• Korean Journal of Materials Research
• /
• v.19 no.2
• /
• pp.61-67
• /
• 2009

Electrolessly deposited Co (Re,P) was investigated as a possible capping layer for Cu wires. 50 nm Co (Re,P) films were deposited on Cu/Ti-coated silicon wafers which acted as a catalytic seed and an adhesion layer, respectively. To obtain the optimized bath composition, electroless deposition was studied through an electrochemical approach via a linear sweep voltammetry analysis. The results of using this method showed that the best deposition conditions were a $CoSO_4$ concentration of 0.082 mol/l, a solution pH of 9, a $KReO_4$ concentration of 0.0003 mol/l and sodium hypophosphite concentration of 0.1 mol/L at $80^{\circ}C$. The thermal stability of the Co (Re,P) layer as a barrier preventing Cu was evaluated using Auger electron spectroscopy and a Scanning calorimeter. The measurement results showed that Re impurities stabilized the h.c.p. phase up to $550^{\circ}C$ and that the Co (Re,P) film efficiently blocked Cu diffusion under an annealing temperature of $400^{\circ}C$ for 1hr. The good barrier properties that were observed can be explained by the nano-sized grains along with the blocking effect of the impurities at the fast diffusion path of the grain boundaries. The transformation temperature from the amorphous to crystal structure is increased by doping the Re.

• Journal of dental hygiene science
• /
• v.9 no.4
• /
• pp.405-412
• /
• 2009

The purpose of this study investigated the effect of Au coating on adhesion between porcelain matrix and metal substructure interface. Titanium, Ni-Cr alloy and Co-Cr alloy are well known as proper metal for the dental restorations. The success of a porcelain fused to metal (PFM) restoration depends upon the quality of the porcelain-metal bond. However, adhesion between dental alloys and porcelain is related to diffusion of oxygen during ceramic firing. The excessive oxidized layers make hard adhesion between dental alloy and ceramic. Ni-Cr and Co-Cr specimens were divided into test and a control group and Titanium specimens were divided into three test groups and a control group. Each group had 20 specimens. The adhesion characteristics of porcelain and metal with Au coating layer and without Au coating layer were observed with scanning electron microscopy(SEM). The adhesion was evaluated by a biaxial flexure test and volume fraction of adherent porcelain was determined by SEM/EDS analysis. Result of this study suggest that Au coating layer is effective barrier to diffuse oxide layer completely protect non-precious alloys from oxidation during the porcelain firing. The SEM photomicrographs of cross-section specimens showed a smooth interface between Au coating layer and metals and porcelain which suggested proper chemical bonding, and no gap, porosity were observed. The mode of failure was mainly adhesive for Ti tested specimens, but mixed failures with adhesive and cohesive were observed in Ni-Cr and Co-Cr specimens. The adhesion between non-precious metals and porcelain would not be improved by Au coating agent. However, It is suggested that the continuous study is required further investigation and development.

• 한국태양에너지학회:학술대회논문집
• /
• 2009.04a
• /
• pp.214-219
• /
• 2009

In high-efficiency crystalline silicon solar cells, If high-efficiency solar cells are to be commercialized. It is need to develop superior contact formation method and material that can be inexpensive and simple without degradation of the solar cells ability. For reason of plated metallic contact is not only high metallic purity but also inexpensive manufacture. It is available to apply mass production. Especially, Nickel, Copper and Silver are applied widely in various electronic manufactures as easily formation is available by plating. The metallic contact system of silicon solar cell must have several properties, such as low contact resistance, easy application and good adhesion. Ni is shown to be a suitable barrier to Cu diffusion as well as desirable contact metal to silicon. Nickel monosilicide(NiSi) has been suggested as a suitable silicide due to its lower resistivity, lower sintering temperature and lower layer stress than $TiSi_2$. Copper and Silver can be plated by electro & light-induced plating method. Light-induced plating makes use the photovoltaic effect of solar cell to deposite the metal on the front contact. The cell is immersed into the electrolytic plating bath and irradiated at the front side by light source, which leads to a current density in the front side grid. Electroless plated Ni/ Electro&light-induced plated Cu/ Light-induced plated Ag contact solar cells result in an energy conversion efficiency of 14.68 % on $0.2{\sim}0.6{\Omega}{\cdot}cm,\;20{\times}20mm^2$, CZ(Czochralski) wafer.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.4
• /
• pp.342-349
• /
• 2009

This study investigated the growth characteristics of carbon nanotubes (CNTs) by changing a period of annealing time and a $C_{2}H_{2}/H_2$ flow ratio at temperature as low as $450^{\circ}C$ with inductively coupled plasma chemical vapor deposition. The 1-nm-thick Fe-Ni-Co alloy thin film served as a catalyst layer for the growth of CNTs, which was thermally evaporated on the 15-nm-thick Al underlayer deposited on the 50-nm-thick Ti diffusion barrier. The annealing at low temperature of $450^{\circ}C$ brought about almost no granulation of the catalyst layer, and the CNT growth was not affected by a period of annealing time. A study of changing the flow rate of $C_{2}H_{2}$ and $H_2$ showed that as the ratio of the $C_{2}H_{2}$ flow rate to the $H_2$ flow rate was lowered, the CNTs were grown to be longer With further decreasing the flow ratio, the length of CNTs reached the maximum and then became shorter. Under the optimized gas flow rates, we successfully synthesized CNTs with a uniform length over a 4-inch Si wafer at $450^{\circ}C$.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.84-84
• /
• 2012

소자가 고집적화 됨에 따라, 비저항이 낮고 electro migration (EM), Stress Migration (SM) 특성이 우수한 구리(Cu)를 배선재료로서 사용하고 있다. 그러나, 구리는 Si과 $SiO_2$의 내부로 확산이 빠르게 일어나, Si 소자 내부에 deep donor level을 형성하고, 누설 전류를 증가시키는 등 소자의 성능을 저하시킬 수 있는 문제점을 가지고 있다. 그러나, electroplating 을 이용하여 증착한 Cu 박막은 일반적으로 확산 방지막으로 쓰이는 TiN, TaN, 등의 물질과의 접착 (adhesion) 특성이 나쁘다. 따라서, Cu CMP 에서 증착된 Cu 박막의 벗겨지거나(peeling), EM or SM 저항성 저하 등의 배선에서의 reliability 문제를 야기하게된다. 따라서 Cu 와 접착 특성이 좋은 새로운 확산방지막 또는 adhesion layer의 필요성이 대두되고 있다. 본 연구에서는 이러한 Cu 배선에서의 접착성 문제를 해결하고자 Metal organic chemical vapor deposition (MOCVD)을 이용하여 제조한 코발트(Co) 박막을 $Cu/TaN_x$ 사이의 접착력 개선을 위한 adhesion layer로 적용하려는 시도를 하였다. Co는 비저항이 낮고, Cu 와 adhesion이 좋으며, Cu direct electroplating 이 가능하다는 장점을 가지고 있다. 하지만, 수소 분위기에서 $C_{12}H_{10}O_6(Co)_2$ (dicobalt hexacarbonyl tert-butylacetylene, CCTBA) 전구체에 의한 MOCVD Co 박막의 경우 탄소, 산소와 같은 불순물이 다량 함유되어 있어, 비저항, surface roughness 가 높아지게 된다. 따라서 구리 전착 초기에 구리의 핵 생성(nucleation)을 저해하고 핵 생성 후에도 응집(agglomeration)이 발생하여 연속적이고 얇은 구리막 형성을 방해한다. 이를 해결하기 위해, MOCVD Co 박막 증착 시 수소 반응 가스에 암모니아를 추가로 주입하여, 수소/암모니아의 분압을 1:1, 1:6, 1:10으로 변화시켜 $Co/TaN_x$ 박막의 특성을 비교 분석하였다. 각각의 수소/암모니아 분압에 따른 $Co/TaN_x$ 박막을 TEM (Transmission electron microscopy), XRD (X-ray diffraction), AES (Auger electron spectroscopy)를 통해 물성 및 조성을 분석하였고, AFM (Atomic force microscopy)를 이용하여, surface roughness를 측정하였다. 실험 결과, $Co/TaN_x$ 박막은 수소/암모니아 분압 1:6에서 90 ${\mu}{\Omega}-cm$의 낮은 비저항과 0.97 nm 의 낮은 surface roughness 를 가졌다. 뿐만 아니라, MOCVD 에 의해 증착된 Co 박막이4-6 % concentration 의 탄소 및 산소 함량을 가지는 것으로 나타났고, 24nm 크기의 trench 기판 위에 약 6nm의 $Co/TaN_x$ 박막이 매우 균일하게 형성된 것을 확인 할 수 있었다. 이러한 결과들은, 향후 $Co/TaN_x$ 박막이 Cu direct electroplating 공정이 가능한 diffusion barrier로서 성공적으로 사용될 수 있음을 보여준다.