• Journal of the Korean Wood Science and Technology
• /
• v.31 no.2
• /
• pp.16-23
• /
• 2003

The study was performed to obtain basic data for high quality timber production and efficient utilization of woods by investigating the effects of thinning on timber quality of domestic Korean pine(Pinus koraiensis Sieb. et Zucc.) planted. The results of this study were summarized as follows ; Comparing the appearance of knot per one meter on log surface, the heavy thinned trees contained less knots than non-thinned ones. And the ratio of dead knots was decreased in heavy thinned trees compared with the non-thinned ones, but the knot size was increased. The inclination angle of dead knot is larger than that of live knot. The crooked logs in heavy thinning plot appeared less than those in non-thinning plot. In heavy thinning plot, the log circle percentage of cross section and the ratio of clear lumber were increased, compared with in non-thinning one. The grade of log was the highest in heavy thinning plot.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.2
• /
• pp.69-75
• /
• 2001

This study was carried out to investigate the properties of woodceramics made from thinned logs of Cryptomeria japonica. In order to find the effect of steam injection time on the woodceramics fabricated with boards, boards were made with the non-steamed treatment and steamed treatment 1, 5, 10 min. at $250^{\circ}C$. The percentage of weight loss was proportional to the increased density of board The reducing rate of length and thickness, however, decreased with increasing density of board. The rate of weight loss, length and thickness reduction in non-steamed board were slightly higher than those of steamed board. When the resin impregnation rate increased, the bending strength and compressive strength of woodceramics had a tendency to increase. The bending strength and compressive strength of woodceramics in non-steamed board was higher than those of steamed board. But there was little difference between dimensional and strength properties of woodceramics and steam injection time of board.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.4
• /
• pp.51-60
• /
• 1997

We investigated the characteristics of air-and vacuum-drying heated by hot plates for 8~14cm-diameter logs or 6~12cm-thick pillars of Pinus koraiensis. And we evaluated the effects of longitudinal kerf and vacuum drying heated by hot plates. The vacuum drying times from green to 10.9~18.6% MC were 15 days, and these times were one-fifth compared to the air-drying times. The longitudinal kerfing had no significant, effect on drying rates during both air-drying and vacuum drying. But drying defects such as surface checks and V-shaped cracks were effectively prevented during air-drying and vacuum drying by longitudinal kerfing. The vacuum drying was more advantageous than air-drying for preventing of surface checks, end checks and V-shaped cracks, and especially, the vacuum dried pillars with longitudinal kerf were almost free from drying defects. In accelerated weathering conditions the resin did not exude for all specimens.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.4
• /
• pp.58-65
• /
• 2002

This research was carried out to develop field treatment techniques of thinned small diameter softwood logs and less utilized hardwood logs using sap displacement method. In this paper, we report the feasibility of using transpiration method and butt-end method for the treatment of three softwood species and three hardwood species with preservatives, fire-retardant chemicals, and dimensional stabilizer. Butt-end method was effective as a field treatment technique compared to transpiration method when considered the treatability, easiness of treatment, productivity of treated wood, and environmental aspects related to chemical treatment, regardless of the combination of wood species and chemicals.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.5
• /
• pp.547-556
• /
• 2019

Thinned, small larch logs have small diameters and no value-added final use, except as wood chips, pallets, or fuel wood, which are products with very low economic value; however, their mechanical strength is suitable for structural applications. In this study, small larch logs were sawed, dried, and cut into square timbers (with a $90mm{\times}90mm$ cross section) that were laterally glued to form core panels used to manufacture cross-laminated timber (CLT) wall panels. The surface and back of these core panels were covered with 12-mm-thick structural plywood panels, used as cross bands to obtain three-ply CLT wall panels. This attachment procedure was conducted in two different ways: gluing and pressing (CGCLT) or gluing and nailing (NGCLT). The size of the as-manufactured CLT panels was $1,220mm{\times}2,440mm$, the same as that of the plywood panels. The final wall panels were tested under lateral shear force in accordance with KS F 2154. As the lateral load resistance test required $2,440mm{\times}2,440mm$ specimens, two CLT wall panels had to be attached in parallel. In addition, the final CLT panels had tongued and grooved edges to allow parallel joints between adjacent pieces. For comparison, conventional light-frame timber shear walls and midply wall systems were also tested under the same conditions. Shear walls with edge nail spacing of 150 mm and 100 mm, the midply wall system, and the fabricated CGCLT and NGCLT wall panels exhibited maximum lateral resistances of 6.1 kN/m (100%), 9.7 kN/m (158%), 16.9 kN/m (274%), 29.6 kN/m (482%), and 35.8 kN/m (582%), respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.13 no.3
• /
• pp.41-48
• /
• 1985

In near future about 500,000 hectares of Japanese larch and pitch pine need thinning to improve crop-tree spacing and reasonable species composition in Korea. Although thinned trees show very little high quality wood, in fact, all the sawed products are suitable for construction and farming materials. Studies on the utilization of thinned small-diameter trees have been implemented in order to increase lumber yield and display the skeleton of farm buildings. The results obtained in this study were summarized as follows: 1. According to Korean Conifers Log Grading System, log grade 3 was 87.4 percent in Japanese larch bolts and 95.8 percent in pitch pine bolts from thinned trees. The ability to identify defects was essential for grading logs. 2. Cutting diagrams of sawing were developed for 1-sided sawing, 2-sided sawing and 3-sided sawing by small end diameter class of bolt and cutting sizes also were found to use effectively lumber with wane. 3. Lumber recovery of Pitch pine was a little higher than that of Japanese larch. The maximum lumber yields of pitch pine by sawing patterns were 87.2 percent for 1-sided sawing, 80.8 percent for 2-sided sawing an 64.1 percent for 3-sided sawing, up yield compared with 58.1 percent for 4-sided sawing. The lumber yield of 1, 2 and 3-sided sawing significantly was higher value than that of 4-sided sawing. 4. Lumber was inspected and graded. Lumber quality of diameter class 12cm was a little better than that of diameter class 8cm, but 90 percent of lumber in diameter c1ass 16cm fell into grade 3. The lumber grade was classified by Korean standard grades of confiers lumber. 5. Lumber from 1, 2 and 3-sided sawing was used to build the skeleton of a farm house ($53m^2$) and greenhouse ($60m^2$) in order to display more efficient use of small diameter trees from thinning 6. Total volume of timber for building a farm house was $8.1m^3$ of imported timber. Timber of $7m^3$, 70 percent of total volume would be substituted imported timber for domestic timber.