• Journal of the Korean Magnetics Society
• /
• v.24 no.5
• /
• pp.140-145
• /
• 2014

We analyzed the MnIr thickness dependence of torque signals measured in exchange coupled CoFe/MnIr ($t_{AF}$) bilayers. The measured torque signals were compared with calculated ones by Stoner-Wohlfarth model. The exchange coupling anisotropy $J_c$ was considered for the model calculation between ferromagnetic (F) and antiferromagnetic (AF) layers with uniaxial anisotropy constant of $K_F$ and $K_{AF}$, respectively. The rotational losses were appeared in the range of $0.5t_c$ < $t_{AF}$ < $t_c$ ($=J_c/K_{AF}$) by the unpinned AF layer. While, the unidirectional anisotropy ($J_k$) was caused by the pinned AF layer at $t_{AF}$ > $t_c$. The critical thickness of MnIr layer was $t_c$ = 3.4 nm in CoFe/MnIr bilayers. The rotational losses behavior as shown in $t_{AF}$ = 3 nm sample were explained by the random orientation of the easy axis of AF grains. The unidirectional anisotropy obtained from torque signal of $t_{AF}$ = 10 nm sample was $J_k=0.63J_c$. Thus, the unidirectional anisotropy can be enhanced up to $J_k=J_c$ by aligning the AF easy axis.

• Proceedings of the Optical Society of Korea Conference
• /
• 2005.07a
• /
• pp.28-29
• /
• 2005

본 논문에서는 MEH-PPV와 DFPP의 폴리머 물질을 이용하여 photovoltaic device가 제작되었고, 그림 1에 두 물질의 분자 구조가 보여진다. Photovoltaic cell의 전기-광학적 특성은 활성층의 폴리머 물질에 의해 결정된다. 이러한 특성을 알아보기 위해서 홉수 스펙트럼이 측정되었다. DFPP는 chloroform, chlorobenzen, THF, acetone에 잘 녹았으며, 본 논문에서는 chloroform이 용매로 사용되었다. 제작 공정은 다음과 같다. 인듐 주석 산화물 (ITO)이 증착된 유리기판은 photolithography 공정을 거친 후, 왕수(HNO$_{3}$ + HCL)로 식각됨으로서 전극의 패턴이 제작되었다. 그리고 ITO 전극 패턴 된 유리기판 위에 PEDOT (CH8000, Baytron)이 코팅된 후 Ar이 주입되는 Convection Oven을 이용하여 120$^{\circ}$C에서 2시간 동안 열처리되어 수분이 제거되었다. 활성층에는 MEH-PPV와 DFPP가 9:1과 2.33:1로 혼합된 폴리머가 사용되었고, 이것은 0.3 %w.t.가 되도록 chloroform에 넣어 5시간 동안 스핀바를 돌려서 용해되었다. 이 용액은 ITO 전극 패턴이 형성된 글라스 위에 3000 rpm으로 45 초간 스핀코팅 되었다. 이 때 얻어진 유기물 박막층은 80$^{\circ}$C의 Ar이 주입되는 convection oven에서 3시간 동안 경화되었다. 경화된 단층 유기물 박막층 위에 Li-Al이 1000 ${\AA}$의 두께로 증착되어 전극이 형성되었고, 이후 질소가 채워진 globe box에서 소자는 encapsulation되어 산소와 수분에 대한 영향으로부터 차단되었다. 상기의 공정으로 제작된 소자의 박막구조는 그림 2에서 보여진다. 그림 3은 MEH-PPV와 DFPP를 혼합했을 때의 흡수 스펙트럼이다. 최대 흡수 파장은 511 nm였다. 그리고 photovoltaic cell의 V-I 특성 결과가 그림 4와 같이 측정되었다. 측정에서는 300${\sim}$700 nm의 파장대를 갖는 태양광 모사계가 사용되었고, 셀의 면적은 10 mm$^{2}$였다. 그림 5의 I-V 특성으로부터 MEH-PPV와 DFPP가 9:1 로 혼합했을 때보다 2.33:1 로 혼합했을 때, photovoltaic device의 효율이 향상됨을 확인할 수 있다. 빛이 75 mW/cm$^{2}$ 의 세기로 조사될 때 9:1과 2.33:1로 혼합된 소자의 open circuit voltage (V$_{oc}$)는 비슷하지만, short circuit current Density (J$_{sc}$)는 각각 -1.39 ${\mu}$A/cm$^{2}$ 와 -3.72${\mu}$A/cm$^{2}$ 로 약 2.7배 정도 증가되었음을 볼 수 있다. 이러한 결과를 통해 electron acceptor인 DFPP의 비율이 높아질수록 photovoltaic cell의 conversion efficiency가 더 크게 됨을 확인할 수 있다. 그러므로 효율이 최대가 되는 두 폴리머의 혼합 비율이 최적화되는 조건을 찾는 것은 매우 중요한 연구가 될 것이다.

• Korean Journal of Optics and Photonics
• /
• v.3 no.4
• /
• pp.258-265
• /
• 1992

A low loss optical waveguide of $P_{2}O_{5}-SiO_{2}$on Si substrate is produced by using the chemical vapour deposition method of $SiO_2$ thin films used in Si technology. Propagation loss of the waveguide layer was 1.65 dB/cm as produced and reduced down to 0.1 dB/cm after heat treatment at $1100^{\circ}C$. By using laser lithography and reactive ion etching method $P_{2}O_{5}-SiO_{2}$ waveguide was produced and subsequently annealed at $1100^{\circ}C$.As a result of this annealing the shape of the waveguide core was changed from rectangular to semi-circular form, and the propagation loss was reduced as down to 0.03 dB/cm at 0.6328$\mu$m and 0.04dB/cm at 1.53$\mu$m. We think that the mechanism of the reduction in propagation loss during the heat treatment is the following: 1) The hydrogen bonding in waveguide layer, which causes absorption loss, is dissociated and diffused out. 2) The roughness of the interface and the micro-structure of the waveguide layer is removed. 3) The irregularities in the cross-sectional shape of the waveguide which was induced during the lithographic process were disappeared by flowing of the waveguide core.

• Korean Journal of Optics and Photonics
• /
• v.8 no.6
• /
• pp.445-449
• /
• 1997

The complex refractive indices of $Ge_2Se_2Te_5$ which show reversible phase change between the crystalline phase and an amorphous one depending upon the annealing process have been determined in the spectral range of 0.7-4.5 eV. The $Ge_2Se_2Te_5$ films were DC sputter deposited on the crystalline silicon substrate. The spectro-ellipsometry data of a thick film were analyzed following the modelling procedure where the quantum mechanical dispersion relation were used for the complex refractive indices of both the cryastalline phase $Ge_2Se_2Te_5$ and and amorphous phase $Ge_2Se_2Te_5$, respectively. On the other hand, with the surface micro-roughness layer whose effective thickness was determined from AFM analysis, the spectro-ellipsometry data were numerically inverted to yield the complex refractive index of $Ge_2Se_2Te_5$ at each wavelength. With these set of complex refractive indices, the reflectance spectra were calculated and those spectra obtained from the numerical inversion showed better agreement with the experimental reflection spectra for both the cryastalline phase and an amorphous phase. Finally, the thin $Ge_2Se_2Te_5$ film which has the optimum thickness of 26 nm as the medium for optical recording was also analyzed and the quantitative result of the film thickness and the surface microroughness has been reported.

• Korean Journal of Materials Research
• /
• v.3 no.5
• /
• pp.443-450
• /
• 1993

Self-alignment gatc Schottky contact structure on Si- implanted GaAs was formed by plasma enhanced chemical vapor dcposirion. Tungsten nitride thin films (ahclut 1600$\AA$) \vcre dopositcd on GaAs at $350^{\circ}C$ in order to fahricarc GaAs 1Cs and ttwn rapidly annealed at $750^{\circ}C$ to $900^{\circ}C$. Thermal charac tcristics of PECVD)-$W_{67}N_{43}$/GaAs structure were investigated by X-ray diffraction, photolumintesccnce. and optical deep level transient specrroscopy. Results revealed that $W_{67}N_{33}$ gate was more thermally sta ble with GaAs substrate than W gate and Si atoms implanted In $W_{67}N_{33}$/GaAs structure became morr active than those In W/GaAs after annealing. I-V characteristics of $W_{67}N_{33}$/GaAs diod c exhibired a nearly ideal diode behavior. The termal stability of $W_{67}N_{33}$/GaAs diode was better than that of W/GaAs diode with the post annealing at temperatures from 800 to $900^{\circ}C$ for 20s without As overpressure.

• Journal of the Korean institute of surface engineering
• /
• v.40 no.6
• /
• pp.254-257
• /
• 2007

TiN coating on tool steel has been widely used for the improvement of durability of tools. In this work, radical nitriding(RN) is carried out on SKD61 at $450^{\circ}C$ for 5 hours in the ammonia gas pressure $2.7{\times}10^3\;Pa$. The TiN coating is carried out by arc ion plating(AIP) with the process parameters: arc power 150 A, bias voltage -50V, coating time 40 minutes and nitrogen gas pressure $4{\times}10^3\;Pa$. Hardness, elastic modulus, friction coefficient and adhesion of TiN coating on substrates of both TiN/SKD61 and TiN/RN SKD61 coatings are investigated comparatively. The primary crystalline faces of TiN surface are(200) and(111) for TiN/SKD61 and TiN/RN SKD61 respectively. In addition to the primary phase, Fe phase exists in TiN/SKD61 coating, but not in TIN/RN SKD61. The hardness of TiN/RN SKD61 is about 700 Hv, 250 Hv(56%) higher than that of TiN/SKD61 at the near interface of TiN and substrates. At the TiN surface, hardness of TiN/RN SKD61 is 2,149 Hv, 71 Hv(3%) higher than that of TiN/SKD61. The elastic modulus of TiN coating is improved to 26.7 GPa(6%) by radical nitriding. The adhesion is improved by the RN coating showing no spalling. buckling and chipping on the scratch test track which are shown on the non-RN TiN/SKD61.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.477-477
• /
• 2008

For more than three decades, the gate dielectrics in CMOS devices are $SiO_2$ because of its blocking properties of current in insulated gate FET channels. As the dimensions of feature size have been scaled down (width and the thickness is reduced down to 50 urn and 2 urn or less), gate leakage current is increased and reliability of $SiO_2$ is reduced. Many metal oxides such as $TiO_2$, $Ta_2O_4$, $SrTiO_3$, $Al_2O_3$, $HfO_2$ and $ZrO_2$ have been challenged for memory devices. These materials posses relatively high dielectric constant, but $HfO_2$ and $Al_2O_3$ did not provide sufficient advantages over $SiO_2$ or $Si_3N_4$ because of reaction with Si substrate. Recently, $HfO_2$ have been attracted attention because Hf forms the most stable oxide with the highest heat of formation. In addition, Hf can reduce the native oxide layer by creating $HfO_2$. However, new gate oxide candidates must satisfy a standard CMOS process. In order to fabricate high density memories with small feature size, the plasma etch process should be developed by well understanding and optimizing plasma behaviors. Therefore, it is necessary that the etch behavior of $HfO_2$ and plasma parameters are systematically investigated as functions of process parameters including gas mixing ratio, rf power, pressure and temperature to determine the mechanism of plasma induced damage. However, there is few studies on the the etch mechanism and the surface reactions in $BCl_3$ based plasma to etch $HfO_2$ thin films. In this work, the samples of $HfO_2$ were prepared on Si wafer with using atomic layer deposition. In our previous work, the maximum etch rate of $BCl_3$/Ar were obtained 20% $BCl_3$/ 80% Ar. Over 20% $BCl_3$ addition, the etch rate of $HfO_2$ decreased. The etching rate of $HfO_2$ and selectivity of $HfO_2$ to Si were investigated with using in inductively coupled plasma etching system (ICP) and $BCl_3/Cl_2$/Ar plasma. The change of volume densities of radical and atoms were monitored with using optical emission spectroscopy analysis (OES). The variations of components of etched surfaces for $HfO_2$ was investigated with using x-ray photo electron spectroscopy (XPS). In order to investigate the accumulation of etch by products during etch process, the exposed surface of $HfO_2$ in $BCl_3/Cl_2$/Ar plasma was compared with surface of as-doped $HfO_2$ and all the surfaces of samples were examined with field emission scanning electron microscopy and atomic force microscope (AFM).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.169-169
• /
• 2008

To keep pace with scaling trends of CMOS technologies, high-k metal oxides are to be introduced. Due to their high permittivity, high-k materials can achieve the required capacitance with stacks of higher physical thickness to reduce the leakage current through the scaled gate oxide, which make it become much more promising materials to instead of $SiO_2$. As further studying on high-k, an understanding of the relation between the etch characteristics of high-k dielectric materials and plasma properties is required for the low damaged removal process to match standard processing procedure. There are some reports on the dry etching of different high-k materials in ICP and ECR plasma with various plasma parameters, such as different gas combinations ($Cl_2$, $Cl_2/BCl_3$, $Cl_2$/Ar, $SF_6$/Ar, and $CH_4/H_2$/Ar etc). Understanding of the complex behavior of particles at surfaces requires detailed knowledge of both macroscopic and microscopic processes that take place; also certain processes depend critically on temperature and gas pressure. The choice of $BCl_3$ as the chemically active gas results from the fact that it is widely used for the etching o the materials covered by the native oxides due to the effective extraction of oxygen in the form of $BCl_xO_y$ compounds. In this study, the surface reactions and the etch rate of $Al_2O_3$ films in $BCl_3/Cl_2$/Ar plasma were investigated in an inductively coupled plasma(ICP) reactor in terms of the gas mixing ratio, RF power, DC bias and chamber pressure. The variations of relative volume densities for the particles were measured with optical emission spectroscopy (OES). The surface imagination was measured by AFM and SEM. The chemical states of film was investigated using X-ray photoelectron spectroscopy (XPS), which confirmed the existence of nonvolatile etch byproducts.

• Journal of the Korean Magnetics Society
• /
• v.21 no.2
• /
• pp.56-60
• /
• 2011

Optical properties of $T_{0.2}Fe_{2.8}O_4$ (T = V, Cr, Mn) thin films derived from ferrimagnetic $Fe_3O_4$ were investigated by spectroscopic ellipsometry in the 1~8 eV photon-energy range. The difference in optical-absorption spectrum between the ternary compounds and $Fe_3O_4$ was analyzed based on preferable sites in spinel structure and iconicity of the doped V, Cr, and Mn ions. The observed absorption spectra from $Fe_3O_4$ and the ternary compounds can be interpreted as mainly due to charge-transfer transitions of Fe d electrons characterized by absorption structures with wide energy width. Also, the observed absorption structures with narrow energy width can be interpreted as due to crystal-field transitions between different d electron configurations of tetrahedral $Fe^{3+}(d^5)$ ion. The transitions were described in terms of spin-polarized electronic states of $Fe_3O_4$.

• Journal of the Microelectronics and Packaging Society
• /
• v.9 no.1
• /
• pp.9-13
• /
• 2002

Recently, Organic electroluminescent devices (OELDs) have been demonstrated the medium sized full color display with effective multi-layer thin films. In this study, the multi-layer OELDs were prepared on the patterened ITO (indium tin oxide)/glass substrates by the vacuum thermal evaporation method. The low molecule compounds such as $Alq_3$(trim-(8-hydroxyquinoline)aluminum) and CTM (carrier transfer material) as the electron transport and injection layers as well as TPD (triphenyl-diamine) and CuPc (copper phthalocyanine) as the hole transport and injection layers were used. The luminance was rapidly increased above the threshold voltage of 10 V. The luminance and emission spectrum for the OELDs samples with $A1/CTM/Alq_3$/TPD/1TO structures were found to be 430 cd/$m^2$and 512 nm at 17 V showing green color emission. In contrast, the samples with $Li-A1/Alq_3$/TPD/CuPC/1TO multi-structures showed 508 nm in emission spectrum and 650 cd/$m^2$at 17 V in the luminance. The increment of luminance may be ascribed to the improved efficiency of recombination in the region of the emission layers by the deposition of CuPc as hole injection layer and the low work function of the Li-Al electrode compared to the Al electrode.