• Bulletin of the Korean Chemical Society
• /
• v.33 no.4
• /
• pp.1204-1208
• /
• 2012

A new photoelectrode composed of $Sb_6O_{13}$ nanoparticles with the size of 20-30 nm has been prepared via thermolysis of a colloidal antimony pentoxide tetrahydrate ($Sb_2O_5{\cdot}4H_2O$) suspension. The $Sb_6O_{13}$ electrode showed good semiconducting properties applicable to dye-sensitized solar cells (DSSCs); the energy band gap was estimated to be $3.05{\pm}0.5$ eV and the position of conduction band edge was close to those of $TiO_2$ and ZnO. The DSSC assembled with the $Sb_6O_{13}$ photoelectrode and a conventional ruthenium-dye (N719) exhibited the overall photo-current conversion efficiency of 0.74% ($V_{oc}$ = 0.76 V, $J_{sc}=1.99\;mAcm{-2}$, fill factor = 0.49) under AM 1.5, $100\;mWcm^{-2}$ illumination.

• Transactions of the Korean hydrogen and new energy society
• /
• v.10 no.4
• /
• pp.197-210
• /
• 1999

The hydrogen storage performance and electrochemical properties of $Zr_{1-X}Ti_X(Mn_{0.2}V_{0.2}Ni_{0.6})_{1.8}$(X=0.0, 0.2, 0.4, 0.6) alloys are investigated. The relationship between discharge performance and alloy characteristics such as P-C-T characteristics and crystallographic parameters is also discussed. All of these alloys are found to have mainly a C14-type Laves phase structure by X-ray diffraction analysis. As the mole fraction of Ti in the alloy increases, the reversible hydrogen storage capacity decreases while the equilibrium hydrogen pressure of alloy increases. Furthermore, the discharge capacity shows a maxima behavior and the rate-capability is increased, but the cycling durability is rapidly degraded with increasing Ti content in the alloy. In order to analyze the above phenomena, the phase distribution, surface composition, and dissolution amount of alloy constituting elements are examined by S.E.M., A.E.S. and I.C.P. respectively. The decrease of secondary phase amount with increasing Ti content in the alloy explains that the micro-galvanic corrosion by multiphase formation is little related with the degradation of the alloys. The analysis of surface composition shows that the rapid degradation of Ti-substituted Zr base alloy electrode is due to the growth of oxygen penetration layer. After comparing the radii of atoms and ions in the electrolyte, it is clear that the electrode surface becomes more porous, and that is the source of growth of oxygen penetration layer while accelerating the dissolution of alloy constituting elements with increasing Ti content. Consequently, the rapid degradation (fast growth of the oxygen-penetrated layer) with increasing Ti substitution in Zr-based alloy is ascribed to the formation of porous surface oxide through which the oxygen atom and hydroxyl ion with relatively large radius can easily transport into the electrode surface.

• Journal of the Korean institute of surface engineering
• /
• v.31 no.3
• /
• pp.133-141
• /
• 1998

Stainless is widely used for various purposes due to its good corrosion resistance. There has been much research to produce the color stainless steel by several methods. In this experiment, TixN films have been deposited on the SUS304 substrate by the DC magnetron sputtering system and the color and texture of the films as a function of coating conditions has been studies. The TixN films showed a (111) preferred orintation in bias-free conditions. The texture of coated later was changed from (111) to (200) to (2200 with a change of the bias from -1000V to -3000V. When the bias is low, coated elements have low energy. Therefore, the texturct (111) of low surface energy. The mobility of atoms was increased with the increase of the blas and texture was changed to the other plane. Non-etched specimens all exhibited strong (111) texture. This result shows that (111) is a loose plane and of non-etched specimens all exhibited. High growing velocity of (111) of especially was main texture of Non-etched specimens. Low working pressure($4\times10^{-3}$torr) was more effective than figh working pressure ($6\times10^{-3}$torr) for the gold color of $Ti_xN$ film. L and b were increased and a was decreased with the increase of bias voltage. Accordingly, We obtained the near gold color of $Ti_xN$ film(L;92, a;1~1.5 b:24~29.50. As a result of reflectance. And as the bias increased, the reflectance was proportional to the increasing bias voltage, but we took the top reflectance when the bias voltage was -200V.

• The Korean Journal of Ceramics
• /
• v.6 no.3
• /
• pp.291-295
• /
• 2000

The pyroelectric property of $Pb_{0.9}La$_{0.1}TiO_3$ceramics in a range of 1.3-4.1$\mu\textrm{m}$, fabricated by conventional solid sintering, was investigated as a function of poling field. The pyroelectric of the 4.1$\mu\textrm{m}$ of $Pb_{0.9}La$_{0.1}TiO_3$ceramics is higher than that of the 1.3$\mu\textrm{m}$ and 1.7$\mu\textrm{m}$ of $Pb_{0.9}La$_{0.1}TiO_3$ceramics at a low poling field and the pyroelectric coefficient is 25nC/$\textrm{cm}^2$K at a 4kV/mm poling field in every grain size. In order to explain this phenomenon, the intrinsic and extrinsic effects in view of the definition of the pyroelectric coefficient are introduced. The intrinsic and extrinsic effects on the pyroelectric property were investigated by measuring the tetragonal ratio and the $I_{002}$ with temperature with high temperature X-ray diffractometer. The change of spontaneous polarization and the $90^{\circ}$domain wall motion with temperature in the 1.3$\mu\textrm{m}$ and 4.2$\mu\textrm{m}$ of $Pb_{0.9}La$_{0.1}TiO_3$ceramics have no effects on the pyroelectric coefficient. In our study, it can be seen that the pyroelectric coefficient is related to the quantity of $180^{\circ}$domain switching after poling treatment.

• Journal of Ceramic Processing Research
• /
• v.20 no.6
• /
• pp.603-608
• /
• 2019

In this study, the multilayered thin films of (Ba,Sr)TiO3/K(Ta,Nb)O3 were fabricated by the sol-gel and spin coating methods, and their structural and electrical properties were investigated. The specimen showed polycrystalline X-ray diffraction (XRD) characteristics with a tetragonal structure. The average grain size and film thickness for one coating were about 30~40nm and 60nm, respectively. The phase transition temperature of specimen was lower than 10 ℃. The dielectric constant and loss at 20 ℃ of the specimen coated six times were 1,231 and 0.69, respectively. The rate of change in dielectric constant at an applied direct current (DC) voltage of the six times coated thin films was 17.3%/V. The electrocaloric effect was the highest around the temperature at which the remanent polarization rapidly changed. When an electric field of 660kV/cm was applied to the triply coated thin films, the highest electrocaloric property of 4.41 ℃ was observed.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.8
• /
• pp.80-90
• /
• 1994

The ultra shallow junction was formed by 2-step RTP. Phosphorus solid source(P$_{2}O_{5}$) was transfered on wafer surface during RTG(Rapid Thermal Glass Transfer) of which process condition was 80$0^{\circ}C$ and 60sec. The process temperature and time of the RTD(Rapid Thermal Diffusion) were 950~105$0^{\circ}C$ during 5~15sec respectively sheet resistances were measured as 175~320$\Omega$/m and junction depth and dopth and dopant surface concentration were measured as 0.075~0.18$\mu$m and 5${\times}10^{19}cm^{4}$ respectively. Ti-silicide was formed by 2-step RTA after 300$\AA$ Titanium was deposited. The 1st RTA (2nd RTA) was carried out at the temperature of $600^{\circ}C$(700~80$0^{\circ}C$) for 30 seconds (10~60 seconds) under N$_2$ ambient. Sheet resistances after 2nd RTA were measured as 46~63$\Omega$/D. Si/Ti component ratio was evaulated as 1.6~1.9 from Auger depth profile. Ti-Silicided n-p junction diode (pattern size : 400$\times$400$\mu$m) was fabricated under the RTD(the process was carried out at the temperature of 100$0^{\circ}C$ for 10seconds) and 2nd RTA(theprocess was carried out at the temperature of 750$^{\circ}C$ for 60 seconds). Leakage current was measured 1.8${\times}10^{7}A/mm^{2}$ at 5V reverse voltage. Whent the RTD process condition is at the temperature of 100$0^{\circ}C$ for 10seconds and the 2nd RTA process condition is at the temperature of 75$0^{\circ}C$ for 60 seconds leakage current was 29.15${\times}10^{9}A$(at 5V).

• Korean Journal of Optics and Photonics
• /
• v.4 no.1
• /
• pp.47-56
• /
• 1993

Practical efficiencies of pulsed gas discharge lasers utilizing vaporized Au, Ba, Cu, Fe, Mn, Pb, TI atoms are numerically optimized for a discharge pulse of 30 ns rise time at 5 kHz pulse repetition rate. Calculated optimum operating temperatures are close to the values at which the vapor pressure of each atom is about 1 Torr and are in good agreement with experimental values reported elasewhere. The optimum charging voltage was about 4 kV for all atomic vapor lasers except the TI laser. The calculated maximum efficiencies that have been discussed for possible limiting efficiencies for each laser were considerably higher than the reported experimental values. Especially, they were as high as 6.8% for Mn laser and 15% for Ba laser that were comparable to the 8.5% of copper vapor laser, from which considerably higher efficiencies can be expected for these two lasers experimentally. But, the present calculation shows a very low efficiency of 0.058% and requires an exceptional operating condition for the TI laser.

• Journal of Sensor Science and Technology
• /
• v.6 no.1
• /
• pp.1-5
• /
• 1997

Highly sensitive pyroelectric IR sensors were fabricated with La-modified $PbTiO_{3}(PLT)$ thin plates compensating for piezoelectric effect. The device was fabricated in a dual form by placing two PLT cells, each of $1{\times}2\;mm^{2}$, side by side with appropriate electrode configuration. The dual element sensor had a signal to noise ratio of about 350 that was much larger than that of single element sensors. Further the dual element sensors exhibited excellent pyroelectric properties such as a large voltage responsivity of 2400 V/W, a pyro-coefficient of $4.6{\times}10^{-8}\;C/cm^{2}K$, a voltage figure of merit of $4.2{\times}10^{-11}\;Ccm/J$, and a small thermal time constant of 8.7 msec. It was confirmed through experiments that the dual element sensor was applicable to detect the two-dimensional moving direction of human beings.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2003.11a
• /
• pp.221-225
• /
• 2003

The MFIS-FET(Field Effect Transistor) devices using $BLT/Y_2O_3$ buffer layer on p-Si(100) substrates were fabricated by the Sol-Gel method and conventional memory processes. The crystal structure, morphologies and electrical properties of prepared devices were investigated by using various measuring techniques. From the C-V(capacitance-voltage) data at 5V, the memory window voltage of the $Pt/BLT/Y_2O_3/si$ structure decreased from 1.4V to 0.6V with increasing the annealing temperature from $700^{\circ}C\;to\;750^{\circ}C$. The drain current (Ic) as a function of gate voltages $(V_G)$ for the $MFIS(Pt/BLT/Y_2O_3/Si(100))-FET$ devices at gate voltages $(V_G)$ of 3V, 4V and 5V, the memory window voltages increased from 0.3V to 0.8V as $V_G$ increased from 3V to 5V.

• Journal of the Korean Electrochemical Society
• /
• v.5 no.3
• /
• pp.106-110
• /
• 2002

Gel-type polyacrylonitrile(PAN) polymer electrolytes have been prepared using ethylene carbonate(EC), propylene carbonate(PC) and dimethyl carbonate(DMC) plasticizer, $LiPF_6$ salt and $TiO_2$ ceramic filler. Electrochemical properties, such as electrochemical stability, ionic conductivity and compatibility with lithium metal and mechanical properly of polymer electrolytes were investigated. Charge/discharge performance of lithium secondary battery using these polymer electrolytes were investigated. The maximum load that the polymer electrolyte resists increased about two times as a result of adding $TiO_2$ in the polymer electrolyte containing EC and PC. Polymer electrolyte containing EC, PC and $TiO_2$ also showed ionic conductivity of $2\times10^{-3} S/cm$ at room temperature and electrochemical stability window up to 와 4.5V. Polymer electrolyte containing EC, PC, and $TiO_2$ showed the most stable interfacial resistance of $130\Omega$ during 20 days in the impedance spectra of the cells which were constructed by lithium metals as electrodes. Lithium metal secondary battery which employed $LiCoO_2$ cathode, lithium metal anode and $TiO_2$-dispersed polymer electrolyte showed $90\%$ of charge/discharge efficiency at the 1C rate of discharge.