• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.47.1-47
• /
• 2001

The drilling process has a great importance for the production technology due to its widerspread use in the manufacturing industry. In order to enhance a maximum production rate and prevent the drill from the damage, it is important to monitor and control the drilling system. Thrust force and cutting torque are the main output variables in the design of drilling control systems. In this paper, an alternative estimation method of thrust force by using flexible neural networks is proposed. Flexible neural network uses the sigmoid activation function with adjustable parameter in order to enhance the approximation accuracy ...

• Journal of Power System Engineering
• /
• v.13 no.4
• /
• pp.62-67
• /
• 2009

In this paper we designed a prototype hybrid type linear pulse motor (HLPM) with single side stator structure for low cost. The measurement system which can get the motor characteristics of the HLPM was suggested. The static and dynamic characteristics of the thrust force are measured analyzed. And the microstep drive method is adopted and tested to the drive of prototype HLPM. The thrust waveform is measured respectively to know the differences of the thrust waveform between the microstep drive method and rectangular wave. From the experimental results, it can be confirmed that the repetitive ripple of the thrust force of the prototype HLPM is reduced by taking the microstep drive method.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.9
• /
• pp.525-531
• /
• 2004

This paper proposes inserted core type of slotless Permanent Magnet Linear Synchronous Motor(PMLSM) to improve its low thrust density. However, by inserting the core between windings of each phase, detent force is generated and it acts as thrust ripple. Furthermore, linear motors generate end effect making thrust ripple. So, this paper applies the neural network to minimize detent force and to maximize thrust. Also, sub-poles is placed at the end parts of the mover to compensate end effect. To confirm of calculation method's validity, the calculated results are compared with experimental results.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.2
• /
• pp.198-208
• /
• 1996

The plunge joints of C.V. Joint for vehicle tend to produce a cyclic axial disturbance at a frequency of three of six times shaft speed, in which this distrubance caused by internal frictional effect is related to joint angle, rotational speed, torque, and joint size. This principal axial thrust force might make vehicle shuddered when coinciding with vehicle frequency of tranverse direction, and be one of reasons to have driver feel uncomfortable, unesay, while driving vehicle. The paper makes analysis of axial thrust force & vehicle shudder through computer simulation, comparing the result with experimental data, and reviewing the effect by changing of variables such as dimensions and driving conditions.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.11
• /
• pp.505-510
• /
• 2005

On this study, we optimized maximizing the thrust force at the TFLM(Transverse Flux Linear Motor) using design of experiments by the table of orthogonal array and the analysis of means(ANOM), and classified the most contributive design factor maximizing the thrust force at the TFLM by analysis of variance(ANOVA). From now on, we are going to apply the required technique to design various uses and shapes of the TFLM.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2006.05a
• /
• pp.395-398
• /
• 2006

this paper provides a novel method to start the linear engine coupled linear generator from dead stop to its final steady state operation. This method depends mainly to use the linear generator mounted on the shaft of the linear engine to provide the required thrust force to move and oscillate the linear engine from bottom to top dead centers. It is a cost effective approach to start the internal linear combustion engine using its coupled tubular permanent magnet linear generator proposed here. This linear generator operates in this case in motoring mode, providing the required thrust force by feeding this linear generator phases with currents by using a three phase PWM inverter controlled by position feedback scheme. In order to provide the desired thrust force with specific value and direction, a position feedback is required to control the free piston engine motion through controlling the inverter switches using PWM control scheme.

• Proceedings of the KIPE Conference
• /
• 2003.07a
• /
• pp.304-307
• /
• 2003

Usually, the thrust of a Linear Pulse Motor(LPM) is calculated by magnetic equivalent circuit modelling method. Analytical thrust deviation exists to calculating magnetic flux density by using Permeance Modelling Method, Finite Element Method, and Velocity Electric Motive Force method. For calculating accuracy thrust by using these every method, tire thrust is calculated and compared by Lorentz Force method, Magnetic coenergy Method, and Maxwell correspondence forte Method. And that becomes Important factor at the comparison of each capacity and parameter of motor. So this study wants to compare and analyze measurement data and calculating data of the static thrust of LPM. and then we can get more accuracy method, calculating the static thrust of LPM.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.82-85
• /
• 2002

Due to various advantages over the conventional linear motion device such as ball-screw, linear motors have been used in wide variety of industrial applications for years. Driven by increased demand for precision machine tools, the importance of high positioning accuracy, high stiffness and high thrust are greatly increasing. In this paper, thrust ripple, detent force and thermal behavior are considered for the development of high performance linear motor whose thrust is up to 4, 000N. This paper presents a comprehensive study for an iron core type linear motor characteristics that include the influence of PM position on thrust thrust ripple by detent farce and motor dynamics as well.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.2
• /
• pp.69-75
• /
• 2004

In this paper, we propose the shape of extremely small thrust VCM for application of the Nanoindenter, which enables control of very small force and displacement. We performed optimization of the VCM shape using conjugated gradient method. And the purposes of optimization are the minimization of the permanent magnet size for the efficient systems, minimization of deviation of flux density from the air gap for operate on regular thrust and a linearization of thrust for a good control characteristic. The finite element method is used for characteristic analysis. The node moving method is used to redundant changes of design variables. As a result, the VCM produces a yew small force by the difference of flux density of lower part from higher one. Also, in a wide range of current (0［A］-1［A］), the VCM produces linear driving thrust by saturating the magnetic circuit path and operate on regular thrust by minimizing deviation of flux density of the air gap.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.10a
• /
• pp.155-160
• /
• 2001

In the use of glass fiber reinforced plastics(GFRP) it is often necessary to cut the components, but the cutting of GFRP is often made difficult by the delamination of the compositions and short tool life. Experimental investigation was conducted to evaluate the chip formation of the glass fiber reinforced plastics during orthogonal cutting. The chip formation process, cutting force, and thrust force were studied. The chip formation processes were studied through the use of quick-stop device. Chip-tool contact areas were obtained with the use of the quick-stop device, and observed using optical microscopy after polishing. Cutting force and thrust force were measured through the use of the tool dynamometer.