• Journal of Powder Materials
• /
• v.11 no.2
• /
• pp.165-170
• /
• 2004

Growth behavior of two different types of grains, faceted and rounded, in a liquid matrix has been studied in the (75WC-25TiCN)-30Co system. Powder samples were sintered above the eutectic temperature for various times under a carbon saturated condition. (Ti,W)(C,N) grains with a rounded shape and WC grains with a faceted shape coexisted in the same Co based liquid. With increasing sintering time, the average size of (Ti.W)(C,N) grains increased continuously and very large WC grains appeared. The growth of rounded (Ti,W)(C,N) grains followed a cubic law, r^3-r^3_0$=kt, where r is the average size of the grains, $r_0$ the initial average size, k the proportionality constant and t the sintering time. indicating a diffusion-controlled growth. On the other hand, the growth of the faceted WC grains resulted in a bimodal grain size distribution, showing an abnormal grain growth. These observations show that the growth behavior of different types of grains is governed by their shape, faceted or rounded, even in the same liquid matrix.

• Journal of Powder Materials
• /
• v.29 no.4
• /
• pp.325-331
• /
• 2022

Beta-titanium alloys are used in many industries due to their increased elongation resulting from their BCC structure and low modulus of elasticity. However, there are many limitations to their use due to the high cost of beta-stabilizer elements. In this study, biocompatible Ti-Mo-Fe beta titanium alloys are designed by replacing costly beta-stabilizer elements (e.g., Nb, Zr, or Ta) with inexpensive Mo and Fe elements. Additionally, Ti-Mo-Fe alloys designed with different Fe contents are fabricated using powder metallurgy. Fe is a strong, biocompatible beta-stabilizer element and a low-cost alloying element. The mechanical properties of the Ti-Mo-Fe metastable beta titanium alloys are analyzed in relation to the microstructural changes. When the Fe content increases, the tensile strength and elongation decrease due to brittle fracture despite a decreasing pore fraction. It is confirmed that the hardness and tensile strength of Ti-5Mo-2Fe P/M improve to more than 360 Hv and 900 MPa, respectively.

• Journal of the Korean Ceramic Society
• /
• v.31 no.9
• /
• pp.1005-1011
• /
• 1994

The three different composition of BaTi4O9, Ba2Ti9O20 and BaTi5O11 were prepared by coprecipitation process, and then the dielectric properties of these compounds were measured at low microwave frequencies. The powder showing high level of purity was synthesised by the coprecipition reaction of BaCl2 and TiCl4 where (NH4)2CO3 and NH4OH were used as a deflocculent. Followings are the result of this study: 1. The sintering temperature increased with increasing TiO2 content. 2. BaTi4O9 powder were synthesized as a single phase by this processing technique, but the resultant Ba2Ti9O20 and BaTi5O11 phase existed with Ba2Ti9O20 and BaTi5O11 phases. 3. Single phase BaTi4O9 showed high dielectric constant value of 35, high Q value of 8100.

• Analytical Science and Technology
• /
• v.20 no.4
• /
• pp.302-307
• /
• 2007

The reaction morphology was investigated depending on the amounts of HCl and $NH_4OH$, and the effect of pH was studied on the preparation of $TiO_2$ nanopowders. $TiO_2$ nanopowder was prepared using a titanium tetra-isopropoxide. Subsequently, the effect of pH on the characteristics of the prepared $TiO_2$ nanopowder was evaluated depending on the amounts of the catalysts such as HCl and $NH_4OH$. The morphology and phase transformation of $TiO_2$ powder prepared by hydrolysis of titanium tetra-isopropoxide were strongly influenced by the presence of the catalysts. In the case of using $NH_4OH$, the morphology of the $TiO_2$ powder exhibited powder form. For the HCl catalyst, it showed bulk or granule form. The phase transformations of amorphous $Ti(OH)_4$ to anatase $TiO_2$ and the anatase to rutile was significantly influenced by the kind and amount of thecatalysts.

• Applied Chemistry for Engineering
• /
• v.7 no.6
• /
• pp.1105-1114
• /
• 1996

The characteristic and performance of ${\beta}-PbO_2$ layer electrodeposited on ${\alpha}-PbO_2/IrO_2-TiO_2/Ti$ substrate by adding sodium lauryl sulfate and $TiO_2$ powder in lead nitrate solution were investigated by using XRD, SEM, cyclic voltammograms, and macro-elctrolysis. Results of XRD analysis ascertain that ${\beta}-PbO_2$ layers electrodeposited in the presence of sodium lauryl sulfate and $TiO_2$, powder on ${\alpha}-PbO_2/IrO_2-TiO_2/Ti$ substrate have the same tetragonal structure as pure ${\beta}-PbO_2$ layers. The SEM results show that sodium lauryl sulfate tend to diminish crystal size of the deposited layer. The ${\beta}-PbO_2$ electrode electrodeposited in the presence of sodium lauryl sulfate and $TiO_2$ powder gives significantly improved oxygen overvoltage and durability for anodic oxidation in KOH and $HClO_4$ supporting electrolyte. Electrode performance and durability for the evolution of ozone in perchloric acid solution have been investigated by using ${\beta}-PbO_2$ electrodes electrodeposited on Titanium $madras^{(R)}$. It was ascertained that the $PbO_2$ electrode electrodeposited on ${\alpha}-PbO_2/IrO_2-TiO_2/Ti$ $madras^{(R)}$ by adding sodium lauryl sulfate and $TiO_2$ powder in $HClO_4$ supporting electrolyte had the highest current efficiency and durability.

• Journal of Powder Materials
• /
• v.2 no.2
• /
• pp.165-170
• /
• 1995

Alloying behavior of nanocrystalline Al-Ti-(Si) composite powders via mechanical alloying (MA) has been investigated, and the effect of Si on the microstructural changes during MA was discussed. The microstructures of both MA powders and extruded compacts were examined. In Al-Ti system, the solid solutionized nanocrystalline powders could be obtained by MA. On the contrary, fine Si particles were embedded as an elemental state in the matrix of Al-Ti-Si system because of the brittleness and the negligible solid solubility of Si in Al. After hot extrusion, $Al3Ti$ phase was finely precipitated in Al-10fSTi alloy, and Si particles were dissolved to form $(Al, Si)_3Ti$ phase in Al-10%Ti-2%Si alloy.

• Journal of Technologic Dentistry
• /
• v.32 no.4
• /
• pp.337-340
• /
• 2010

Purpose: This study was performed to compare sintering conditions for fabrication of porous Ti implant. Methods: The porous Ti implant samples were fabricated by sintering of spherical Ti powders in vacuum and atmosphere conditions. Surface morphology, composition and phase were analyzed by FE-SEM, EDX and XRD. Results: Sintered Ti implant in the vacuum consisted of particles connected in three dimensions by clear necking without excessive oxide layers. However, sintered Ti implant in atmosphere was formed excessive oxide layers with non-stoichiometric compounds. Conclusion: The porous Ti implant can be sintered in vacuum condition preferably.

• Journal of Powder Materials
• /
• v.6 no.2
• /
• pp.139-144
• /
• 1999

The pure Ti, Ni and carbon powders were reaction milled to synthesize the TiC-Ni based cermet powders with ultrafine microstructures. After milling, the ultrafine TiC or amorphous Ti-Ni phase was obtained, respectively, according to the milling condition. The effects of milling variables on the synthesizing behavior of the powders were investigated in detail. The sintered TiC-Ni based cermet of the reaction milled powders consisted of very fine TiC of 0.2~1.5$\mu$m, as compared with that of a commercial cermet of 3~5$\mu$m. This demonstrates the potenial of reaction milling as an effective processing route for the preparation of cermet materials.

• Journal of Powder Materials
• /
• v.2 no.1
• /
• pp.36-43
• /
• 1995

Rapidly solidified and mechanically alloyed Al-Ti base alloys were prepared by gas atomization and attritor milling separately. The gas atomized and the mechanically alloyed powders were consolidated after preheating at $450^{\circ}C$, and then heat treated isochronally for 1 hour to observe the microstructures and to investigate the mechanical properties. Stable phases of precipitates in the Al-Ti-Si and the Al-Ti-Zr alloys were identified as DO22-$(Al,Si)_3Ti$ and $Do_{23}-Al_3(Ti, Zr)$ each. Among the alloys, the mechanically alloyed Al-l0Ti-2Si alloy showed superior thermal stability and mechanical properties at elevated temperature. The additions of third elements, such as Si and Zr, to Al-Ti alloys seemed to improve the mechnical properties remarkably by stabilizing the microstructure and the precipitate phases in the consolidated alloys.

• Korean Journal of Materials Research
• /
• v.22 no.3
• /
• pp.150-154
• /
• 2012

Ti-6Al-4V ELI (Extra Low Interstitial) alloy have been widely used as alternative to bone due to its excellent biocompatibility, although it still has many problems such as high elastic modulus and toxicity. Therefore, biomaterials with low elastic modulus and non toxic characteristics have to be developed. A novel ${\beta}$ Ti-35wt%Nb-7wt%Zr-Calcium pyrophosphate (CPP) composite that is a biocompatible alloy without elemental Al or V was fabricated by spark plasma sintering (SPS) at $1000^{\circ}C$ under 70 MPa using high energy mechanical milled (HEMM) powder. The microstructure and phases of the milled powders and the sintered specimens were studied using SEM, TEM, and XRD. Ti-35wt%Nb-7wt%Zr alloy was transformed from ${\alpha}$ phase to ${\beta}$ phase in the 4h-milled powder by sintering. The sintered specimen using the 4h-milled powder showed that all the elements were distributed very homogeneously and had higher density and hardness. ${\beta}$ Ti alloy-CPP composite, which has nanometer particles, was fabricated by SPS using HEMMed powder. During the sintering process, $CaTiO_3$, TixOy, and CaO were formed because of the reaction between Ti and CPP. The Vickers hardness of the composites increases with the increase of the milling time and the addition of CPP. The biocompatibility of the Ti-Nb-Zr alloys was improved by addition of CPP.