• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.3
• /
• pp.206-210
• /
• 2010

$BaTiO_3$ dielectric ceramics are widely used to multi-layer ceramic capacitor. The $BaTiO_3$ powder was synthesized at $950^{\circ}C$ by using a solid state reaction and grinded by using a high-energy mill. And then, 2.53 wt% glass frit was added to the synthesized $BaTiO_3$ powders for lowering the sintering temperature. The mixed powders were sintered at various temperatures of $1170^{\circ}C$, $1200^{\circ}C$, $1230^{\circ}C$. Microstructures of the sintered $BaTiO_3$ ceramics were inspected by SEM and crystal structures were analyzed by XRD method. The relative dielectric constant was measured by using a impedance/gain phase analyzer. The synthesized $BaTiO_3$ powder had the tetragonal perovskite structure without secondary phase and the particle size was below 200 nm. The relative densities measured at the samples sintered at the temperature above $1200^{\circ}C$ were about 95%. The relative dielectric constant showed maximum value of 2310, which was measured in the specimen sintered at $1200^{\circ}C$. From these results, we could know that the added glass frit had effects on both lowering the sintering temperature and improving the dielectric property.

• Journal of the Korean Ceramic Society
• /
• v.22 no.4
• /
• pp.61-65
• /
• 1985

$BaTiO_3$ powders doped with $BaTiO_3$ and $Nb_2O_5$ at 9$0^{\circ}C$ for 1hr. were synthesized by Direct Wet Process. These powders were very homogeneous and fine particle size. To obtain the highe PTCR effect AST($1/3Al_2O_3$.$3/4SiO_2$.$1/4TiO_2$) and $MnO_2$ were added in the semiconduc-ting $BaTiO_3$. In this case $Bi_2O_3$ and $MnO_2$ were used in the form of $Bi(NO)_3$ and $MnCl_2$.$4H_2O$ solution for Direct Wet Process. $BaTiO_3$ doped Nb2O5 and $MnO_2$ demostrated greater PTCR effect than $BaTiO_3$ doped $Nn_2O_5$ only.

• Proceedings of the KWS Conference
• /
• 2005.11a
• /
• pp.201-203
• /
• 2005

A kinetic model for particle coarsening behavior in the weld heat affected zone (HAZ) was proposed. Unlike the conventional approach, where the mean-sized particle is considered to grow continuously, the proposed model considered the critical particle size which can be derived from the Gibbs-Thomson equation. In this study, the proposed particle coarsening model was applied to study the behavior of (Ti, Nb )(C, N) complex particle in the weld HAZ. The predicted particle size distributions using the proposed model were in agreement with the experimental results.

• Journal of the Korean Ceramic Society
• /
• v.41 no.7
• /
• pp.548-554
• /
• 2004

A sol-gel method was applied to coat TiO$_2$ on porous silica prepared using slurry foaming method from silica. from the results of XRD, SEM, and BET, the anatase phase was firstly observed at the coated supports with the heated of 50$0^{\circ}C$. The coated supports with the heated of $700^{\circ}C$ had the maximum anatase peak, and the particle size of coated TiO$_2$ was about 1 ${\mu}{\textrm}{m}$. Bending strength and gas permeability of the porous silica were measured for the feasibility as a catalytic supports. In case of the uncoated porous materials with the strength of 2.4 MPa, the strength increased to 3.9∼4.3 MPa after the coating process regardless of the heating temperature. On the other hand, the permeability of the uncoated porous materials decreased from 770${\times}$10$^{-13}$ $m^2$ to 363${\times}$10$^{-13}$ $m^2$ after the coating process, and it decreased with the increasing heating temperature.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.9
• /
• pp.932-938
• /
• 2005

[ $TiO_2$ ] nanoparticles were prepared from the precipitation in $TiCl_4$ and the sol-gel profess in $Ti(OC_3H_7)_4$ as starting materials with various synthetic conditions. The samples were characterized by XRD, SEM, and TEM testing techniques. The photocatalytic degradation of congo red has been investigated in $TiO_2/UV$ process to evaluate photocatalytic activities for the samples. $TiO_2$ nanoparticles calcined at $400^{\circ}C$ had the best photocatalytic activity with the rate constant of the degradation of congo red as $0.0319\;min^{-1}$. The rate constant of $TiO_2$ photocatalysts was increased with the calcination temperature under $400^{\circ}C$ and decreased with the calcination temperature upper $400^{\circ}C$. In the case of $TiO_2$ photocatalysts, the photocatalytic activity wasn't greatly affected by the frequencies of usage. In the similar synthesis condition, the degradation efficiency of the $TiO_2$ particle prepared by $TiCl_4$ was increased to 8.8%, when the rate was compared with the sample prepared by $Ti(OC_3H_7)_4$. The photocatalytic activities of $TiO_2$ photocatalysts synthesized by $Ti(OC_3H_7)_4$ with various conditions were also discussed.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.309-312
• /
• 2007

Sputter deposition followed by surface treatment was studied using reactive RF plasma as a method for preparing titanium oxide($TiO_{2}$) films on indium tin oxide(ITO) coated glass substrate for dye-sensitized solar cells(DSSCs). Anatase structure $TiO_{2}$ films deposited by reactive RF magnetron sputtering under the conditions of $Ar/O_{2}$(5%) mixtures, RF power of 600W and substrate temperature of $400^{\circ}C$ were surface-treated by inductive coupled plasma(ICP) with $Ar/O_{2}$ mixtures at substrate temperature of $400^{\circ}C$, and thus the films were applied to the DSSCs, The $TiO_{2}$ Films made on these exhibited the BET specific surface area of 95, the pore volume of $0.3cm^{2}$ and the TEM particle size of ${\sim}25$ nm. The DSSCs made of this $TiO_{2}$ material exhibited an energy conversion efficiency of about 2.25% at $100mW/cm^{2}$ light intensity.

• Journal of Environmental Science International
• /
• v.19 no.5
• /
• pp.577-584
• /
• 2010

The generation of $TiO_2$ nanoparticles by a thermal decomposition of titanium tetraisopropoxide (TTIP) was carried out experimentally using a tubular electric furnace at various synthesis temperatures (700, 900, 1100 and $1300^{\circ}C$) and precursor heating temperatures (80, 95 and $110^{\circ}C$). Effects of degree of crystallinity, surface area and anatase mass fraction of those $TiO_2$ nanoparticles on photocatalytic properties such as decomposition of methylene blue was investigated. Results show that the primary particle diameter obtained from thermal decomposition of TTIP was considerably smaller than the commercial photocatalyst (Degussa, P25). Also, those specific surface areas were more than 134.4 $m^2$/g. Resultant $TiO_2$ nanoparticles showed improved photocatalytic activity compared with Deggusa P25. This is contributed to the higher degree of crystallinity, surface area and anatase mass fraction of $TiO_2$ nanoparticles compared with P25.

• Korean Journal of Metals and Materials
• /
• v.47 no.3
• /
• pp.147-154
• /
• 2009

The effect of carbon addition on the microstructures and mechanical properties of $Ni_3Al$ and TiAl intermetallic alloys have been characterized. It is shown that carbon is not only an efficient solid solution strengthener in $Ni_3Al$ and TiAl, it is also an efficient precipitation strengthener by fine dispersion of carbide. Transmission electron microscope investigation has been performed on the particle-dislocation interactions in $Ni_3Al$ and TiAl intermetallics containing various types of fine precipitates. In an $L1_2$-ordered $Ni_3Al$ alloy with 4 mol.% of chromium and 0.2~3.0 mol.% of carbon, fine octahedral precipitates of $M_{23}C_6$ type carbide, which has the cube-cube orientation relationship with the matrix, appear during aging. Typical Orowan loops are formed in $Ni_3Al$ containing fine dispersions of $M_{23}C_6$ particles. In the L10-ordered TiAl containing 0.1~2.0 mol.% carbon, TEM observations revealed that needle-like precipitates, which lie only in one direction parallel to the [001] axis of the $L1_0$ matrix, appear in the matrix and preferentially at dislocations. Selected area electron diffraction (SAED) patterns analyses have shown that the needle-shaped precipitate is $Ti_3AlC$ of perovskite type. The orientation relationship between the $Ti_3AlC$ and the $L1_0$ matrix is found to be $(001)_{Ti3AlC}//(001)_{L10\;matrix}$ and $[010]_{Ti3AlC}//[010]_{L10\;matrix}$. By aging at higher temperatures or for longer period at 1073 K, plate-like precipitates of $Ti_2AlC$ with a hexagonal structure are formed on the {111} planes of the $L1_0$ matrix. The orientation relationship between the $(0001)_{Ti2AlC}//(111)_{L10\;matrix}$ is and $[1120]_{Ti2AlC}//[101]_{L10\;matrix}$. High temperature strength of TiAl increases appreciably by the precipitation of fine carbide. Dislocations bypass the carbide needles at further higher temperatures.

• Korean Journal of Materials Research
• /
• v.17 no.11
• /
• pp.587-592
• /
• 2007

Al-42wt%Nb powder was prepared by high-energy mechanical milling(HEMM). The particle size, phase transformation and microstructure of the as-milled powder were investigated by particle size distribution (PSD) analyzer, scanning electron microscopy (SEM), X-ray diffractometery (XRD), transmission electron microscopy (TEM)and differential thermal analysis (DTA). The milled powders were heated to a sintering temperature at 1000C with under vaccum with vaccum tube furnace. Microstructural examination of sintered Ti-42wt%Nb alloy using 4h-milled powder showed Ti-rich phases (${\alpha}$-Ti) which are fine and homogeneously distributed in the matrix (Nb-rich phase: ${\beta}$-Ti). The sintered Ti-42wt%Nb alloy with milled powder showed higher hardness. The microstructure of the as quenched specimens fabricated by sintering using mixed and milled powder almost are same, but the hardness of as quenched specimen fabricated by using mixed powder increased due to solution hardening of Nb in Ti matrix. The aging effect of these specimens on microstructural change and hardening is not prominent.

• Journal of the Korean Ceramic Society
• /
• v.31 no.8
• /
• pp.835-840
• /
• 1994

In this study, the synthesis of Ba2Ti9O20 powder having chemically homogeneous and highly pure fine particle size distribution was attempted by the oxalate method. And the effects of ZrO2 addition was investigated. The four compositions (X=0, 0.028, 0.048, 0.068) of Ba2(Ti9-x, Zrx)O20 were prepared by precipitation reaction of BaCl2, TiCl4, and ZrOCl2, with oxalic acid and NH4OH acting as a precipitating agent and a pH regulator respectively, in aqueous solution. In case of 4.8 mol% ZrO2 addition, the single phase Ba2Ti9O20 was obtained at 120$0^{\circ}C$ and its dielectric properties was excellent showing K=40.5, Q=4621 at 5.4 GHz.