• Journal of Biosystems Engineering
• /
• 제34권5호
• /
• pp.351-357
• /
• 2009

This study was conducted to verify the simulation model through the drying test, and investigate effect of factors, such as temperature of drying air, airflow rate, and velocity of the airflow, on the drying. The low temperature drying simulation model was developed based on the circulation dry simulation model presented by Keum et al. (1987), and by modifying low temperature thin layer drying model, equilibrium moisture content model, latent heat of vaporization model, and crack ratio prediction model. The heat pump and experimental dryer with a capacity of 150kg were used for the test. The RMSE between the predicted and measured value was 0.27% (drying temperature), 0.15% (crack ratio), and 2.08% (relative humidity), so the relevance of the model was verified. In addition, the effect of drying temperature, airflow rate, and velocity of the airflow on the drying was examined. The experimental results showed that the crack ratio at drying temperature of $25{\sim}40^{\circ}C$ was allowable. Moreover, at below $30^{\circ}C$, variation of the crack ratio was slight, but drying time was delayed. Given these results, the drying temperature of over $30^{\circ}C$ was effective. As the airflow rate increased, required energy dramatically increased. Whereas drying rate slowly increased, so loss of drying efficiency was caused. Considering these results, the dryer needed to be designed and adjusted to lower than $30\;m^3/min{\cdot}ton$. As velocity of the airflow increased, required drying energy increased when the velocity of the airflow was over $5\;m^3$/hr, while crack ratio and drying rate showed little variation.

• Current Photovoltaic Research
• /
• 제2권1호
• /
• pp.36-39
• /
• 2014

Formation mechanism of residual carbon layer, frequently observed in the $CuInSe_2$ (CIS) thin film prepared by direct solution coating routes, was investigated in order to find a way to eliminate it. As a model system, a methanol solution with dissolved Cu and In salts, whose viscosity was adjusted by adding ethylcellulose (EC), was chosen. It was found that a double layer, a top metal ion-derived film and bottom EC-derived layer, formed during an air drying step presumably due to different solubility between metal salts and EC in methanol. Consequently, the top metal ion-derived film acts as a barrier layer inhibiting further thermal decomposition of underlying EC, resulting a formation of bottom carbon residue layer.

• Journal of Biosystems Engineering
• /
• 제8권2호
• /
• pp.62-68
• /
• 1983

This study was to examine the drying characteristics of barley and the effect of moisture content of barley on milling performance. A barley variety, Jogang, having 35.0% of initial moisture content was used for this experiment. Thermo-hydrostatic dryer which consists of blower, condensor, heater, humidifier, drying chamber and control box, etc., was used for the drying experiment. The change in the weight of a barley sample was continuously measured by means of the ring type load cell installed inside the drying chamber. Milling test runs the samples having the predetermined moisture content were taken from each drying test run. A laboratory type barley miller was used for the milling test. The results of the study are summarized as follows: 1. The drying constants (k) applied for the thin layer drying model, (M-Me)/(Mo-Me) = $Ae^{-kt}$ were 0.155, 0.259 and 0.548, respectively, at the three levels of drying temperatures, $40^{\circ}C$, $50^{\circ}C$ and $60^{\circ}C$. The drying constants complied with the Arrhenius Equation, K = Ko exp (-C/T), were determined as $Ko=1.901455{\times}10^8$ and C = 6563. 2. The laboratory milling test indicated that the highest milled and head barley recovery was resulted from the sample which was dryed at $40^{\circ}C$. In general, the increase in the drying temperature from $40^{\circ}C$ to $60^{\circ}C$ indicated a negative effect on milling yields. 3. Also, the sample having 15% M.C. presented the highest milled and head barley recovery among the five moisture content levels (12, 15, 18,21 and 24%).

• Journal of Biosystems Engineering
• /
• 제35권6호
• /
• pp.401-407
• /
• 2010

In this study, computer simulations were conducted to assess the use of a circulating concurrent-flow dryer for rapeseed drying and to determined the effect of this drying method on the germination ratio of rapeseed after the drying process was complete. The simultaneous heat and mass transfer between air and rapeseed in a concurrent-flow dryer was examined by simulation. The drying simulation was based on several parameters with sequent time series. Equations concerning air psychrometrics, physical properties, thermal properties, equilibrium moisture content, thin layer drying of rapeseed, etc. were all combined to solve the simulation models. Based on energy and mass transfer in the concurrent-flow drying model, a simulation program for the circulating concurrent-flow rapeseed dryer was built along with a detailed description of the mathematical solution to the model. A pilot scale circulating concurrent-flow dryer(200 kg/batch) was used to verify the fitness of the simulation program. A comparison between the experimental data and the model predicted results was presented and discussed. The drying parameters and germination ratio were analyzed and the accuracy of the simulation program was evaluated. The simulation program proved to be reliable and was shown to be a convenient tool for predicting rapeseed drying and germination ratio of rapeseed in a concurrent-flow dryer.

• 한국식품영양학회지
• /
• 제35권6호
• /
• pp.426-434
• /
• 2022

In this study, the effect of osmotic drying conditions of mangoes on hot air drying was investigated. Four different osmotic agents of 60 Brix, such as S60, SM10, HF80, and SG25, were prepared. Mango slabs were osmotically dried with the agents at a ratio of 1:4 (w/w) for up to 8 hours. SG25 showed the lowest weight reduction and moisture loss during the process. As a result of hot-air drying, all samples showed a high correlation with the Page model (0.9761~0.9997), and the required drying time of all samples that were osmotically dried was reduced compared to the non-osmotically dried group. After hot-air drying, the pH value increased according to the drying temperature. The L, a, and b values and the total polyphenol content also decreased. Through this study, the possibility of osmotic drying was confirmed to increase the efficiency of hot air drying of mangoes, which is expected to contribute to the industrial use of domestic mangoes.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권10호
• /
• pp.983-988
• /
• 1997

We investigated the structural and dielectric properties of PZT(20/80)/PZT(80/20) heterolayered thin films that fabricated by the alkoxide-based Sol-Gel method. PZT(20/80)/PZT(80/20) heterolayered thin films were spin-coated on the Pt/Ti/SiO$_2$/Si substrate with PZT(20/80) film of tetragonal structure and PZT(80/20) film of rhombohedral structure by turns. Each layers were dried to remove the organic materials at 30$0^{\circ}C$ for 30min and sintered at $650^{\circ}C$ for 1hr. This procedure was repeated several times to form PZT(20/80)/PZT(80/20) heterolayered films and thickness of the film obtained by one-times of drying/sintering process was approximately 80-90nm. PZt-1, 3, 5 films with top layer of PZT(20/80) film of tetragonal structure showed fine grain structure and PZT-2, 4, 6 films with top layer of PZT(80/20) film of rhombohedral structure showed the dense grain microstructure without rosette-type. Dielectric constant and dielectric loss of the PZT-6 film were approximaterly 1385 and 3.3% respectively. Increasing the number of coatings remanent polarization was increased and coercive field was decreased and the values of the PZT-6 film were 8.13$\mu$C/cm$^2$and 12.5kV/cm respectively.

• 한국식품영양과학회지
• /
• 제44권11호
• /
• pp.1700-1707
• /
• 2015

입경과 건조 온도에 따른 수분 함량의 변화에 대한 연구를 수행하고 콩의 건조 특성을 박층 건조 모델을 적용하여 설명하였으며, Midilli-Kucuk 모델이 콩의 열풍건조를 서술하기에 가장 적합하였다($R^2$ >0.99). 입경을 달리한 S, M, L 군 모두에서 건조 온도가 증가할수록 건조 속도가 증가하였으며, 같은 건조 온도에서 입경이 증가할수록 건조 속도가 감소하였고, 초기 수분 함량(25%)으로부터 목표 수분 함량(10%)까지 건조시키기 위해 25, 35, $45^{\circ}C$ 건조에서 L군과 S군의 필요 건조 시간은 1,160분과 787분, 598분과 391분, 405분과 260분을 나타내어 건조 온도뿐 아니라 입경 역시 콩의 열풍건조를 위해 반드시 고려되어야 함을 확인하였다. 유효 수분확산도는 Fick's second law를 사용하여 평가되었다. 유효 수분확산도는 입경이 증가하고 건조 온도가 증가할수록 증가하였으며, 콩의 크기에 따른 콩의 온도 증가와 건조속도 증가에 의한 다공성 조직의 수축이 수분확산도의 차이를 유도하였음을 확인할 수 있었다. S, M, L 군의 유효 수분확산도는 각각 $0.83{\times}10^{-10}{\sim}1.51{\times}10^{-10}m^2/s$, $1.17{\times}10^{-10}{\sim}2.17{\times}10^{-10}m^2/s$, $1.53{\times}10^{-10}{\sim}2.95{\times}10^{-10}m^2/s$의 범위를 나타내었다. 이는 대부분의 식품 및 bioproduct의 수분확산도 범위 내에 속했다. 활성화 에너지($E_a$)는 건조 온도로부터 Arrhenius 식을 사용하여 평가되었다. 열풍건조에서 콩의 $E_a$는 24.73 kJ/mol의 값을 나타냈으며, 입경에 따른 유의적 차이는 없었다.

• Transactions on Electrical and Electronic Materials
• /
• 제11권5호
• /
• pp.212-215
• /
• 2010

$BiFeO_3/Pb(Zr_{0.95}Ti_{0.05})O_3$ (BFO/PZT) heterolayered thin films were fabricated by the spin coating method on a Pt/Ti/$SiO_2$/Si substrate using metal alkoxide solutions. The coating and heating procedure was repeated 6 times to form the heterolayered films. The thickness of the BFO/PZT films after one cycle of drying/sintering is about 30-40 nm. All BFO/PZT films show a void free uniform grain structure without the presence of rosette structures. It can be assumed that the crystal growth of the upper BFO layers can be influenced by the lower PZT layers. As the number of coatings increased, the dielectric constant increased, so that the value for the 6-layer film was 1360 at 1 KHz.

• 폴리머
• /
• 제36권5호
• /
• pp.599-605
• /
• 2012

기상중합으로 제조된 poly(3,4-ethylenedioxythiophene)(PEDOT) 박막을 다양한 금속 알콕사이드 졸 용액으로 후처리하여 내용제성, 내스크래치성, 연필경도와 같은 물리화학적 특성을 효과적으로 개선하였다. 기상중합으로 제조된 PEDOT 층위에 금속 알콕사이드의 졸-젤 공정으로부터 유도된 금속 산화막이 형성되어 전기적 특성의 큰 손실 없이 기계적 물성을 증대시킬 수 있었다. 금속 알콕사이드 졸은 다양한 기능기를 가지는 실리콘 및 티타늄계 알콕사이드 화합물을 사용하였다. 이 중에서 tetraethyl orthosilicate를 기반으로 한 금속 알콕사이드 졸을 사용한 경우의 PEDOT-금속산화물 복합 박막이 표면저항, 투과도 및 다양한 물리화학적 물성 관점에서 가장 우수하였다. PEDOT-금속산화물 복합 박막의 전기적, 광학적, 물리화학적 특성 관점에서의 최적화를 위하여 금속 알콕사이드 졸의 함량, 산화제 함량, 후처리 후의 건조온도에 따른 효과를 살펴보았다.

• Journal of Ginseng Research
• /
• 제14권3호
• /
• pp.437-441
• /
• 1990

The investigation of UV absorbing compounds in saponin fraction of Pnm.1. Kiairnk root was carried out by thin layer chromatography, semipreparative HVLC. l3C, 1H-NMR, mass spectrometry and chemical characteristics in searching plant for growth regulatony substances such as phenolic glycoside. Drying of fresh ginseng at 15 $^{\circ}C$ decreased not only number but also size of UV absorbing sports on TLC. One of the relatively large spots in fresh ginseng was isolated and identified as adenosine, which is subjected for growth stimulatory activity Detection of phenolic glycosides failed in dried root bolt was highly probable in fresh ginseng even with the insufficient amount of sample.