• Journal of Satellite, Information and Communications
• /
• v.9 no.3
• /
• pp.22-26
• /
• 2014

This paper introduces homogeneous liquid crystal (LC) orientations on chemically modulated polystyrene (PS) surfaces using various ion beam (IB) exposure time. Transparent PS was replaced with conventional polyimde material. Especially, PS has higher transparent property than conventional polyimide thin film and it means PS is more suitable material for producing high brightness mobile LCD. As a non-contact process, IB bombardment process induced LC orientation in the direction parallel to the IB process. Through x-ray photoelectron spectroscopy, it was shown that the chemical compositional changes of the IB-irradiated PS surfaces were determined as a function of IB exposure time. Using this analysis, the optimal IB bombardment condition was determined at IB exposure time of up to 15 s. Moreover, thermal stability on IB-irradiated PS surfaces were carried out which showed that a relatively high IB exposure time induced a thermally stable LC alignment property. And it has a highly potential of mobile high transparent mobile LCD such as smart phone display and mobile information device.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.5
• /
• pp.142-149
• /
• 2009

This paper proposes and demonstrates novel flexible contact force sensing devices for 3-dimensional force measurement. To realize the sensor, polyimide and polydimethylsiloxane are used as a substrate, which makes it flexible. Thin-film metal strain gauges, which are incorporated into the polymer, are used for measuring the three-dimensional contact forces. The force sensor characteristics are evaluated against normal and shear load. The fabricated force sensor can measure normal loads up to 4N. The sensor output signals are saturated against load over 4N. Shear loads can be detected by different voltage drops in strain gauges. The device has no fragile structures; therefore, it can be used as a ground reaction force sensor for balance control in humanoid robots. Four force sensors are assembled and placed in the four corners of the robot's sole. By increasing bump dimensions, the force sensor can measure load up to 20N. When loads are exerted on the sole, the ground reaction force can be measured by these four sensors. The measured forces can be used in the balance control of biped locomotion system.

• Korean Journal of Metals and Materials
• /
• v.48 no.10
• /
• pp.951-956
• /
• 2010

This study examined the effect of copper and sulfuric acid concentrations on the surface morphology and physical properties of copper plated on a polyimide (PI) film. Electrochemical experiments with SEM and a four-point probe were performed to characterize the morphology and mechanical characteristics of copper electrodeposited in the composition of an electrolyte. The resistivity and peel strength were controlled using a range of electrolyte compositions. A lower resistivity and high flexibility were obtained when an electrolyte with 20 g/l of copper was used. However, a uniform surface was obtained when a high current density that exceeded $20mA/cm^2$ was applied, which was maintained at copper concentrations exceeding 40 g/l. Increasing sulfuric acid to >150 g/l decreased the peel strength and flexibility. The lowest resistivity and fine adhesion were detected at a $Cu^{2+}:H_2SO_4$ ratio of 50:100 g/l.

• Applied Chemistry for Engineering
• /
• v.30 no.2
• /
• pp.212-218
• /
• 2019

To investigate the effect of the oxyfluorination of carbon nanotubes (OF-CNTs) on electroless Ni deposition and electromagnetic interference shielding efficiency (EMI SE), CNTs were treated with a mixture of oxygen and fluorine gases and sequentially deposited with nickel. These samples were then manufactured into thin films on a polyimide film to evaluate their EMI SE. The surface chemical property of OF-CNTs was investigated by X-ray photoelectron spectroscopy. From the results of thermogravimetric and scanning electron microscopic analyses, it was found that both the amount of deposited Ni and the surface morphology changed depending on oxyfluorination. Moreover, the Ni-deposited CNTs pretreated with $O_2:F_2=1:9vol%$ exhibited the maximum EMI SE as approximately 19.4 dB at 1 GHz. These results were attributed to the formation of oxygen and fluorine functional groups on the surface of CNTs due to the oxyfluorination, and the functional groups enabled to deposit a suitable amount of Ni and improve the dispersion in the deposited solution.