Transactions on Electrical and Electronic Materials
/
v.11
no.4
/
pp.182-185
/
2010
$Pb_{0.99}[(Zr_{0.6}Sn_{0.4})_{0.9}Ti_{0.1}]_{0.98}Nb_{0.02}O_3$ (PNZST) thin films were deposited by radio frequency magnetron sputtering on a $(La_{0.5}Sr_{0.5})CoO_3$ (LSCO)/Pt/Ti/$SiO_2$/Si substrate using a PNZST target with an excess PbO of 10 mole%. The thin films deposited at the substrate temperature of $500^{\circ}C$ crystallized to a perovskite phase after rapid thermal annealing (RTA). The thin films, which annealed at $650^{\circ}C$ for 10 seconds in air, exhibited good crystal structures and ferroelectric properties. The remanent polarization and coercive field of the fabricated PNZST capacitor were approximately $20uC/cm^2$ and 50 kV/cm, respectively. The reduction of the polarization after $2.2\;{\times}\;10^9$ switching cycles was less than 10%.
Park, Si-Jun;Seo, Seong-Moon;Yoo, Young-Soo;Jeong, Hi-Won;Jang, HeeJin
Corrosion Science and Technology
/
v.15
no.3
/
pp.129-134
/
2016
The effects of Ti on the high temperature oxidation of Ni-based superalloys were investigated by cyclic oxidation at $850^{\circ}C$ and $1000^{\circ}C$. The oxide scale formed at $850^{\circ}C$ consists of $Cr_2O_3$, $Al_2O_3$, and $NiCr_2O_4$ layers, while a continuous $Al_2O_3$ layer was formed at $1000^{\circ}C$. The oxidation rate of the alloy with higher Ti content was higher than the alloy with less Ti content at $850^{\circ}C$, possibly due to the increase in the metal vacancy concentration in the $Cr_2O_3$ layer involved by incorporation of $Ti^{4+}$. However, Ti improved the oxidation resistance of the superalloy at $1000^{\circ}C$ by reducing oxygen vacancy concentration in $Al_2O_3$ layer.
Journal of the Korean institute of surface engineering
/
v.38
no.3
/
pp.106-111
/
2005
Ternary Ti-B-C coatings were synthesized on WC-Co and Si wafers substrates by a PECVD technique using a gaseous mixture of $TiCl_4,\;BCl_3,\;CH_4,\;Ar,\;and\; H_2$. The effects of deposition variables such as substrate temperature, gas ratio, $R_x=[BCl_3/(CH_4+BCl_3)]$ on the microstructure and mechanical properties of Ti-B-C coatings were investigated. From our instrumental analyses, the synthesized Ti-B-C coatings was confirmed to be composites consisting of nanocrystallites TiC, quasi-amorphous TiB2, and amorphous carbon at low boron content, on the contrary, nanocrystallites $TiB_2$, quasi-amorphous TiC, and amorphous carbon at relatively high boron content. The microhardness of the Ti-B-C coatings increased from $\~23 GPa$ of TiC to $\~38 GPa$ of $Ti_{0.33}B_{0.55}C_{0.11}$ coatings with increasing the boron content. The $Ti_{0.33}B_{0.55}C_{0.11}$ coatings showed lower average friction coefficient of 0.45, in addition, it showed relatively better wear behavior compared to other binary coatings of $TiB_2$ and TiC. The microstruture and microhardness value of Ti-B-C coatings were largely depend on the deposition temperature.
In this study, ferroelectric $PbTiO_3$ thin films were deposited on the Pt/$SiO_2$/Si substrate by Sol-Gel method. $PbTiO_3$ stock solution was made and spin-cooled at 4000[rpm] for 30[sec.]. Coated specimens were dried at $400[^{\circ}C]$ for 10[min.] and then annealed at $500{\sim}800[^{\circ}C]$ for 1 hour. Annealing temperature were examined to optimize micro structural and dielectric properties of the films. The ferroelectric perovskite phase was observed in the file annealed at $700[^{\circ}C]$ for 1 hour. In the case of $PbTiO_3$ thin films annealed at $700[^{\circ}C]$ for hour, dielectric constant and dielectric loss showed the good value of 324, 2.0[%], respectively.
Proceedings of the Korean Vacuum Society Conference
/
2000.02a
/
pp.123-123
/
2000
선폭이 초미세화됨에 따라 게이트 전극에서의 공핍 현상 및 불순물 확산의 물제를 갖는 poly-Si 게이트를 대체할 전극 물질로 텅스텐(W)이 많이 연구되어 왔다. 반도체 소자의 배선물질로 일찍부터 사용되어온 텅스텐은 내화성 금속의 일종으로 용융점이 높고, 저항이 낮다. 그러나, 일반적으로 사용되고 있는 CVD에 의한 텅스텐의 증착은 반응가스(WF6)로부터 오는 불소(F)의 게이트 산화막내로의 확산으로 인해 MOS 소자가 크게 열화될수 있다. 본 연구에서는 W/TiN 이중 게이트 전극 구조를 갖는 MOS 캐패시터를 제작하여 전기적 특성을 살펴보았다. P-Type (100) Si위에 RTP를 이용, 85$0^{\circ}C$에서 110 의 열산화막을 성장 및 POA를 수행한 후, 반응성 스퍼터링법에 의해 상온, 6mTorr, N2/Ar=1/6 sccm, 100W 조건에서 TiN 박막을 150, 300, 500 의 3그룹으로 증착하였다. 그 위에 LPCVD 방법으로 35$0^{\circ}C$, 0.7Torr, WF6/SiH4/H2=5/5~10/500sccm 조건에서 2000~3000 의 텅스텐을 증착하였다. Photolithography 공정 및 습식 에칭을 통해 200$\mu\textrm{m}$$\times$200$\mu\textrm{m}$ 크기의 W/TiN 복층 게이트 MOSC를 제작하였다. W/TiN 복측 게이트 소자와 비교분석하기 위해 같은 조건의 산화막을 이용한 알루미늄(Al) 게이트, 텅스텐 게이트 MOSC를 제작하였다. 35$0^{\circ}C$에서 증착된 텅스텐 박막은 10~11$\Omega$/ 의 면저항을 가졌고 미소한 W(110) peak값을 나타내는 것으로 보아 비정질 상태에 가까웠다. TiN 박막의 경우 120~130$\Omega$/ 의 면저항을 가졌고 TiN (200)의 peak 값이 크게 나타난 반면, TiN(111) peak가 미소하게 나타났다. TiN 박막의 두께와 WF/SiH4의 가스비를 변화시켜가며 제작된 MOS 캐패시터를 HF 및 QS C-V, I-V 그리고 FNT를 통한 전자주입 방법을 이용하여 TiN 박막의 불소에 대한 확산 방지막 역할을 살펴 보았다. W/TiN 게이트 MOS 소자는 모두 순수 텅스텐 게이트보다 우수하였고, Al 게이트와 유사한 전기적 특성을 보여주었다. W/TiN 게이트 MOS 소자는 모두 순수 텅스텐 게이트보다 우수하였고, Al 게이트와 유사한 전기적 특성을 보여주었다. TiN 박막이 300 , 500 이고 WF6/SiH4의 가스비가 5:10인 경우 소자 특성이 우수하였으나, 5:5의 경우에는 FNT 전자주입 특성이 열화되기 시작하였다. 그리고, TiN박막의 두께가 150 으로 얇아질 경우에는 WF6/SiH4의 가스비가 5:10인 경우에서도 소자 특성이 열화되기 시작하였다. W/TiN 복층 게이트 MOS 캐패시터를 제작하여 전기적인 특성 분석결과, 순수 텅스텐 게이트 소자의 큰 저전계 누설 전류 특성을 해결할 수 있었으며, 불소확산에 영향을 주는 조건이 WF6/SiH4의 가스비에 크게 의존됨을 알 수 있었다. TiN 박막의 증착 공정이 최적화 될 경우, 0.1$\mu\textrm{m}$이하의 초미세소자용 게이트 전극으로서 텅스텐의 사용이 가능할 것으로 보여진다.
Journal of the Korean Crystal Growth and Crystal Technology
/
v.5
no.3
/
pp.240-249
/
1995
Rutile type of $TiO_{2}$ single crystal was grown by floating zone method in order to obtain the highly transparent and contamination-free single crystal. The linear refractive index of perpendicular and parallel to c-axis was measured as a function o f wavelength from 500 to 1000nm. The optical energy band gap was estimated as 2.99 eV from the absorption spectrum. The theoretical $\chi^{(3)}$} value of $TiO_{2}$ was discussed in comparison with that of $SiO_{2}$ quartz single crystal on the basis of semiempirical model. On the other hand, the second-hyperpolarizability, ${\gamma}({Ti}^{4+})$ was calculated in order to describe the effect of $Ti_{4}$ ion on the third order nonlinear optical properties.
Transactions of the Korean Society of Mechanical Engineers A
/
v.33
no.7
/
pp.652-657
/
2009
Strength characteristics of $Si_3N_4$ composite ceramics has been studied as functions of heat-treatment temperature and additive $SiO_2$. $SiO_2$ colloidal could significantly increase the bending strength. Crack healing temperature decreased 300 K by additive $TiO_2$. Bending strength of specimen added $SiO_2$ is higher than that of non-added $SiO_2$. Moreover, bending strength of specimen with $SiO_2$ colloidal coating is much higher that of non-coated specimen. In in-situ observation, crack-healed specimen at 1,573 K shows phenomenon like a fog on the surface. By SPM, both crack-healed specimen, non-coating and coating of $SiO_2$ colloidal, at 1,273 K were healed completely but both of 1,573 K exist crack. This was made by evaporation of $SiO_2$ at high temperature. Crack-healing materials of $Si_3N_4$ composite ceramics is crystallized $Y_2Si_2O_7$, $Y_2Ti_2O_7$ and $SiO_2$. A large amount of Si and O, and little C were detected by EPMA. Si and O increase but C decreases according to heat treatment temperature. Specimens with additive $SiO_2$ were more detected Si and O than that of non-additive $SiO_2$. Specimen with $SiO_2$ colloidal coatings were much more detected O.
The diffusion barrier property of 100-nm-thick titanium nitride (TiN) film between Cu and Si was investigated using sheet resistance measurements, etch-pit observation, x-ray diffractometry, Auger electron spectroscopy, and transmission electron microscopy. The TiN barrier fails due to the formation of crystalline defects (dislocations) and precipitates (presumably Cu-silicides) in the Si substrate which result from the predominant in-diffusion of Cu through the TiN layer. In contrast with the case of Al, it is identified that the TiN barrier fails only the in-diffusion of Cu because there is no indication of Si pits in the Si substrate. In addition, it appears that the stuffing of TiN does not improve the diffusion barrier property in the Cu/TiN/Si structure. This indicates that in the case of Al, the chemical effect that impedes the diffusion of Al by the reaction of Al with $TiO_{2}$ which is present in the grain boundaries of TIN is very improtant. On the while, in the case of Cu, there is no chemical effect because Cu oxides, such as $Cu_{2}O$ or CuO, is thermodynamically unstable in comparison with $TiO_{2}$. For this reason, it is considered that the effect of stuffing of TiN on the diffusion barrier property is not significant in the Cu/ TiN/Si structure.
Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
/
2002.07b
/
pp.861-864
/
2002
Ferroelectric $Bi_{4-x}Nd_xTi_3O_{12}$(BNdT) thin films with the composition(x=0.75) were prepared on pt/Ti/$SiO_2$/Si(100) substrate by metal-organic deposition. The electrical and structural characteristics of BNdT thin films were investigated to develop ferroelectric thin films for capacitor layers of FRAM. After spin coating, thin films were annealed at $650^{\circ}C$ for 1hour in oxygen atmosphere. Scanning electron micrographs showed uniform surfaces composed of rod-like grains. The $Bi_{4-x}Nd_xTi_3O_{12}$(X=0.75) thin film capacitors with a Pt top electrode showed better ferroelectric properties. At the applied voltage of 5V, the dielectric constant$(\varepsilon_r)$, dissipation factor$(tan{\delta})$, remanent polarization(2Pr) and nonvolatile swiching charge of the $Bi_{4-x}Nd_xTi_3O_{12}$(x=0.75)thin films were about 346.7, 0.095, $56{\mu}C/cm^2$ and $38{\mu}C/cm^2$ respectively. Also the capacitor did not show any significant fatigue up to $8{\times}10^{10}$ read/write switching cycles at a frequency of 1MHz.
Kim, Jae-Hwan;Kim, Yong-Il;Wi, Dang-Mun;Lee, Won-Jong
Korean Journal of Materials Research
/
v.7
no.8
/
pp.635-639
/
1997
ECR-PECVD법을 사용하여 450-49$0^{\circ}C$이하의 온도에서 Pt/SiO$_{2}$/Si기판 위에 PZT 박막을 증착하였다. 기판 온도가 46$0^{\circ}C$ 이하일 경우에는 페로브스이트 상과 제2상으로 이루어진 박막이 성장하였으며 기판온도가 47$0^{\circ}C$이상일 때에는 페로브스카이트 단일상의 PZT 박막이 성장하였다. 49$0^{\circ}C$에서 매우 얇은 페로브스카이트의 PZT 박막을 증착한 후 $650^{\circ}C$에서 1분간 raped thermal annealing(RTA) 처리한 결과 박막의 조성과 결정성에는 거의 변화가 없었으나 박막의 전하 저장 밀도는 크게 향상되었다. 이는 RTA 처리에 의한 저유전 계면층의 소멸이 주된 이유라고 판단된다. 열처리 후 두께 40-45nm의 PZT박막은 200kV/cm의 전장 하에서 $10^{-6}$$\textrm{cm}^2$이하의 누설전류값을 갖고 있었으며, 인가전압 1V에서 300fF/$\mu$$m^2$의 정전용량, 즉 SiO$_{2}$환산두께 0.12nm를 나타내었다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.