• Journal of Technologic Dentistry
• /
• v.23 no.1
• /
• pp.95-106
• /
• 2001

The purpose of this study was to show the method of three-dimensional morphometry developed recently and to compare the accuracy of three-dimensional morphometry with those of PA cephalometry, The three-dimensional morphometry analysis program and device were developed. Steel balls (1.2mm in diameter) were attached in twenty five landmarks of artificial human skull. This artificial human skull was used as experimental materials. From three-dimensional morphometry and PA cephalometry of artificial human skull. eleven linear measurements were acquired and made into asymmetry index. Right-left differences of measurements were used as asymmetry index. These measurements and asymmetry index were compared respectively with those of actual. The results were as follows: 1. Mean difference between three-dimensional morphometry and actual artificial human skull in linear measurements was $1.99{\pm}0.37mm$, and mean difference between PA cephalometry and actual was $21.12{\pm}0.45mm$. Both of all were reduced more than those of actual. 2. Mean difference between three-dimensional morphometry and actual artificial human skull in asymmetry index was $0.07{\pm}0.42$, and mean difference between PA cephalometry and actual was $3.63{\pm}0.60$. Three-dimensional morphometry was reduced while PA cephalometry was magnified more than that of actual. 3. Each eleven asymmetry index of three-dimensional morphometry was the same negative sign as those of actuals while only N-Z, ANS-J, Tr-Go, Tr-ANS asymmetry index were the same in PA cephalometry. These results suggest that the method of three-dimensional morphometry is more accurate than those of PA cephalometry in asymmetry analysis.

• Journal of Korean Society for Geospatial Information Science
• /
• v.18 no.4
• /
• pp.141-149
• /
• 2010

Three-dimensional geo-spatial information is important for the efficient use and management of the country and the three-dimensional expression and analysis of urban projects, such as urban plans devised by local governments and urban management. Thanks to the revitalization of the geo-spatial information service industry, it is now being variously used not only in public but also private areas. For the creation of high-guiltily three-dimensional geo-spatial information, emphasis should be placed on not only the quality of the source image and three-dimensional geo-spatial model but also the level of visualization, such as level of detail and texturing. However, in the case of existing three-dimensional geo-spatial information, its establishment process is complicated and its data are not updated frequently enough, as it uses ready-created digital maps. In addition, as it uses Ortho Images, the images exist Relief displacement. As a result, the visibility is low and the three-dimensional models of artificial features are simplified to reach LoD between 2 and 3, making the images look less realistic. Therefore, this paper, analyzed the quality of three-dimensional geo-spatial information created using the three-dimensional modeling technique were applied using Digital photogrammetry technique, using digital aerial photo images by an existing large-format digital camera and multi-looking camera. The analysis of the accuracy of visualization information of three-dimensional models showed that the source image alone, without other visualization information, secured the accuracy of 84% or more and that the establishment of three-dimensional spatial information carried out simultaneously with filming made it easier to gain the latest data. The analysis of the location accuracy of true Ortho images used in the work process showed that the location accuracy was better than the allowable horizontal position accuracy of 1:1,000 digital maps.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.11 s.176
• /
• pp.91-98
• /
• 2005

This study has been focused on the development of a high speed feeding type three-dimensional bending machine. It is designed for manufacture of copper pipe for heat exchangers. For the purpose of design of the machine, analysis of bending process, structural analysis and reliability evaluation of the machine by a laser interferometer are carried out. The analysis is carried out by FEM simulation using commercial softwares, DEFORM, MARC and CATIA V5. In addition, the machine has attained high accuracy and repeatability. In order to improve the accuracy of this machine, the maximum speed, positioning accuracy and repeatability of feed are measured by the laser interferometer. The final results of analysis are applied to the design of a high speed feeding type three-dimensional bending machine and the machine is successfully developed.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.8
• /
• pp.113-121
• /
• 1999

It is necessary to calibrate measurement systems to enhance its measurement accuracy. The visual sensing system that is presented in our previous work has to be calibrated, too. It is a multiple mirror system for three-dimensional measurement, which is composed of a camera and a series of mirrors. It is important to calibrate the positions and orientations of the mirrors relative to the camera because they have direct influence on the relationship between the image plane and the task space. This paper presents the calibration method for the visual sensing system. To confirm the measurement performance of the implemented system. its measurement accuracy in measuring the locations in three-dimensional space is investigated. A series of experiments for measuring the locations of the circle-shaped marks are performed. Experimental results show that the sensing system can be effectively used for three-dimensional measurement.

• Korean Journal of Remote Sensing
• /
• v.16 no.4
• /
• pp.339-345
• /
• 2000

KOMPSAT-1 was launched on 21 December, 1999 and the main mission of the satellite is the cartography to provide the imagery from a remote earth view for the production of maps of Korean territory. For this purpose, the satellite has capability to tilt the spacecraft utmost $\pm$45 degrees to acquire stereo satellite imagery in different paths. This study aims to estimate the three dimensional positioning accuracy of stereo satellite imagery from EOC(electro-optical camera), a payload of KOMPSAT-1 satellite. For this purpose, the ground control points and check points were obtained by GPS surveying. The sensor modeling and the adjustment was performed by PCI software installed in KARI (Korea Aerospace Research Institute), which contained mathematical analysis module for KOMPSAT-1 EOC. The study areas were Taejon and Nonsan, placed in the middle part of Korea. As a result of this study, we found that the RMSE(root mean square error) value of three dimensional positioning KOMPST-1 stereo imagery can be less than 1 pixel (6.6 m) if we can use about 10 GCPs(ground control points). Then, a standarrd of FGDC (Federal Geographic Data Committee) of USA was applied to the result to estimate the three dimensional positioning accuracy of KOMPSAT-1 stereo imagery.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.11 no.4
• /
• pp.151-162
• /
• 1991

This study aims to improve the positioning accuracy by analizing the accuracys of three dimensional positioning according to various data types and preprocessing levels of SPOT imagery and the acquisition method for ground control points, and to develop the three dimensional positioning algorithm and program. In this study, the optimum polynomials of exterior orientation parameters according to each preprocessing levels (level 1B; 15 variables, level 1AP, 1A; 12 variables) are determined. As a results, the accuracy of level lAP is the best in the results of analysis about the accuracy of positioning, but level 1A which is digital image data form also shows similar positioning accuracy. Also, in level 1A image which have different acquisition method for ground control points, the accuracy of three dimensional positioning is highly improved. But, in case of low accuracy of ground control points, only introduction of additional parameters does not effect to the improvement of accuracy. Therefore simultaneous adjustment including blunder detection method should be adopted.

• Journal of the Ergonomics Society of Korea
• /
• v.18 no.3
• /
• pp.127-140
• /
• 1999

In order to apply three-dimensional images to industries, the possibility of realizing three-dimensional images should be ensured and when operating a task using three-dimensional images, the intention of the observer and the result of operation should be precisely related. The aim of this paper is to investigate the task performance of a human operator during operating a robot manipulator using three-dimensional and two-dimensional image displays. From the result of this research, it was found that the accuracy of robot operation in the case of using three-dimensional displays is much higher than in the case of using two-dimensional displays and the adapting time to the operating task using three-dimensional displays is shorter than that using two-dimensional displays. From such results, we concluded that the application of three-dimensional displays, which can closely reflect real environment, to industries is desirable.

• Journal of the Ergonomics Society of Korea
• /
• v.29 no.6
• /
• pp.925-932
• /
• 2010

Most of the research on three-dimensional interaction field have showed different accuracy in terms of sensing, mode and method. Furthermore, implementation of interaction has been a lack of consistency in application field. Therefore, this study is to suggest research trends of three-dimensional interaction using meta-analysis. Searching relative keyword in database provided with 153 domestic papers and 188 international papers covering three-dimensional interaction. Analytical coding tables determined 18 domestic papers and 28 international papers for analysis. Frequency analysis was carried out on method of action, element, number, accuracy and then verified accuracy by effect size of the meta-analysis. As the results, the effect size of sensor-based was higher than vision-based, but the effect size was extracted to small as 0.02. The effect size of vision-based using hand motion was higher than sensor-based using hand motion. Therefore, implementation of three-dimensional sensor-based interaction and vision-based using hand motions more efficient. This study was significant to comprehensive analysis of three-dimensional motion recognition for interaction and suggest to application directions of three-dimensional interaction.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.24 no.1
• /
• pp.1-8
• /
• 2006

Effective three dimensional modeling becomes essential in a wide range of drawings, such as construction, machinery and design. In particular, it has been developed as the tool enabling reverse design. Three dimensional modeling requires rapidity, accuracy and tangibility. Data acquisition methods for modeling including contact type coordinate measurement machine, LASER scanner, pattern scanner and digital photogrammetry. In this study, we try to analyze modeling techniques as well as introduce three dimensional modeling using pattern scanner. In addition, this study conducts three dimensional modeling using OPTO-Top pattern scanner with distinguished accuracy and rapidity, and then compare efficiency with digital photogrammetry. And, this study attempts to form environment that enables to turn around models on web in three dimensional ways.

• Journal of computational fluids engineering
• /
• v.19 no.2
• /
• pp.58-65
• /
• 2014

The adaptive wavelet method is studied for the enhancement of computational efficiency of three-dimensional flows. For implementation of the method for three-dimensional Euler equation, wavelet decomposition process is introduced based on the previous two-dimensional adaptive wavelet method. The order of numerical accuracy of an original solver is preserved by applying modified thresholding value. In order to assess the efficiency of the proposed algorithm, the method is applied to the computation of flow field around ONERA-M6 wing in transonic regime with 4th and 6th order interpolating polynomial respectively. Through the application, it is confirmed that the three-dimensional adaptive wavelet method can reduce the computational time while conserving the numerical accuracy of an original solver.