• Journal of Welding and Joining
• /
• v.18 no.5
• /
• pp.105-111
• /
• 2000

The wear behavior of thermal sprayed AlSiMg-40TiC composite coatings were studied as a function of load and sliding velocity under unlubricated conditions. Experiments were performed using a block-on-ring(WC-6wt%/Co, Hv 1500) type. The tests were carried out a various load(30∼ 125.5N) and sliding velocity(0.5∼2.0m/s). Three wear rate regions were observed in the AlSiMg-40TiC composite coatings. The wear rate in region I at low load (less then 8N( were less than 1×{TEX}$10^{-5}${/TEX}㎣/m. Low wear rates in region I resulted from the load-bearing capacity of TiC particles. The transition from region I to II occurred when the applied load exceeded the fracture and pull-out strength of the particles. The TiC fractured particles trapped between the specimen and the counterface acted as third-body abrasive wear. The subsurface layer worn surface in region II was composed of the mechanically mixed layer (MML). The wear rate increase abruptly above a critical load (region III). The high wear rate in region III was induced by frictional temperature and involves massive surface damage.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.75-78
• /
• 1996

The deposition condition Gf TiN films as electrode was studied by sheet resistance, TiN depositon Thickness X-ray diffraction. TiN was made by reactively DC magnetron sputtering with varying $N_2$/Ar mixture gas and substrate temperature. After finding The deposition condition of TiN films, The samples with the structure of Cu/Ta$_2$O$_{5}$, TiN/Ta$_2$O$_{5}$Si, Cu/TiN/Ta$_2$O$_{5}$ Si were prepared and were measured I-V, C-V. As a results, it was found that when TiN was deposited in an $N_2$a results, it was found that when TiN was deposited in an $N_2$atmosphere its Sheet resistance is lower n than n V$_2$Ar mixtureixture

• Journal of the Korean Vacuum Society
• /
• v.6 no.1
• /
• pp.28-35
• /
• 1997

Effects of rapid thermal annealing on the characteristics of Cu films deposited from the (hfac)Cu(VTMS) precursor and on the barrier properties of TiN layers were studied. By the post-annealing, the electrical characteristics of Cu/TiN and the microstructures of Cu films were significantly changed. The properties of Cu films were more sensitive to the annealing temperature than the annealing time. Sheet resistance started to increase above $400^{\circ}C$, and the interreaction between Cu and Ti and the oxidation of Cu layer were observed above $600^{\circ}C$. The grain growth of Cu with the (111) preferred orientation was found to be most pronounced at $500^{\circ}C$. It revealed that the optimum annealing conditions for MOCVD-Cu/PVD-TiN structures to enhance the electrical characteristics without degradation of TiN barriers were in the range of $400^{\circ}C$.

• Journal of IKEEE
• /
• v.20 no.2
• /
• pp.177-180
• /
• 2016

The effect of varying thickness of Ag/Ti metal bilayer and annealing time have investigated for controlling self-organized nanoparticles (NPs) on 4H-SiC substrate. In addition, Glass and Si substrate which have different surface energy from SiC were fabricated for analyzing interaction of agglomeration. The results of FE-SEM indicated the different formation behaviors of NPs in various ranges of fabrication condition. The surface energy was measured by using a Contact Angle Analyzer. The formation of network-like NPs was observed on Glass and 4H-SiC, respectively, whereas it was not the case on Si substrates. It has been found that the size of NPs increases with decreasing surface energy, due to particle size-dependent hydrophilic properties of substrates. The different formation behavior was explained by using Young's equation for the contact angles between the metal and different substrates.

• Korean Journal of Materials Research
• /
• v.10 no.1
• /
• pp.21-28
• /
• 2000

Refractory metals, W and Ti, and their nitrides, $W_2N$ and TiN, were investigated for using as an ohmic contact material with SiC single crystalline thin films. The possibility of nitride materials for using as a stable ohmic contact material of SiC at high temperatures was examined by considering the thermal stability depending on the heat treatment temperature, their electrical properties and protective behavior from the interdiffusion. W contact with SiC thin films, deposited by using new organosilicon precursor, bis-trimethylsilylmethane, showed the lowest resistivity, $2.17{\times}10^{-5}$Ω$\textrm{cm}^2$. On the other hand, Ti-based contact materials showed higher contact resistivity than W-based ones. The oxidation of contact materials was restricted by applying Pt thin films on those electrodes. Nitride electrodes had rather stable electrical properties and better protective behavior from interdiffusion than metal electrodes.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.211-211
• /
• 1999

Titanium nitride (TiN) thin films have useful properties including high hardness, good electrical conductivity, high melting point, and chemical inertness. The applications have included wear-resistant hard coatings on machine tools and bearings, decorative coating making use of the golden color, thermal control coatings for widows, and erosion resistant coatings for spacecraft plasma probes. For all these applications as feature sizes shrink and aspect ratios grow, the issue of good step coverage becomes increasingly important. It is therefore essential to manufacture conformal coatings of TiN. The growth of TiN thin films by chemical vapor deposition (CVD) is of great interest for achieving conformal deposition. The most widely used precursor for TiN is TiCl4 and NH3. However, chlorine impurity in the as-grown films and relatively high deposition temperature (>$600^{\circ}C$) are considered major drawbacks from actual device fabrication. To overcome these problems, recently, MOCVD processes including plasma assisted have been suggested. In this study, therefore, we have doposited Ti(C, N) thin films on Si(100) and D2 steel substrates in the temperature range of 150-30$0^{\circ}C$ using tetrakis diethylamido titanium (TDEAT) and titanium isopropoxide (TIP) by pulsed DC plamsa enhanced metal-organic chemical vapor deposition (PEMOCVD) method. Polycrystalline Ti(C, N) thin films were successfully grown on either D2 steel or Si(100) surfaces at temperature as low as 15$0^{\circ}C$. Compositions of the as-grown films were determined with XPS and RBS. From XPS analysis, thin films of Ti(C, N) with low oxygen concentration were obtained. RBS data were also confirmed the changes of stoichiometry and microhardness of our films. Radical formation and ionization behaviors in plasma are analyzed by optical emission spectroscopy (OES) at various pulsed bias and gases conditions. H2 and He+H2 gases are used as carrier gases to compare plasma parameter and the effect of N2 and NH3 gases as reactive gas is also evaluated in reduction of C content of the films. In this study, we fond that He and H2 mixture gas is very effective in enhancing ionization of radicals, especially N resulting is high hardness. The higher hardness of film is obtained to be ca. 1700 HK 0.01 but it depends on gas species and bias voltage. The proper process is evident for H and N2 gas atmosphere and bias voltage of 600V. However, NH3 gas highly reduces formation of CN radical, thereby decreasing C content of Ti(C, N) thin films in a great deal. Compared to PVD TiN films, the Ti(C, N) film grown by PEMOCVD has very good conformability; the step coverage exceeds 85% with an aspect ratio of more than 3.

• Journal of Korean Ophthalmic Optics Society
• /
• v.5 no.1
• /
• pp.7-11
• /
• 2000

The anti-reflective anti-static (ARAS) optical film is designed using absorbent materials such as ITO, $TiN_xW_y$, Ag by Essential Macleod program. [air ${\mid}TiN_xW_y{\mid}SiO_2{\mid}$ glass] two layer shows wide-band AR coating in the wavelength range of 450~700 nm. The reflectivity, transmittance of this coating are below 0.5%, about 75%, respectively. [air $SiO_2{\mid}TiO_2{\mid}SiO_2{\mid}$, ITO glass] layer can adjust reflectance of below 0.5% with above 97% transmittance. In the [air ${\mid}SiO_2{\mid}TiO_2{\mid}SiO_2{\mid}$ Ag glass] layer, the transmission can be controlled at above 96% with reflectance of 1~2%.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.266-267
• /
• 2011

질화갈륨(GaN)은 높은 전자이동도 및 높은 항복전계를 가지며 낮은 온저항으로 인하여 에너지효율이 우수하기 때문에 고출력 전력소자 분야에서 많은 관심을 받고 있다. GaN을 이용한 고출력 전력소자의 경우 상용화 수준에 근접할 만한 기술적 진보가 있었으나, 페르미 레벨 고정(Fermi-level pinning) 현상, 소자의 누설전류 등 아직 해결되어야 할 문제를 갖고 있다. 본 연구에서는 실리콘 기판 위에 성장된 GaN 에피탁시를 활용한 고출력 전력소자의 누설전류를 억제시키기 위해 오믹 접합 중 Au의 상호확산을 억제하는 중간층 금속(Mo or Ni)을 변화시켰으며 오믹 열처리 온도에 따른 특성을 비교 연구하였다. $Cl_2$와 $BCl_3$를 이용하여 0.6 ${\mu}m$ 깊이의 메사 구조가 활성영역을 형성하였고, Si 도핑된 n-GaN 위에 Ti/Al/Mo/Au (20/100/25/200 nm) 와 Ti/Al/Ni/Au (20/100/25/200 nm) 오믹 접합을 각각 설계, 제작하였다. 오믹 열처리시의 GaN 표면오염을 방지하기 위해 $SiO_2$ 희생층을 증착하였다. 오믹 접합 형성을 위해 각 750$^{\circ}C$, 800$^{\circ}C$, 850$^{\circ}C$에서 30초간 열처리를 진행 하였으며, 이후 6 : 1 BOE 용액으로 $SiO_2$ 희생층을 제거하였다. 750, 800, 850$^{\circ}C$에서 Ti/Al/Mo/Au 구조의 오믹 접합 저항은 각 2.56, 2.34, 2.22 ${\Omega}$-mm 이었으며, Ti/Al/Ni/Au 구조의 오믹 접합 저항은 각 43.72, 2.64, 1.86 ${\Omega}$-mm이었다. Isolation 누설전류를 측정하기 위해서 두 개의 오믹 접합 사이에 메사 구조가 있는 테스트 구조를 제안하였다. Isolation 누설전류는 Ti/Al/Mo/Au 구조에서 두 오믹 접합 사이의 거리가 25 ${\mu}m$이고 100 V일 때 750, 800, 850 $^{\circ}C$의 열처리 온도에서 각 1.25 nA/${\mu}m$, 2.48 nA/${\mu}m$, 8.76 nA/${\mu}m$이었으며, Ti/Al/Ni/Au 구조에서는 각 1.58 nA/${\mu}m$, 2.13 nA/${\mu}m$, 96.36 nA/${\mu}m$이었다. 열처리 온도가 증가하며 오믹 접합 저항은 감소하였으나 isolation 누설전류는 증가하였다. 750$^{\circ}C$ 열처리에서 오믹 접합 저항은Ti/Al/Mo/Au 구조가 Ti/Al/Ni/Au 구조보다 약 17배 우수하였고, 850$^{\circ}C$ 고온의 열처리 경우 Ti/Al/Mo/Au 구조의 isolation 누설전류는 8.76 nA/${\mu}m$로 Ti/Al/Ni/Au의 누설전류 96.36 nA/${\mu}m$보다 약 11배 우수하였다. Ti/Al/Mo/Au가 Ti/Al/Ni/Au 보다 오믹 접합 저항과 isolation 누설전류 측면에서 전력용 GaN 소자에 적합함을 확인하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.163-163
• /
• 1999

MOSFET, MESFET 그리고 MODFET는 Logic ULSIs, high speed ICs, RF MMICs 등에서 중요한 역할을 하고 있으며, 그것의 gate electrode, contact, interconnect 등의 물질로는 refractory metal을 이용한 CoSi2, MoSi2, TaSi2, PtSi2, TiSi2 등의 효과를 얻어내고 있다. 그중 TiSi2는 비저항이 가장 낮고, 열적 안정도가 좋으며 SAG process가 가능하므로 simpler alignment process, higher transconductance, lower source resistance 등의 장점을 동시에 만족시키고 있다. 최근 소자차원이 scale down 됨에 따라 TiSi2의 silicidation 과정에서 C49 TiSi2 phase(high resistivity, thermally unstable phase, larger grain size, base centered orthorhombic structure)의 출현과 그것을 제거하기 위한 노력이 큰 issue로 떠오르고 있다. 여러 연구 결과에 따르면 PAI(Pre-amorphization zimplantation), HTS(High Temperature Sputtering) process, Mo(Molybedenum) implasntation 등이 C49를 bypass시키고 C54 TiSi2 phase(lowest resistivity, thermally stable phase, smaller grain size, face centered orthorhombic structure)로의 transformation temperature를 줄일 수 있는 가장 효과적인 방법으로 제안되고 있지만, 아직 그 문제가 완전히 해결되지 않은 상태이며 C54 nucleation에 대한 physical mechanism을 밝히진 못하고 있다. 본 연구에서는 증착 시 기판온도의 변화(400~75$0^{\circ}C$)에 따라 silicon 위에 DC/RF magnetron sputtering 방식으로 Ti/Si film을 각각 제작하였다. 제작된 시료는 N2 분위기에서 30~120초 동안 500~85$0^{\circ}C$의 온도변화에 따라 RTA법으로 각각 one step annealing 하였다. 또한 Al을 cosputtering함으로써 Al impurity의 존재에 따른 영향을 동시에 고려해 보았다. 제작된 시료의 분석을 위해 phase transformation을 XRD로, microstructure를 TEM으로, surface topography는 SEM으로, surface microroughness는 AFM으로 측정하였으며 sheet resistance는 4-point probe로 측정하였다. 분석된 결과를 보면, 고온에서 제작된 박막에서의 C54 phase transformation temperature가 감소하는 것이 관측되었으며, Al impuritydmlwhswork 낮은온도에서의 C54 TiSi2 형성을 돕는다는 것을 알 수 있었다. 본 연구에서는 결론적으로, 고온에서 증착된 박막으로부터 열적으로 안정된 phase의 낮은 resistivity를 갖는 C54 TiSi2 형성을 보다 낮은 온도에서 one-step RTA를 통해 얻을 수 있다는 결과와 Al impurity가 존재함으로써 얻어지는 thermal budget의 효과, 그리고 그로부터 기대할 수 있는 여러 장점들을 보고하고자 한다.

• Journal of the Korean Ceramic Society
• /
• v.46 no.5
• /
• pp.467-471
• /
• 2009

Effects of boron and carbon on the densification and thermal decomposition of an AlN-SiC-$TiB_2$ system were investigated. $SiO_2$ was mostly removed by the addition of carbon, while $Al_2O_3$ formed $Al_4O_4C$ and promoted the densification of the systems above $1850^{\circ}C$. Rather porous specimens were obtained without the additives after hot pressing at $2100^{\circ}C$, while densification was mostly completed at $2000^{\circ}C$ by using the additives. The sintering temperature decreased further to $1950^{\circ}C$ by applying spark plasma sintering. The additives promoted the shrinkage of AlN by forming a liquid phase which was originated from the carbo- and boro-thermal reduction of $Al_2O_3$ and AlN.