• 대한원격탐사학회지
• /
• 제16권4호
• /
• pp.339-345
• /
• 2000

KOMPSAT-1 was launched on 21 December, 1999 and the main mission of the satellite is the cartography to provide the imagery from a remote earth view for the production of maps of Korean territory. For this purpose, the satellite has capability to tilt the spacecraft utmost $\pm$45 degrees to acquire stereo satellite imagery in different paths. This study aims to estimate the three dimensional positioning accuracy of stereo satellite imagery from EOC(electro-optical camera), a payload of KOMPSAT-1 satellite. For this purpose, the ground control points and check points were obtained by GPS surveying. The sensor modeling and the adjustment was performed by PCI software installed in KARI (Korea Aerospace Research Institute), which contained mathematical analysis module for KOMPSAT-1 EOC. The study areas were Taejon and Nonsan, placed in the middle part of Korea. As a result of this study, we found that the RMSE(root mean square error) value of three dimensional positioning KOMPST-1 stereo imagery can be less than 1 pixel (6.6 m) if we can use about 10 GCPs(ground control points). Then, a standarrd of FGDC (Federal Geographic Data Committee) of USA was applied to the result to estimate the three dimensional positioning accuracy of KOMPSAT-1 stereo imagery.

• ETRI Journal
• /
• 제39권2호
• /
• pp.264-274
• /
• 2017

Recently, mobile positioning enhancement has attracted much attention in the 3rd generation partnership project long-term evolution system. In particular, for urban canyon environments, the need for three-dimensional (3D) positioning has increased to enable the altitude of users to be measured. For several decades, several time difference of arrival (TDOA-) based 3D positioning methods have been studied; however, they are only available when at least four evolved Node Bs (eNBs) exist nearby or when all eNBs have the same height. Therefore, in this paper, we propose a new 3D positioning method that estimates the 3D coordinates of a user using three types of two-dimensional (2D) TDOAs. However, the give inaccurate results owing to the undefined axis of the 2D coordinate plane. Therefore, we propose a novel derivation of the hyperbola equation, which includes the undefined axis coordinate in the 2D hyperbola equation. Then, we propose an interaction algorithm that mutually supplies the undefined axis coordinate of users among 2D TDOAs. By performing extensive simulations, we verify that the proposed method is the only solution applicable by using three eNBs with different heights.

• 대한토목학회논문집
• /
• 제11권4호
• /
• pp.151-162
• /
• 1991

본 연구에서는 자료형태 및 전처리수준이 다른 위성영상자료를 이용하여 전처리수준에 따른 외부표정요소의 최적다항식형태와 위치결정정확도를 파악하고, 지상기준점의 획득방법 및 획득방법에 따른 3차원 위치결정정확도를 분석함으로서 SPOT 위성영상을 이용한 3차원 위치결정이론 및 프로그램을 개발하고 위치결정의 정확도를 향상시키는데 목적이 있다. 본 연구수행 결과 각 전처리수준에 대한 외부표정요소의 최적다항식형태(수준 1B; 15변수, 수준 1AP, 1A; 12변수)를 결정할 수 있었으며, 전처리수준에 따른 위치결정 정확도분석에서는 수준 1AP 위성사진의 정확도가 가장 좋았으나, 수치영상인 수준 1A도 유사한 정확도를 나타냄을 알 수 있었다. 또한, 지상기준점의 획득방법이 다른 수준 1A 수치영상의 3차원 위치결정 정확도를 분석한 결과, 지상기준점의 정확도가 양호한 경우 부가매개변수의 도입만으로 정확도 향상률이 큰 반면 지상기준점의 정확도가 저하되는 경우 부가매개변수의 도입만으로 정확도가 크게 향상되지 않아 조정체계에 과대오차소거이론이 포함된 동시조정이론을 적용함이 바람직함을 알 수 있었다.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2003년도 Proceedings of ACRS 2003 ISRS
• /
• pp.606-608
• /
• 2003

This paper investigates the accuracy of three-dimensional positioning for EROS A stereo pairs when different numbers of ground control points are employed. The major works of the proposed schemes include: (1) initialization of orientation parameters (2) preliminary orbit fitting, (3) orbit refinement using the least squares filtering technique, and (4) space intersection. The experiment includes validation of positioning accuracy for an EROS A in-track stereo pair when different number of check points are employed.

• 한국측량학회지
• /
• 제16권1호
• /
• pp.41-50
• /
• 1998

수치화된 영상에 의해서 대상물에 대한 위치정보를 취득하면 자료의 처리 및 저장, 갱신이 매우 용이하다. 위성을 이용한 위치결정체계인 GPS는 전 세계 어디에서나 3차원 좌표를 쉽게 얻을 수 있다는 장점 때문에 여러 분야에서 그 효용성이 증대하고 있다. 공간상에 존재하는 대상물에 대한 위치정보를 효율적으로 취득하기 위해서는 수치사진측량의 자동화가 이루어져야 하며 자료취득과 처리과정이 실시간적으로 수행되어야 한다. 본 연구에서는 수치사진측량공정의 자동화를 위한 프로그램을 개발하였으며, CCD 사진기와 GPS 수신기를 장착한 이동차량을 제작함으로써 이동용 위치결정체계를 구축하였다. 또한 CCD 사진기의 좌ㆍ우측 정지영상과 GPS를 이용하여 지면에 대해 수직인 20개의 대상물에 대한 3차원 위치결정을 실시하였으며, 실시간 사진측량을 위한 기초 연구로서 동영상과 GPS를 이용하여 대상물에 대한 3차원 위치결정을 수행하고 정확도를 분석하였다.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제13권1호
• /
• pp.277-290
• /
• 2019

The demand for indoor positioning is increasing day by day. However, the widely used positioning methods today cannot satisfy the requirements of the indoor environment in terms of the positioning accuracy and deployment cost. In the existing research domain, the localization algorithm based on three-dimensional space is less accurate, and its robustness is not high. Visible light communication technology (VLC) combines lighting and positioning to reduce the cost of equipment deployment and improve the positioning accuracy. Further, it has become a popular research topic for telecommunication and positioning in the indoor environment. This paper proposes a surface centroid TOA localization algorithm based on the VLC system. The algorithm uses the multiple solutions estimated by the trilateration method to form the intersecting planes of the spheres. Then, it centers the centroid of the surface area as the position of the unknown node. Simulation results show that compared with the traditional TOA positioning algorithm, the average positioning error of the surface centroid TOA algorithm is reduced by 0.3243 cm and the positioning accuracy is improved by 45%. Therefore, the proposed algorithm has better positioning accuracy than the traditional TOA positioning algorithm, and has certain application value.

• International Journal of Control, Automation, and Systems
• /
• 제4권1호
• /
• pp.1-9
• /
• 2006

This paper presents the modeling and multivariable feedback control of a novel high-precision multi-dimensional positioning stage. This integrated 6-degree-of-freedom. (DOF) motion stage is levitated by three aerostatic bearings and actuated by 3 three-phase synchronous permanent-magnet planar motors (SPMPMs). It can generate all 6-DOF motions with only a single moving part. With the DQ decomposition theory, this positioning stage is modeled as a multi-input multi-output (MIMO) electromechanical system with six inputs (currents) and six outputs (displacements). To achieve high-precision positioning capability, discrete-time integrator-augmented linear-quadratic-regulator (LQR) and reduced-order linearquadratic-Gaussian (LQG) control methodologies are applied. Digital multivariable controllers are designed and implemented on the positioning system, and experimental results are also presented in this paper to demonstrate the stage's dynamic performance.

• Journal of Positioning, Navigation, and Timing
• /
• 제7권2호
• /
• pp.61-71
• /
• 2018

Existing radio positioning systems have a drawback that the attitude of user's tag is difficult to be determined. Although forward link angle of arrival (FLAOA) technology that uses measurements of array antenna arranged in a tag among the angle of arrival (AOA) technologies can estimate attitude and positioning of tags, it cannot extend the estimated results into three-dimensional (3D) results due to complex non-linear model displayed because of the effects of 3D positioning and attitude in tags. This paper proposed a radio navigation technique that determines 3D attitude and positioning via FLAOA / time of arrival (TOA) integration. According to the order of determining attitude and positioning, two integration techniques were proposed. To analyze the performance of the proposed technique, MATLAB-based simulations were used to verify the performance. The simulation results showed that the first proposed method, TOA-FLAOA integrated technique, showed about 0.15 m of positioning error, and $2-3^{\circ}$ of attitude error performances regardless of the positioning space size whereas the second method, differenced FLAOA-TOA integrated technique, revealed a problem that a positioning error became larger as the size of the positioning space became larger.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.3247-3252
• /
• 2007

Endwall losses contribute significantly to the overall losses in modern turbomachinery, especially when aerodynamic airfoil load and pressure ratio are increased. Hence, reducing the extend and intensity of the secondary flow structures helps to enhance overall efficiency. From the large range of viable approaches, a promising combination positioning and height of endwall contouring was chosen. The objective of this study is to document the three-dimensional flow in a turbine cascade in terms of streamwise vorticity, total pressure loss distribution and static pressure distribution on the endwall and blade surface and to propose an appropriate positioning and height of the endwall contouring which show best secondary, overall loss reduction among the simulated endwall. The flow through the gas turbine were numerically analyzed using three dimensional Navier-Stroke equations with a commercial CFD code ANSYS CFX-10. The result shows that the overall loss is reduced near the flat endwall rather than contoured endwall, and the case of contoured endwall installed at 30% from leading edge with height of 25% for span showed best performance.

• Korean Journal of Geomatics
• /
• 제2권1호
• /
• pp.31-35
• /
• 2002

This paper describes an experiment for three-dimensional positioning for a pair of KOMPSAT stereostrips using the ancillary data and a single ground control point. The photogrammetric model for three-dimensional positioning was performed as follows: first, initialization of orbital and attitude parameters derived from ancillary data; second, adjustment of orbital and attitude parameters for the satellite to minimize the ground position error with respect to a GCP using the collinearity condition; third, determination of actual satellite position; and lastly, space intersection. This model was tested for a pair of stereo strips with 0.6 base-to-height ratio and GCPs identified from a 1:5,000 scale digital map. As the result, the satellite position of offset was corrected by only one GCP and the accuracy for the geometric modeling showed 38.89m RMSE.