Lasers have given dentistry a new rapid, economic, and accurate technique for metal joining. Although laser welding has been recommended as an accurate technique, there are some limitations with this technique. For example, the two joining surfaces must have a tight-fitting contact, which may be difficult to achieve in some situations. The tensile samples used for this study were made from a custom-made pure titanium and type III gold alloy plates. 27 of 33 specimens were sectioned perpendicular to their long axis with a carborundum disk and water coolant. Six specimens remained and served as the control group. A group of 6 specimens was posed as butt joints in custom parallel positioning device with a feeler gauge at each of three gaps : 0.00, 0.25. and 0.50mm. All specimens were then machined to produce a uniform cross-sectional dimension, none of the specimens was subjected to any subsequent form of heat treatment. Scanning electron microscopy was performed on representative tested specimens at fractured surfaces in both the parent metal and the weld. Vickers hardness was measured at the center of the welds with a micropenetrometer using a force of 300gm for 15 seconds. Measurement was made at approximately $200{\mu}m\;and\;500{\mu}m$ deep from each surface. One-way analysis of variance (ANOVA) and Scheffe's test was calculated to detect differences between groups. The purpose of this study is to compare the strength and properties of the joint achieved at various butt Joint gaps by the laser welding of type III gold alloy and pure titanium tensile specimens in an argon atmosphere. The results of this study were as follows : 1. When indexing and welding pure titanium, there was no decrease in ultimate tensile strength as compared with the unsectioned alloys for indexing gaps of 0.00 to 0.50mm, although with increasing gap size may come increased distortion (p>0.05). 2. When indexing and welding type III gold alloy, there were significant differences in ultimate tensile strength among groups with weld gaps of 0.00mm, 0.25 and 0.50mm, and the control group. Group with butt contact without weld gap demonstrated a significant higher ultimate tensile strength than groups with weld gaps of 0.25 and 0.50mm (p<0.05). 3. When indexing and welding the different metal combination of type III gold alloy and pure titanium, there were significant differences in ultimate tensile strength between groups with weld gaps of 0.00, 0.25, and 0.50mm. However, the mechanical properties of the welded joint would become too brittle to be acceptable clinically (p<0.05). 4. The presence of large pores in the laser welded joint appears to be the most important factor in controlling the tensile strength of the weld in both pure titanium and type III gold alloy.
The present research set out to further validate the results that Stromborg (1976) obtained in which a correlation (r= .22, p < .001) was found between the femininity of woman nursing students and their image of nursing. In addition the experimenter set out to elucidate any possible differences in the image of nursing according to (a) religion, (b) the motivation for choosing nursing as well as, (c) the particular area in which the students hoped to work after graduating. The research was conducted by presenting questionnaire type scales including a femininity scale and a nursing image scale, to 301 graduating students attending 4 Three-year nursing schools located within Seoul from November 21st, 1978 to November 30th. The results: 1. There was clearly no relation between femininity and the image of nursing as such (r= .01, p > .43). But upon analyzing the results along five subdimensions of the nursing image variable it was discovered that : (a) if femininity is low, the nursing student tend to view the educational preparation for becoming a nurse in a more positive light (r= -.10, p < .05), and (b) if femininity is high, the students tend to perceive their social role with a positive frame of mind (r= .15, p < .005). 2. There was a significant difference found in the image of nursing as related to the religion of the nursing students, The means ranked as follows (high scores indicate a positive image of the nursing profession). Catholic > Protestant > no religion > Buddhist 3, The difference in the nursing image according to motivation for sellecting the profession emerged as quite significant (F=6.92, p < .001). The rank of the means when the subject group is divided along the dimension of motive is as follows (ranking begins with the most positive nursing image): (a) The profession itself seemed good; (b) after marriage one can do a social type of activity; (c) significant others’advice: (d) the profession matches their high school grade record; (e) it matches the economic situation of the student; (f)no particular reason for their choice: (g) it's easy to get a nursing job after graduation. 4. The particular area of nursing one intended to go into after graduation varied significantly in terms of the image of nursing (F=3.03, p < .005). The means when ranked starting with those having the most positive image of the profession: (a) nurses helping deliveries; (b) hospital nurses: (c) nursing education; (d) school nurses: (e) government nurse supervisors: (f)public health nurses: (g) (students not going into any profession); (h) (students not going into the nursing profession but into some other area).
Jeon, Myoung-Hoon;Lee, Ju-Hwan;Yang, Jung-Min;Heo, U-Beom;Lim, Tae-Hoon;Ahn, Jung-Hee;Kim, Jin
한국HCI학회:학술대회논문집
/
2008.02b
/
pp.451-455
/
2008
Emotional design gets more and more important. However, the systematical approaches to integration of user experience elements in product design have been rarely tried. This study consists of three parts. We extracted affective words fitting to design direction based on trend analysis. Then, user experience elements were matched with affective words. Finally, a prototype system was made to guide designing affective factors in electronic products. In the present study, user experience elements were defined as color, material & finishing, and sound. Through various documents analysis and trend analysis, trend analysis experts and user experience designers extracted 31 affective keywords which could fully reflect current trend. After paired-comparison of selected keywords, 2 sensibility dimensions were obtained by multidimensional scaling. Trend affective keywords could be explained by 2 dimensions of human-centered' vs. 'techno-centered' and 'warm vs. cool'. Next, user experience elements stimuli were matched with each keyword by user direct positioning on the 2 dimensions affective map. Based on the result of the experiment, the prototype system was developed for the product designers. The results of the current study could guide designers to design emotionally satisfactory products.
To investigate the nature of the waste materials in the Nanjido Landfill, we have conducted multivariate statistical analysis of geophysical data set comprised of magnetic, gravity, LandSat TM thermal band and surface depression measurement data. Because these data sets show different responses to the depth, we have transformed the observed total field magnetic data and gravity data to the residual reduced-to-pole(RTP) magnetic anomalies and the three dimensional density anomalies, respectively, and utilized the informations about the upper shallow part of the landfills only in the following process. For the statistical analysis at the points of depression measurement, the magnetic, density and LandSat data values at these points are determined by interpolation process. Since the multivarite statistical analysis technique utilizes a clustering algorithm for classification of data set and we have measured the dissimilarity between objects by using Euclidean distance, standardization was applied prior to distance calculation in order to eliminate any scaling effects due to different measurement unit of each data set. The hierarchial grouping technique was used to construct the dendrogram. The optimum number of statistical groups(clusters), which are classified on the basis of geophysical and geotechnical characteristics, appeared to be six on the resulting dendrogram. The result of this study suggests that the dimension and nature of the multicomponent waste landfills can be identified by application of the multivarite statistical analysis technique to integrated geophysical data sets.
Asia-Pacific Journal of Business Venturing and Entrepreneurship
/
v.9
no.2
/
pp.23-33
/
2014
This paper aims at delivering significant implications to high-tech startups by visualizing the implementation process of leading KOSDAQ listed companies's business model. This paper founded two meaningful outcomes; first, hish-tech starts-up make a clear direction of implementing intangible business model in real business, second, targeting the role model of benchmarking business model among leading companies, by linking common feature between high-tech starts-up and leading KOSDAQ listed venutures sharing one of Key performance indexes falls on viable business model. The research results of visualizing the implementation of leading KOSDAQ listed ventures' business model shows three major implications. First, business model indicates not just simple logic of creating and delivering values, but more shows CEO leading management vehicle. Second, business model represents the multi-dimension process itself of integrating in and out company's core assets and competencies initiated by CEO. Third, financial outcomes of business model is automatic result of implementing on setting target customer, creating value, and delivering it rather than planned strategically. Fourth, the focal points of implementing business model falls on collecting real information from business sites.
We report on kyanite newly found in the Yongduri gneiss complex of the Chuncheon-Hongcheon area, central Gyeonggi massif. Major mineral assemblage of quartzofeldspathic gneisses in the study area consists of biotite+ garnet+ sillimanite + plagioclase+ quartz${\pm}$kyanite${\pm}$K-feldspar${\pm}$muscovite. Kyanite occurs in four samples, and coexists with sillimanite in three of these samples. In most cases, kyanite is anhedral to subhedral, ranges up to Imm in the maximum dimension, and occurs as metastable relict grains. These observations indicate that the Yongduri gneiss complex has experienced a medium-pressure type metamorphism, followed by low-pressure type one belonging to the sillimanite+K-feldspar zone. Average temperature and pressure of the peak metamorphism are $683{\pm}62^{\circ}C$ and 4.9-5.5 kbar, respectively, when the existing chemical data are re-interpreted. In conjunction with the finding of kyanite in the Cheongpyeong-Gapyeong area (Lee and Cho, 19921, this study demonstrates that kyanite may occur regionally in central Gyeonggi gneiss complex. Moreover, the persistence of kyanite even after the high-T metamorphism of the sillimanitetK-feldspar zone suggests that the central Gyeonggi massif has experienced a tectonometamorphic evolution characterized by a rapid uplift.
Pinus densiflora stands are common secondary forest communities on infertile soils in Korea. The stands are results of long severe past biotic pressure such as cutting, burning and grazing. These could be regarded as biotic climax in Korea. Because of their prevalent occurrence, relatively simple species and age composition, and their domestic economic importance, study of their distributional patterns may give some basic knowledge for better utilization of land resources in Korea. To detect distributional patterns and interspecific associations ten pine stands, each of which was homogenious with respect to topography and physiognomy, were subjectively selected from pine stands in Kyunggi Province near Seoul in 1969 and were made object of this study. Four contiguous systematic samples of count for trees, shrubs and seedlings from belt transects were collected from homogeneous areas within ten natural pine stands. The belt transect was 64m or 128m in length, and 1m, 2m or 4m in width. Basic units within the transect ranged from 64 to 256. The data from the contiguous transects were analysed in terms of multiple split-plot experiment. Departure from randomness of stem distribution, i.e., pattern, was tested in terms of variance mean ratio. For the detection of association between species, correlation coefficient was calculated for different block sizes. The values of ${\gamma}$ were tested by the usual t-test. Fine trees within one of the stands showed significant regular distribution through out the blocks. Within other eight stands pines were randomly distributed at basic unit with 4$\times$4m, 2$\times$2m, 2$\times$1m and 1$\times$1m. One significantly clumped distribution at basic unit 2$\times$2m, however, was observed from one of the pine stands. These randomly distributed groups were themselves significantly regularly distributed throughout the blocks for four pine stands. For the other four pine stands, in addition to the random distribution at the basie unit(the primary random group), randomly distributed groups with 32m dimension(the secondary random groups) were also observed. Both the primary and the secondary random groups were significantly regularly distributed at the rest of blocks. Pine seedlings were not distributed randomly thoughout the blocks. Within three of the ten stands they were contagiously distributed. Important shrub species underneath pines such as Querus serrata, Q. acutissima, Leapedeza intermedia, Rhododendron Yedoense var. poukhanenae, Juniperus utilis, Rhododendron mucronulatum var. ciliatum shnwed consistently similar distributional pattern with the pine at each stand. The shrub species pairs; Rhododendron Yedoense var. poukhanenae/Quercus serrata, Rhododendron mucronulatum var. ciliatum/Lespedeza intermedia were significantly negatively associated from 1m to 4m dimensional block sizes but became significantly positively associated from 8m sized blocks on. On the other hand the shrub species pairs; Lespedeza intermedia/Robinia Pseudoacacia, and Lespedeza bicolor var, japonica/Lespedeza intermedia were also significnalty negatively associated from 1m to 8m sized blocks but became significantly positively associated from 16m sized blocks on. The associational pattern between Rhododendron mucronul tun var. poukhanenae and Lespedeza intermedia was not consistent throughout the stands. In some stands negative associations were observed throughout the blocks except NS 32. From these observatons micro-edaphic variation within the pine stands seems not to be great enough to cause distributinal difference of pine trees within the ten pine stands. Among each species and pine seedings, however, the edaphic variation within the pine stands may be great enought to cause distributional variation.
Japanese larch specimens with dimension of 2.5 (radial direction) ${\times}$ 2.5 (tangential direction) ${\times}$ 2.5 cm (longitudinal direction) were prepared to determine 3 different directional internal moisture movement coefficients and surface emission coefficients along the radial-, the tangential-, and the tangential-direction. 4 sides of each cubic specimen were wrapped with paraffin tape and rubber tape, leaving open the 2 opposite surfaces of interest, to provide one dimensional moisture movement during drying. The coefficients were determined at three different temperatures, 70, 50 and $30^{\circ}C$ and at two different relative humidities, 30 and 60%. Internal moisture movement coefficients inclusive of flow of free water and diffusion of bound water and water vapor were increased in the high temperature condition. The internal moisture movement coefficient in the longitudinal direction was about six times of those in transverse directions with radial value being 20% greater than the tangential. Surface emission coefficients were increased with temperature and decreased with surface moisture content. Using this results, moisture content (MC) profile and quantities of moisture evaporating in Japanese larch lumber could be predicted in dynamic drying situations.
In todays environment in which scientific technologies are changing very fast than ever, companies have to monitor and search emerging technologies to gain competitiveness. Actually many nations try to do that. Most of them use Dephi approach based on experts review as a searching method. But experts review has been criticised for probability of inclination and its derivative problems in the sense that it is accomplished only by expert's subjectivity. To overcome such problems, we used Scientometric Method for identifying emerging technology that had been done by Delphi as a rule. We made three particular efforts in order to improve the Quality of the result. Firstly, we selected one alternative database between SCI and Scopus hoping to see evenly-distributing results in wide fields on the front burner. Secondly we used Fractional citation counting in counting citation number in the stage of linear regression analysis. Lastly, we verified Scientometric result with experts opinions to minimize probable errors in a Scientometric research. As a result, we derived 290 emerging technologies from Scientometric analysis with Scopus Database, and visualized them on 2-dimension map with data mining system named KnowledgeMatrix which was developed by KISTI.
In the 21C, each nation controls exhaust fumes from automobiles and makes an effort to develop alternative energy because of serious environmental problem. Jechon area has many historical and cultural archeological sites. And Jechon city sponsors various cultural events. But the way of transportation which is connected with Jecheon and around sightseeing places is general and not ready yet. Therefore, if a special means of vehicle is developed, it could play an another role of sightseeing resources. Special identity of Jecheon area for establishment of green vehicle traffic system which gives Jecheon area specific character was investigated for theoretical background. Traffic system was studied for establishment of direction through existent successful case study. Moreover content, method, structure and advantage & shortcoming etc. of vehicle that use green energy resource such as solar car, fuel cell car, hybrid car, natural gas car etc. were examined. The suitable means of vehicle for Jechon area was proposed to three directions with research and investigation. After comparison and investigation by inquiry of each section's experts, the most suitable traffic system of which energy resource of car, form of vehicles, the complement, dimension of vehicles etc. were decided. Design proposal should be drawn according to process of automobile design in decided direction. Special Exterior design of vehicle that use green energy resource connecting Jecheon and around area should be suggested in Jecheon City Hall and Chungchong-bukdo provincial office for vivify image of cleanliness area.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.