2,\;Ar$분위기하에서 pulsed d.c.를 사용하는 MO-PACVD에 의하여 $150~250^{\circ}C$의 저온에서 Al 2024 기판에 TiCN층 형 성을 하였다. 전구체 증발온도는 $74~78^{\circ}C$의 온도범위어야 하며 고경도의 코탱층은 54% duty, 14.2kHz, 450V의 조건에서 얻어졌으며 duty, 주파수, 전압이 증가함에 따라 경도는 저하되었다. 이때의 표면 morphology를 SEM으로 조사한바 dome structure가 크게 발달되었음을 알 수 있었다. 본 실험의 온도 범위내에서 얻은 TiCN 증착반응의 활성화에너지는 7.5Kcal/mol이었다. 증착된 TiCN층은 우수한 내마모섣을 나타내었으며 스크래치테스트 결과 17N의 엄계하중을 나타내었다. 본 연구에서 변화 시킨 duty, 주파수, 전압의 범위에서는 층의 밀착력은 크게 변화하지 않았다. titanium isopropoxide를 전구체로 사용하여 Hz, Nz 분위기하에서 d.c.를 사용하는 MO-PACVD에 의하여 Ti(NCO) 코팅층을 SKDll, SKD61, SKH9 공구강에 형성시키는 공정을 개발하였다. 최적의 Ti(NCO) 코탱층을 얻기 위해 유입전구체 부피%의 양은 향착압력의 5%를 넘지 않아야 되고 수소와 젤소 가스비가 1:1일 때 가장 높은 코팅층의 경도값을 나타내었다. 수소와 질소 가스비가 3:7일 때 TiFeCr(NCO)의 복화합물 코팅층이 형성됨을 알 수 있었고 500t의 증착온도에서 얻은 Ti(NCO) 코팅층이 높은 경도값과 좋은 내식성을 나타내었다. 또한 이와같은 Ti(NCO) 코팅공정과 본 실험실에서 개발한 확산층만 형성시키는 plsma nitriding 공정을 결합하여 복합코탱층을 형성하였는데 이 복합코팅층은 고경도와 우수한 내마모성, 내식성 뿐만 아니라 10)N 이상의 뛰어난 밀착력을 나타내었다. 현재 많이 사용되고 있는 PVD법은 step coverage가 좋지 않은 점과 cost intensive p process라는 단점이 있다. MO-PACVD법은 이러한 문제를 해결할 수 있는 방법으로서 앞으로 지속적인 도전이 요구되는 분야이다.

• Journal of Korea Foundry Society
• /
• v.27 no.3
• /
• pp.120-125
• /
• 2007

The microstructure, mechanical properties and melting range of Ni-Cr-Mo based alloys were investigated to develop Be-free Ni-Cr-Mo base dental alloys for Porcelain-Fused-to-Metal Firing(PFM). All as-cast alloys showed dendritic structure. Rockwell hardness of 20Cr7Mo was increased with addition of Si and Ti. On the contrary, it was decreased with addition of Co. The duplex alloying elemental addition such as 3Co + xTi, 2Si + xCo and 2Si + xTi to 20Cr7Mo resulted in much increase of hardness. Rockwell hardness and compressive strength for 20Cr3CoSiTi or 17Cr6CoSiTi alloy that add Si-Ti had similar values compared to the commercial alloys. Melting range for 20Cr3CoSiTi and 17Cr6CoSiTi alloy that add Si-Ti showed similar or lower than commercial alloys. In conclusion, 20Cr3CoSiTi and 17Cr6CoSiTi alloys can be applied for commercial use.

• Journal of the Korean Magnetics Society
• /
• v.2 no.3
• /
• pp.239-243
• /
• 1992

It has been found that B is very effective for the increase of magnetization and Curie temperature in $NdFe_{11}TiN_x$-type compounds having $ThMN_{12}$-type structure. Experimental results have shown that magnetization and Curie temperature of $NdFe_{10.7}TiB_{0.3}N_x$ are 148 $Am^2$/kg and $560^{\circ}C,$ respectively, by about 20 $Am^2$/kg and $90^{\circ}C$ higher than those of $NdFe_{10.7}Ti_{1.3}N_x.$ On the other hand, Mo is effective for the increase of anisotropy field, and it seems to strongly inhibit the formation of ${\alpha}-Fe$ phase during the nitrification treatement. The anisotropy field of $NdFe_{10.7}TiMo_{0.3}N_x$ is about 7960 kA/m (100 kOe) which is about 1590 kA/m (20 kOe) higher than that of $NdFe_{10.7}Ti_{1.3}N_x$.

• Journal of the Korean Ceramic Society
• /
• v.28 no.2
• /
• pp.101-108
• /
• 1991

0.2 mo1% La doped BaTiO3 samples were prepared by a wet chemical process (Pechini process) and electrical conductivity were measured from annealing temperatures(800-110$0^{\circ}C$) to room temperature continuously. 2 probe I-V characteristics showed that Pt electrodes were non-ohmic below about 80$0^{\circ}C$ for Ladoped sample. I-V curves showed varistor behavior and breakdown voltages showed PTC-like behavior. AC complex impedance of 0.2 La and 0.05 Mn mo1% doped BaTiO3 samples with three different electrodes (electroless Ni, Pt, Ag electrodes) were measured with temperature variation. Complex impedance plots showed that the samples with electroless Ni electrodes have negligible electrode resistance. Samples with Ag or Pt paste electrodes showed large electrode resistance. PTC effect, which is defined as the ratio of maximum resistance to minimum resistance, was found to be less than 10 for 0.2 mo1% La doped dense sample however greater than 105 with codoping of 0.05 mo1% Mn and 0.2 mol% La.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1996.11a
• /
• pp.23-23
• /
• 1996

• Korean Journal of Metals and Materials
• /
• v.48 no.8
• /
• pp.741-748
• /
• 2010

We studied the corrosion and oxidation properties of Fe-18Cr-0.4Nb-(0.1~0.6)Ti-(1~3)Si-(0.5~2)Mo stainless steel. The resistance to general and pitting corrosion was evaluated and the results were analyzed by Response Surface Methodology (RSM) as a function of alloy composition. The effects of alloy composition and heat treatment on the oxidation resistance were also examined. Mo increased both general corrosion resistance and pitting corrosion resistance. Si improved the resistance of the alloys to pitting corrosion. Si was also beneficial for general corrosion resistance of the alloys containing Mo at more than 1 wt.%. However, Mo was detrimental when its content was lower. Effects of Ti on general corrosion properties appeared to be weak and a high concentration of Ti appeared to deteriorate pitting resistance. The thickness of the oxidation scale increased and adhesion of the scale worsened as the temperature increased from $800^{\circ}C$ to $900^{\circ}C$. Weight gain of the alloys due to oxidation at $900^{\circ}C$ clearly showed that the resistance to oxidation is improved by annealing at $860^{\circ}C$ and an increase of Si content.

• Korean Journal of Metals and Materials
• /
• v.50 no.6
• /
• pp.469-475
• /
• 2012

A high-energy mechanical milling (HEMM) process was introduced to improve sinter-ability, and rapid sintering of spark plasma sintering (SPS) under pressure was used to make ultra fine grain (UFG) of Ti-Nb-Mo-CPP composites, which have bio-attractive elements, for increasing mechanical properties. Ti-Nb-Mo-CPP composites were successfully fabricated by SPS at $1000^{\circ}C$ within 5 minutes under 70 MPa using HEMMed powders. The Vickers hardness of the composites increased with increased milling time and addition of CPP contents. Biocompatibility and corrosion resistance of the Ti-Nb-Mo alloys were improved by addition of CPP, and the Ti-35%Nb-10%Mo-10%CPP alloy had better biocompatibility and corrosion resistance than the Ti-6Al-4V ELI alloy.