• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.3
• /
• pp.613-619
• /
• 2017

In this paper, DF(Dual Fuel) Generator modeling, which uses both conventional diesel fuel and LNG fuel, has been performed and monitoring system has been developed based on MATLAB/SIMULINK for the development of PMS(Power Management System) HILS(Hardware In the Loop Simulation). The principal components modeling of DF Generator are DF engine which provides the mechanical power and synchronous generator which convert the mechanical power into electrical power. Submodels, such as throttle body, intake manifold, torque generation and mass of LNG and diesel Quantity are used to perform DF engine. Also, governor is used for load sharing between paralleled DF generators to share a total load that exceeds the capacity of a single generator. To verify modeling of DF Generator designated ship lumped load Simulation is carried out. A validity of DF Generator has been verified by comparison between simulation results and estimated result from the designated lumped load.

• KIPS Transactions on Computer and Communication Systems
• /
• v.3 no.8
• /
• pp.261-270
• /
• 2014

As Internet traffic increases recently, much effort has been put on improving the performance of a web server. In addition to hardware side solutions such as replacement by high-end hardware or expansion of the number of servers, there are software side solutions to improve performance. Recent studies on these software side solutions have been actively performed. In this paper, we identify performance degradation problems occurring in a conventional TCP networking reception process and propose a way to solve them. We improve performance by combining three kinds of existing methods for Linux Networking Performance Improvement and two kinds of newly proposed methods in this paper. The three existing methods include 1) an allocation method of a packet flow to a core in a multi-core environment, 2) ITR(Interrupt Throttle Rate) method to control excessive interrupt requests, and 3) sk_buff data structure recycling. The two newly proposed methods are fd data structure recycling and epoll_event data structure recycling. Through experiments in a web server environment, we verify the effect of our two proposed methods and its combination with the three existing methods for performance improvement, respectively. We use three kinds of web servers: a simple web server, Lighttpd generally used in Linux, and Apache. In a simple web server environment, fd data structure recycling and epoll_event data structure recycling bring out performance improvement by about 7 % and 6%, respectively. If they are combined with the three existing methods, performance is improved by up to 40% in total. In a Lighttpd and an Apache web server environment, the combination of five methods brings out performance improvement by up to 36% and 20% in total, respectively.

• Journal of Mechanical Science and Technology
• /
• v.20 no.1
• /
• pp.29-41
• /
• 2006

Nowadays, with the advancement of computers, computer simulation linked with VR (Virtual Reality) technology has become a useful method for designing the automotive driving system. In this paper, the VR simulation system was developed to investigate the driving performances of the ASV (Advanced Safety Vehicle) equipped with an ACC (Adaptive Cruise Control) system. For this purpose, VR environment which generates visual and sound information of the vehicle, road, facilities, and terrain was organized for the realistic driving situation. Mathematical models of vehicle dynamic analysis, which includes the ACC algorithm, have been constructed for computer simulation. The ACC algorithm modulates the throttle and the brake functions of vehicles to regulate their speeds so that the vehicles can keep proper spacing. Also, the real-time simulation algorithm synchronizes vehicle dynamics simulation with VR rendering. With the developed VR simulation system, several scenarios are applied to evaluate the adaptive cruise controlled vehicle for various driving situations.

• International Journal of Automotive Technology
• /
• v.7 no.4
• /
• pp.441-448
• /
• 2006

In-cylinder flows such as tumble and swirl play an important role on the engine combustion efficiencies and emission formations. The tumble flow, which is dominant in current high performance gasoline engines, is able to effect fuel consumptions and emissions under a partial load condition in addition to the volumetric efficiency under a wide open throttle condition. Therefore, it is important to optimize the tumble ratio of a gasoline engine for better fuel economy, lower emissions, and maximum volumetric efficiency. First step for optimizing a tumble ratio is to measure a tumble ratio accurately. For a tumble ratio measurement, many different methods have been developed and used such as steady flow rig, PIV, PTV, and LDV. However, it is not well known about the relations among the measured tumble ratios using different methods. The purpose of this research is to correlate the tumble ratios measured using three different methods and find out merits and demerits of each measurement method. In this research the tumble flow was measured, compared, and correlated using three different measurement methods at the same engine: steady flow rig; 2-dimensional PIV; and 3-dimensional PTV water flow rig.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.5
• /
• pp.502-509
• /
• 2010

A test facility which can simultaneously measure turbocharger operating condition variables and vibro-acoustic emission in the situations that are quite similar to real internal combustion engine operating conditions has been introduced. Using this facility, a new method sweeping from full open throttle to deep surge region along constant speed curves can be utilized instead of the stationary method that has been traditionally used to obtain turbocharger compressor maps. Data covering an extensive range of the compressor performance map have been collected and analyzed. An experimental study is performed to define a noise diagram that correlates vibro-acoustic measurements to aerothermodynamic operating conditions. An instrumentation set in the facility allows the automatic definition of the operating point on the turbine and compressor map of the turbocharger. Also, radiated sound pressure and casing vibration data corresponding to the point are obtained by a microphone in the vicinity of the compressor casing and an accelerometer on the casing. The major source(s) of noise at specific operating point on the map can be easily identified with these maps. Also, acoustic characteristics of a given turbocharger at the vicinity of the surge as well as in the surge are also defined. Finally, the possibility to define mild surge region of a turbocharger using vibro-acoustic measurements is studied.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.3
• /
• pp.234-243
• /
• 2012

In this paper, a sound quality indices for the evaluation of vehicle intake and exhaust noise were developed through a correlation analysis of objective measurement data and subjective evaluation data. At first, intake and exhaust orifice noise were measured at the wide-open throttle sweep condition. And then, acoustic transfer function between intake orifice noise and interior noise at the steady state condition was measured. Also, acoustic transfer function for exhaust system was measured as the same method. Simultaneously, subjective evaluation was carried out by the paired comparison and semantic differential method by 27 engineers. Next, the correlation analysis between the psycho-acoustic parameters derived from the measured data and the subjective evaluation was performed. The most critical factor was determined and the corresponding sound quality index for the intake and exhaust noise was obtained from the multiple factor regression method. At last, the effectiveness of the proposed index was investigated.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.10
• /
• pp.1427-1434
• /
• 2003

Turbo- or Super-charging has been used to boost engine power for Gasoline- and Diesel Engine since beginning of 20th century. So far turbo-charger has enjoyed a high reputation in the charging field for its technical advantages such as no demand of operation power from engine and an excellent charging effect in a static operation at mid- and high engine speed. A mechanically driven super-charger, however, is now popular due to the high engine power at quick change of the driving mode - high engine torque even at low engine speed. Since super-charger needs operation power from engine, it is difficult to improve its relatively higher fuel consumption than that of turbo-charger. This negative point is still an obstacle to the wide use of supercharger. Super-charger using screw-type compressor will fulfill the purpose to reduce fuel consumption by minimizing operation power owing to no charge at idling or part load driving condition. This study aims to develop power control concept to achieve the minimization of operation power. A screw type super-charger was modified in design partially and installed with an internal bypass valve and a bypass tube to control charging pressure at part load. The various control concepts show a possibility to reduce operation power of super-charger.

• Journal of the Korean Society of Industry Convergence
• /
• v.20 no.4
• /
• pp.313-323
• /
• 2017

As vehicles become more intelligent this is focused on ways to enhance safety and convenience for both drivers and passengers. In particular, x-by-wire systems that replace rigid mechanical components with dynamically configurable electronic elements are being developed to expand intelligent functions, such as adaptive cruise control or lane departure warning system. Because the malfunction of safety-related modules controlling critical functions, such as brakes, throttle, and steering in x-by-wire systems, can cause injury or death, safety and reliability are the most critical issue for automotive vendors and parts manufacturers. In an effort to develop better and effective brake-by-wire system, this paper presents EMB system by using the low speed electric vehicle, which is not required large braking force, with motor controller. In addition, we design performance evaluation system of EMB with 1/4 low speed electric vehicle model and suggested EMB is evaluated through the performance evaluation system.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.10
• /
• pp.104-110
• /
• 2005

In this paper, unmanned vehicle system and VFF algorithm development with vehicle dynamics is the main topic as a part of Intelligent Transportation System. Unmanned vehicle system is classified by vehicle system and control system. Authors used RC servo motor for longitudinal control via throttle angle, shift lever control, and brake control. For lateral control, authors used step motor, equipped with reduction gear. Unmanned vehicle has nine ultrasonic sensors in front of the unmanned vehicle. After the microcontroller computes the distance between unmanned vehicle and obstacle, the control computer calculates the steering angle enough to avoid the obstacle.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.73-81
• /
• 2006

A commercial diesel engine was converted into a dedicated natural gas engine to reduce the exhaust emissions in a retrofit of a diesel-fueled vehicle. The cylinder head and piston were remodeled into engine parts suited for a spark ignition engine using natural gas. The remodeling of the combustion chamber changed the compression ratio from 21.5 to 10.5. A multi-point port injection(MPI) system for a dedicated natural gas engine was also adopted to increase the engine power and torque through improved volumetric efficiency, to allow a rapid engine response to changes in throttle position, and to control the precise equivalence ratio during cold-start and engine warm-up. The performance and exhaust emissions of the retrofitted natural gas engine after remodeling a diesel engine are investigated. The emissions of the retrofitted natural gas engine were low enough to satisfy the limits for a transitional low emission vehicle(TLEV) in Korea. We concluded that a diesel engine can be effectively converted into a dedicated natural gas engine without any deterioration in engine performance or exhaust emissions.