• 소음진동
• /
• 제5권4호
• /
• pp.515-524
• /
• 1995

Tubes in heat exchanger of fuel rods in reactor core are supported at intemediate point by support p0lates or springs. Current practice is, in case of heat exchanger, to allow clearance between tube and support plate for design and manufacturing consideration. And in case of fuel rod the clearance in support point can be generated due to the support spring force relaxation. Flow-induced vibration of a tube can cause it to impact or rub against support plate or against adjacent tubes and can result in fretting-wear. The tube-to- support dynamic interaction is used to relate experimental wear data from single-span test rigs to real multi-span heat exchanger configurations. The dynamic interaction cna be measured during experimental wear tests. However, the dynamic interaction is difficult to measure in real heat exchangers and, therefore, analytical techniques are required to estimate this interaction. This paper describels the nonlinear impact model of DAGS(Dynamic Analysis of Gapped Structure) code which simulates the tube response to external sinusodial or step excitation and predicts tube motion and tube-to-support dynamic interaction. Three experimental measurements-two single span rods excited by sinusodial force and a two span rod impacted by a steel ball are compared from the simulation nonlinear model of DAGS code. The simulation results from DAGS code are in good agreement with measurements. Therefore, the developed model of DAGS code is good analytical tool for estimating tube-to-support dynamic interaction in real heat exchangers.

• 대한건축학회논문집:구조계
• /
• 제34권6호
• /
• pp.3-10
• /
• 2018

This paper described the shear strengthening effect by deviator location in pre-damaged reinforced concrete (RC) beams strengthened with externally post-tensioning steel rods. Three reinforced concrete beams as control beam and eight post-tensioned beams using external steel rods were tested to fail in shear. The externally post-tensioning material was a steel rod of 22 mm diameter, and it had a 655 MPa yield strength and an 805 MPa tensile strength. Specimens depend on multiple variables, such as the number of deviators, location of deviator, and load pattern. The pre-damaged loads up to about 2/3 of ultimate shear capacities were applied to specimens using displacement control and the diagonal shear crack just occurred at these loading levels. And then, the post-tensioning up to when a strain of steel rod reaches about $2000{\mu}{\varepsilon}$ was continuously applied to beam. A displacement control was changed to a load control during post-tensioning. The post-tensioning resulted in increase of load-carrying capacity and restoration of existing deflection. Also, it prevented the existing diagonal cracks from excessively growing. Two deviators effectively improved the load capacity when compared with in case of test which one deviator at mid-span installed. When deviators were located near region which the diagonal crack occurred on, the strengthening impact by post-tensioning was greater.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.1299-1302
• /
• 2004

A real object duplication system (RODS), including three dimensional (3D) scanner and solid freeform fabrication system (SFFS), is a device to make three-dimensional objects directly from the drawing or photo data. A Selective Multi-Laser Sintering (SMLS) process designed in this paper is by which computer images received using 3D scanner are built up from polymer powder on building room of large size using dual laser at industrial type SFF system. Using the process can rapidly produce real object duplication components of industrial type such as cylinder, engine block, chassis of automobile, etc. In this paper, the industrial type SFF system using SMLS process is manufactured and the system is satisfied with high precision and high speed processing technique. To research characteristics of each part for theindustrial type SFF system, a structure and thermal analysis and test of each part is carried out. Also, to achievement of high performance for industrial type SFF system, design and fabrication for the structure, heater, nitrogen supply, laser and control part are carried out.

• Imaging Science in Dentistry
• /
• 제39권3호
• /
• pp.133-147
• /
• 2009

Purpose : To investigate the reproducibilities and compare the measurements in digital and MDCT-synthesized cephalometric radiograph, and to investigate the effect of head position on the measurement during imaging with MDCT. Materials and Methods : Twenty-two dry skulls (combined with mandible) were used in this study. Conventional digital cephalometric radiograph was taken in standard position, and MDCT was taken in standard position and two rotated position ($10^{\circ}$ left rotation and $10^{\circ}$ right tilting). MDCT data were imported in $OnDemand^{(R)}$ and lateral cephalometric radiograph were synthesized from 3D virtual models. Two types of rotated MDCT data were synthesized with default mode and with corrected mode using both ear rods. For all six images, sixteen angular and eleven linear measurements were made in V-$Ceph^{(R)}$ three times. Reproducibility of measurements was assessed using repeated measures ANOV A and ICC. Linear and angular measurements were compared between digital and five MDCT-synthesized images by Student t-test. Results : All measurements in six types of cephalometric radiograph were not statistically different under ICC examination. Measurements were not different between digital and MDCT-synthesized images (P>.05). Measurements in MDCT-synthesized image in $10^{\circ}$ left rotation or $10^{\circ}$ right tilting position showed possibility of difference from digital image in some measurements, and possibility of improvement via realignment of head position using both ear rods. Conclusion : MDCT-synthesized cephalometric radiograph can substitute conventional cephalometric radiograph. The error on head position during imaging with MDCT have possibility that can produce measurement errors with MDCT-synthesized image, and these position error can be corrected by realignment of the head position using both ear rods.

• Geomechanics and Engineering
• /
• 제37권4호
• /
• pp.341-358
• /
• 2024

This paper reports several plane-strain trapdoor tests conducted to investigate the effects of reinforcement on soil arching development under localized surface loading with a loading plate width three times the trapdoor width. An analogical soil composed of aluminum rods with three different diameters was used as the backfill and Kraft paper with two different stiffness values was used as the reinforcement material. Four reinforcement arrangements were investigated: (1) no reinforcement, (2) one low stiffness reinforcement R1, (3) one high stiffness reinforcement R2, and (4) two low stiffness reinforcements R1 with a backfill layer in between. The stiffness of R2 was approximately twice that of R1; therefore, two R1 had approximately the same total stiffness as one R2. Test results indicate that the use of reinforcement minimized soil arching degradation under localized surface loading. Soil arching with reinforcement degraded more at unloading stages as compared to that at loading stages. The use of stiffer reinforcement had the advantages of more effectively minimizing soil arching degradation. As compared to one high stiffness reinforcement layer, two low stiffness reinforcement layers with a backfill layer of certain thickness in between promoted soil arching under localized surface loading. Due to different states of soil arching development with and without reinforcement, an analytical multi-stage soil arching model available in the literature was selected in this study to calculate the average vertical pressures acting on the trapdoor or on the deflected reinforcement section under both the backfill self-weight and localized surface loading.

• 한국지반신소재학회논문집
• /
• 제3권4호
• /
• pp.41-48
• /
• 2004

최근 들어 기초지반 하부를 보강하는 방법으로 4층 또는 5층으로 보강재를 수평으로 배치하여 지지력을 증가시키는 공법이 연구되고 있다. 본 연구에서는 기초하부 지반을 보강함으로서 지반이 갖는 전단강도 정수를 증가시키는 방법을 검토한 것이다. 그래서 지반을 구형 또는 반원형으로 토목섬유를 사용하여 감싸는 공법을 개발하게 되었는데 이는 흡사 확대기초 밑에 또 하나의 확대기초가 존재하는 양상이 된다. 이러한 토목섬유보강 확대기초의 지지력에 대한 메카니즘을 검토하기 위해서 알루미늄봉을 이용한 모형재하시험을 실시하였다. 모형재하시험에서 제안된 토목섬유보강 확대기초를 만들어서 하중을 직접 재하함으로서 극한지지력의 증가정도를 확인하였으며, 또한 격자표시법에 의해 지반의 점들이 이동하는 방향 등을 점검하였고, B-Shutter 촬영법을 이용하여 소성파괴가 일어나는 영역을 확인하였다.

• Journal of Periodontal and Implant Science
• /
• 제29권2호
• /
• pp.433-447
• /
• 1999

The objective of this study was to evaluate the effect a chewable tablet containing sodium flouride and lauroyl sodium sulfate on removing plaque and inhibiting gingival inflammation. A randomized parallel study was designed. 100 voluteers participated in the study. There were two test groups each with 30 subject. Test group A was instructed to brush once in the morning, and to use the tablet once in the afternoon and once in the evening. Test group B was instructed to use the tablet three times a day without brushing. There were two control groups each with 20 subjects. Control group A was instructed to brush once in the morning only. Control group B was instructed not to brush all. Two weeks before the test period, the subjects received through tooth cleaning and polishing. At baseline, GI, PI, BOP, and GCF of the Ramfjord teeth were measured in all groups. Bacteria culture was done with the plaque sampled from tooth with the deepest pocket. After 5 days, clinical indices were measured and the bacterial culture was repeated. Control group B was dropped from the study after this period. All the other groups remained and the indices and the culture was repeated after 2 weeks, and 3weeks. Also whether the oral mucosa showed signs of irritation was monitored throughout the test period. Test group A showed less PI, GI, BOP, probing depth, GCF than test group B or control group A. Especially, PI and the BOP was significantly less than that of the group that was instructed to brush once a day. This implies that the added use of this tablet aids in plaque removal in people who brush just once a day. Test group A showed increase of cocci, decrease of motile rods, and decrease of spirochetes after 14-21 days. And this was significantly different from the control group A. At no time of the test period did any of the subjects show signs of irritation of the oral mucosa or adverse reactions. Following conclusions could be obtained from this study. This chewable tablet for enhanced oral hygiene could be used as an adjunct to oral hygiene in people who do not brush adequately. The use of this tablet decreased the number of subgingival bacteria, and this could be effective in plaque removal and for prevention of gingival inflammation.

• 한국안광학회지
• /
• 제21권3호
• /
• pp.227-233
• /
• 2016

목적: 본 연구는 우세안의 방향과 우세성의 강도, 우세안과 우세손 방향의 일치와 불일치 시의 동적 입체시를 비교해보았다. 방법: 평균연령 $21.06{\pm}2.21$세인 성인 130명(남자 70명, 여자60명)을 대상으로 $3.8cm{\times}3.8cm$ 직경의 가는 링을 이용한 타각적인 방법으로 우세안(dominant eye)의 방향과 강도를 측정하였고, 삼간계(three-rods test, iNT, Korea)를 이용하여 동적 입체시(dynamic stereoacuity)를 측정하였다. 결과: 우세안의 방향에 따른 동적 입체시는 우세성이 없는 중심우세안일 때 $14.97{\pm}13.80$초, 우안 $22.10{\pm}20.01$초, 좌안 $22.31{\pm}20.39$초로 눈의 우세성이 없을 때 더 좋았으나 우세안의 방향과 동적 입체시의 상관성은 매우 낮았다. 우세안의 강도를 Center, Mild, Strong로 구분하였을 때 동적 입체시는 각각 $14.97{\pm}13.80$초, $20.76{\pm}15.73$초, $24.45{\pm}25.60$초로 우세성이 강할수록 나빠지는 결과를 보였으나 우세안 좌안에서 우세성이 Strong으로 강할 때 오히려 동적 입체시가 중심우세보다도 더 좋게 나타났다. 우세안과 우세손 방향에 따른 동적 입체시는 우안과 오른손일 때 $22.63{\pm}20.54$초, 좌안과 왼손일 때 $17.36{\pm}10.13$초, 우안과 왼손일 때 $14.79{\pm}7.05$초, 좌안과 오른손일 때 $22.97{\pm}21.42$초로 나타나 상대적으로 우세손이 오른손보다 왼손인 경우가 빈도수는 낮았으나 동적 입체시는 우세손이 왼손일 때 비교적 좋게 나타났다. 결론: 우세안의 방향과 강도에 따른 동적 입체시의 상관성은 낮았으나 눈의 우세성이 없을때 14.97초, Strong 일 때 24.45초로 우세안 강도가 강할 때 동적 입체시가 나빠지는 경향을 보였다. 따라서 우세안 방향과 강도는 입체시와 같은 양안시기능과 sport vision training, 노안교정과 mono vision과 같은 시력교정 시에 양안균형 면에서 착용자에게 좀 더 편안한 처방을 하는데 고려되어야 요소로 사료된다.

• 한국터널지하공간학회 논문집
• /
• 제21권3호
• /
• pp.397-418
• /
• 2019

터널 굴착으로 인한 지반 및 인접 구조물의 거동을 이해하고 분석하는 것은 매우 중요하며, 이는 현대사회에서의 과학기술의 발전과 함께 토목공학 분야에서 폭넓게 활용되고 있다. 근거리 사진계측기법은 지반공학 분야에서 주로 쓰이고 있으며, 최근 GeoPIV 등을 이용한 계측기법의 연구가 증가하고 있는 추세이다. 본래에는 지반의 거동을 계측하여 시각화하는 방법으로 알루미늄 봉과 타겟 포인트를 이용한 VMS 프로그램이 주로 사용되어 왔다. 하지만 이러한 방법을 적용할 경우, 타겟 포인트가 손에 의해 인위적으로 설치되기 때문에 외부적인 오차가 발생할 수 있다. 또한 포인트 사이의 그리드가 넓거나 좁을 경우 희박한 데이터가 도출될 수 있는 문제점을 안고 있다. 따라서 본 연구에서는 타겟의 사용 없이 변위를 분석할 수 있는 MATLAB 기반의 No-target 프로그램을 개발하였고 수치해석과 실내 모형시험을 통해 기존의 프로그램과의 비교 및 검증에 초점을 맞추었다. 연구 내용으로는 greenfield condition, strip foundation, pile foundation 3가지 Case에 대하여 실내 모형시험을 실시하였으며, VMS 프로그램과 No-target 프로그램의 결과로부터 total displacement와 vertical displacement의 오차율을 분석하였다. 또한 유한요소 수치해석 프로그램인 PLAXIS를 통하여 실내 모형시험과의 결과와 비교 및 검증하였다.

• 전자공학회논문지SC
• /
• 제39권6호
• /
• pp.42-48
• /
• 2002

다목적 방사선 조사장치의 설계, 제작 및 성능검사에 대해 기술하였다. 세슘-137을 사용한 다목적 방사선조사장치는 생물학에서 저선량 방사선에 대한 영향연구, 혹은 TLD(Thermo Luminescent dosimeter)의 교정을 위해 사용되어진다. 본 조사장치는 방사선 동위원소를 안전한곳에 저장하고 있다가 방사선조사시에만 조사실로 180도 회전하여 설정된 시간만큼 시료에 방사선 조사가 이루어 진 후, 사용이 끝나면 다시 차폐된 저장위치로 복귀하게된다. 제어시스템은 PLC 기반으로 구축하여 저선량율 조사장치의 시제품을 제작하였으며, 또한 컴퓨터를 통해 방사선 조사장치의 제어 및 세부 동작 상태 등을 실시간 검색, 원격제어 및 관리 할 수 있는 종합 관리 프로그램을 개발하였다. 조사실 내부 구성은 시료의 종류에 따라 최대 20RPM까지 다양하게 회전하면서 균일 조사될 수 있도록 조사실 및 챔버를 설계 제작하였으며, 조사실내 넣을 수 있는 조사체 최대 용량은 4.5리터이다. 조사실내의 방사선량의 분포도는 가프크로믹 필름을 사용하여 측정한 결과 2Ci 범위내에서 세슘-137의 경우 공기중에서 0.13cGy/min이었고 일반 물질과 등가인 물에서는 0.11cGy/min로 나타났으며, 오차는 약 ${\pm}$7%의 한도내에서 균일한 분포를 보였다. 또한 실제 누설선량은 조사실 밖 표면에서 최대 0.35mR/hr이였으며 1m 떨어진곳에서는 최대 0.03mR/hr로 허용치 이내였다.