• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권7호
• /
• pp.320-326
• /
• 2003

Slotless Permanent Magnet Linear Synchronous Motor (PMLSM) has good control ability but thrust density is low. So, this paper proposes inserted core type of slotless PMLSM to improve its thrust density. Inserting the core between windings of each phase, detent force is generated by the difference of magnetic resistance in an air gap. To minimize detent force, this paper applies the neural network to inserted core type of slotless PMLSM. The, Magnetic pole ratio, the width of the inserted core and the width of the coil are selected as a design parameter to minimize detent force. In comparison with inserted core type one, thrust ripple greatly decreases by minimizing detent force and also thrust increases in this optimal model.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제2권1호
• /
• pp.16-22
• /
• 2013

This paper presents the analysis and optimization of air-core permanent magnet linear synchronous motor with overlapping concentrated windings to achieve high thrust density, high thrust per copper losses and low thrust ripple. For the motor design, we adopt equivalent magnetizing current (EMC) method to analyze the magnetic field and give analytical formulae for calculation of motor parameters such as no-load back EMF, dynamic force, thrust density and thrust per copper losses. Further, we proposed a multi-objective optimization by genetic algorithm to search for the optimum parameters. The design optimization is verified by 2-D Finite Element analysis (FEA).

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권2호
• /
• pp.69-75
• /
• 2004

In this paper, we propose the shape of extremely small thrust VCM for application of the Nanoindenter, which enables control of very small force and displacement. We performed optimization of the VCM shape using conjugated gradient method. And the purposes of optimization are the minimization of the permanent magnet size for the efficient systems, minimization of deviation of flux density from the air gap for operate on regular thrust and a linearization of thrust for a good control characteristic. The finite element method is used for characteristic analysis. The node moving method is used to redundant changes of design variables. As a result, the VCM produces a yew small force by the difference of flux density of lower part from higher one. Also, in a wide range of current (0［A］-1［A］), the VCM produces linear driving thrust by saturating the magnetic circuit path and operate on regular thrust by minimizing deviation of flux density of the air gap.

• 한국추진공학회지
• /
• 제18권6호
• /
• pp.27-33
• /
• 2014

KSLV-I 나로호 2단은 희박영역에서 킥모터 연소 종료 후 탑재된 나로과학위성과 분리한다. 위성과 분리된 나로호 2단은 킥모터 잔류추력 플룸을 고려하여 위성에 대한 오염 및 충돌 회피 기동(CCAM)을 수행한다. 이때 위성 예상 궤도는 킥모터 잔류추력의 Plume Density가 충분히 낮은 영역을 통과해야만 위성의 성능 보증 및 오염을 피할 수 있다. 이를 확인하기 위해서는 CCAM을 수행하는 나로호 2단 킥모터 잔류추력 Plume Density에 대한 정확한 예측이 필수적이다. 본 연구에서는 희박영역에서 널리 사용되는 DSMC 방법을 이용하여 고고도에서의 킥모터 노즐 내부를 해석하여 연속체방정식의 해와 비교하여 그 타당성을 검증한 후, 커플링 방법을 사용하여 계산 영역을 확장하여 킥모터 잔류추력의 Plume Density를 시뮬레이션 함으로써, 나로호 2단과 분리된 위성의 궤도가 킥모터 잔류추력의 Plume Density로부터 안전하다는 것을 확인하였다.

• 한국분무공학회지
• /
• 제23권4호
• /
• pp.159-168
• /
• 2018

Thrust throttling in a liquid rocket engine can be implemented via several ways such as high pressure drop injector, dual manifold, multiple chamber, pintle injector, and gas injection. Thrust throttling using gas injection controls thrust by usually injecting inert gas into propellant through an aerator to reduce the propellant's bulk density. In this study, the outside-in aerator was used in the propellant line to create two phase flow. Closed-type, open-type, and screw-type bi-swirl coaxial injectors were utilized for investigating throttling characteristics such as pressure drop, mixture density, and discharge coefficient according to gas-liquid mass ratio.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.769-771
• /
• 2011

KSLV-I 2단에 탑재된 위성은 KM과 충돌하지 않도록 오염 및 충돌 회피 기동(CCAM)을 수행하게 된다. 이때 위성이 KM 잔류 추력 Plume의 밀도가 충분히 낮은 영역을 통과해야만 오염을 피할 수 있으며, 이를 확인하기 위해서는 Plume 유동장의 정확한 예측이 필수적이다. 본 논문에서는 다양한 희박기체 유동해석에 사용되어 그 정확도가 검증된 DSMC 기법을 사용하는 러시아 ITMA 연구소의 SMILE Code를 이용하여 위성과 분리된 KM의 잔류추력에 의한 Plume의 밀도장을 시뮬레이션 하여 분포를 예측하였고, 그 결과의 신뢰성을 확인하기 위하여 KM 노즐 내부의 밀도장은 Fluent의 결과와 비교하여 그 타당성을 입증하였다.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제5B권2호
• /
• pp.137-141
• /
• 2005

A transverse flux, PM-exited linear motor (TFM-LM) with inner mover was designed and built. Its output power density is higher and its weight is lower than those of the conventional PM exited linear synchronous motors (PM LSM). To obtain the maximum thrust force under the given volume, the thrust force density with respect to the ratio of the slot width and the length of pole pitch is analyzed by the 3-dimension finite element method (FEM). Finally, calculated static thrust forces was compared with the experimental values. The calculated and measured performance of the transverse flux, PM-exited linear motor with inner mover revealed great potential for system improvements by reducing the mass of the linear motor. For examples, when this motor was applied to a ropeless elevator, it was possible to increase the power density by more than 400% over the conventional PM-LSM. The results of this study recommend this type of motor for the ropeless elevator or gearless direct linear driving system.

• Journal of Electrical Engineering and Technology
• /
• 제11권6호
• /
• pp.1700-1706
• /
• 2016

In this paper, a dual-stator, spoke-type linear vernier machine (DSSLVM) for wave energy extraction application was proposed. This machine is capable of producing a competitively high thrust force and force density at a low operation speed in direct drive systems. The operation principal and working of the proposed DSSLVM were studied. The stator core height is adjusted to improve the overall force density of the proposed machine while reducing the force ripple. To evaluate the advantages of the proposed DSSLVM, the main performance was compared with that of a recently developed linear primary permanent magnet vernier machine (LPPMVM). The proposed machine exhibited greater thrust force and force density, an improved power factor and lower force ripple with the same permanent magnet (PM) volume compared to the LPPMVM.

• 한국정밀공학회지
• /
• 제15권8호
• /
• pp.183-192
• /
• 1998

In this paper, we measure the back-EMF and the thrust of a linear brushless DC motor along the relative position between coils and magnets in various speed environments in order to obtain the back-EMF and the thrust as a function of a motor position. The measured back-EMF function and thrust function of the position differ from the analytical ones within 5%. The measured back-EMF and thrust function can, then, be employed in controlling the thrust ripple of the linear motor. Furthermore, to minimize the torque ripple of the linear motor, we suggest the design method to shape the back-EMF and thrust function of the linear motor.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 춘계전력전자학술대회 논문집(1)
• /
• pp.304-307
• /
• 2003

Usually, the thrust of a Linear Pulse Motor(LPM) is calculated by magnetic equivalent circuit modelling method. Analytical thrust deviation exists to calculating magnetic flux density by using Permeance Modelling Method, Finite Element Method, and Velocity Electric Motive Force method. For calculating accuracy thrust by using these every method, tire thrust is calculated and compared by Lorentz Force method, Magnetic coenergy Method, and Maxwell correspondence forte Method. And that becomes Important factor at the comparison of each capacity and parameter of motor. So this study wants to compare and analyze measurement data and calculating data of the static thrust of LPM. and then we can get more accuracy method, calculating the static thrust of LPM.