• 대한조선학회논문집
• /
• 제52권3호
• /
• pp.180-186
• /
• 2015

This study proposed a new method of preparing granular ethylene glycol/aliphatic detergent (EG/AD) model ice that has both strength and uniform thickness. Various sheets of granular model ice prepared in ice tanks are surveyed and their preparation procedures are analyzed. We not only made a new granular model ice using the EG/AD solution but also measured its thickness, strength, and density. In addition, we found that the strength of the model ice could be controlled by varying the time and air temperature in the consolidation phase. Based on the results of this study, we verified that granular EG/AD model ice can be prepared more uniformly and effectively than columnar EG/AD model ice. This study is intended to contribute to reducing the time required for the ice model test and the operation of the ice model basin.

• 대한조선학회논문집
• /
• 제48권5호
• /
• pp.457-464
• /
• 2011

This paper deal with the validation of correction method of ice strength and thickness to the sea trial condition based on the ice model test results. It is very difficult to conduct the model test corresponding to the sea trial condition exactly. In addition, the available sea trial data is not sufficient for the validation of correction method. In the present study, the model test results of Terry-Fox ice breker have been used to compare the corrected results of sea trial test by varying its thickness and strength of model ice. The HSVA and ITTC methods have been applied to the present comparisions and the required power has been also validated by using the HSVA method. There are rather good agreement between the sea trial result and model test corrected by the HSVA and ITTC method. The more comparisons are expected to be carried out in near future.

• 한국항공우주학회지
• /
• 제38권11호
• /
• pp.1094-1104
• /
• 2010

익형주위 착빙 현상과 관련한 기존 연구는 수치적으로 예측된 결빙형상과 실험 결과를 정성적으로 비교하는데 그쳐, 해석 결과의 정확도에 대한 판단과 외기 조건 변화에 따른 결빙형상의 체계적 분석에 한계가 있었다. 이에 본 논문에서는 실린더와 익형의 결빙 형상을 가용한 실험 및 타 수치해석 결과와 비교, 검증하고 정량적으로 분석하는 연구를 수행하였다. 먼저, 개발된 코드로부터 획득한 결빙형상을 얼음의 최대두께와 얼음의 진행방향, 얼음의 분포, 얼음의 면적을 기준으로 나타낸 후 이를 정량적으로 분석하였다. 정량적 분석을 통해 유사한 결빙 형상을 직관적으로 비교할 수 있었다. 개발한 수치해석 코드는 아랫면에서의 결빙 면적, 얼음의 두께를 작게 예측하였다. 이를 개선하기 위하여 보다 정밀한 유동장 계산을 통해 획득한 입자의 궤적이 요구된다.

• 한국지구과학회지
• /
• 제36권1호
• /
• pp.82-89
• /
• 2015

전지구 해양 해빙 예측시스템인 NEMO-CICE/NEMOVAR의 해빙 초기조건의 특성을 2013년 6월부터 2014년 5월까지 북극영역에 대하여 분석하였다. 이를 위하여 관측 자료와 재분석 자료를 모델의 초기조건과 비교하였다. 모델 초기조건은 관측에서 나타나는 해빙 면적과 해빙 두께의 월 변동을 잘 보이는 반면, 분석 기간 동안 관측과 재분석 자료보다 북극의 해빙 면적을 좁게, 해빙 두께를 얇게 나타내었다. 모델 초기조건의 북극 해빙 면적이 좁은 것은 해빙의 경계 지역에서 해빙 농도 초기조건이 약 20% 정도 재분석자료보다 낮기 때문이다. 또한 북극 평균 해빙 두께가 얇게 나타나는 이유는 연중 두꺼운 해빙이 유지되는 그린란드 및 북극 군도와 인접한 북극해 영역에서 모델의 초기조건이 약 60 cm 정도 얇기 때문이다.

• 한국해양공학회지
• /
• 제25권2호
• /
• pp.55-61
• /
• 2011

A field trial in an ice-covered sea is one of the most important tasks in the design of icebreaking ships and offshore structures. To correctly estimate the ice load and ice resistance of a ship's hull, it is essential to understand the material properties of sea ice during ice field trials and to use the proper experimental procedure for gathering effective ice data. The first Korean-made icebreaking research vessel, "ARAON," had her second sea ice trial in the Arctic Ocean during the summer season of 2010. This paper describes the test procedures used to obtain proper sea ice data, which provides the basic information for the ship's performance in an ice-covered sea and is used to estimate the correct ice load and ice resistance of the IBRV ARAON. The data gathered from the sea ice in the Chukchi Sea and Beaufort Sea during the Arctic voyage of the ARAON includes the temperature, density, and salinity of the sea ice, which was believed to be from two-year old ice floes. This paper analyses the gathered sea ice data in comparison with data from the first voyage of the ARAON during her Antarctic Sea ice trial.

• Structural Engineering and Mechanics
• /
• 제36권4호
• /
• pp.499-511
• /
• 2010

This paper examines the ice cover effects on the seismic response of concrete gravity dam-reservoir-foundation interaction systems subjected to a horizontal earthquake ground motion. ANSYS program is used for finite element modeling and analyzing the ice-dam-reservoir-foundation interaction system. The ice-dam-reservoir interaction system is considered by using the Lagrangian (displacementbased) fluid and solid-quadrilateral-isoparametric finite elements. The Sariyar concrete gravity dam in Turkey is selected as a numerical application. The east-west component of Erzincan earthquake, which occurred on 13 March 1992 in Erzincan, Turkey, is selected for the earthquake analysis of the dam. Dynamic analyses of the dam-reservoir-foundation interaction system are performed with and without ice cover separately. Parametric studies are done to show the effects of the variation of the length, thickness, elasticity modulus and density of the ice-cover on the seismic response of the dam. It is observed that the variations of the length, thickness, and elasticity modulus of the ice-cover influence the displacements and stresses of the coupled system considerably. Also, the variation of the density of the ice-cover cannot produce important effects on the seismic response of the dam.

• Korean Journal of Hydrosciences
• /
• 제1권
• /
• pp.61-71
• /
• 1990

The characteristics of radial thickness of ice jam at the center part of channel bends were analyzed briefly in this paper. Jam thickness in channel bends increases both toward the inner bank, and dowmstream. For this study, slope at the jam's underside was assumed to be liner with similarity of radial slope of bed in alluvial bends. Radial slope at the jam's underside in floating ice elements was estimated using the force equilibrium theory in the radial direction. The eqution which can be estimated the radial slope of ice jam was suggested using Falcon and Kennedy's bed layer theory. Experimental data, which were measured at the center part of cross-section in a single 180-degree bend, were compared to the calculated values using the suggested equtions. The result shows that the calcultated values were smaller than the measured ones. Ot is considered that the estimated value of shear stress in the radial direction may be smaller than the actual and two-layer model may be not suibable for alluvial bend flow.

• 한국해양공학회지
• /
• 제33권2호
• /
• pp.161-167
• /
• 2019

This paper focuses on a newly designed ice load formula based on the ARAON's 2016 Arctic field data in order to improve a structural design against ice loads. The strain gage signals from ARAON's hull plating were converted to the local ice pressure upon the hull plating using the influence coefficient matrix and finite element analysis. First, a traditional pressure-area relationship is derived by applying probabilistic approaches to handle the strains measured onboard the ARAON. Then, the local ice load prediction formula is re-analyzed after reviewing the ARAON's additional field data to consider information about the ship speed and thickness of the sea ice. It is shown that the newly developed pressure-area relationship well reflects the influence of other design parameters such as the ship speed and ice thickness in the prediction of local ice loads on Arctic vessels.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제10권6호
• /
• pp.794-802
• /
• 2018

The ice resistance series charts for icebreaking ships were developed through a series of systematic model tests in the ice tank of the Korean Research Institute of Ship and Ocean Engineering (KRISO). Spencer's (1992) component-based scaling system for ship-ice model tests was applied to extend the model ship correlations. Beam to draft ratio (B/T), length to beam ratio (L/B), block coefficient ($C_B$) and stem angle (${\alpha}$) were selected as geometric parameters for hull form development. The basic hull form (S1) of twin pod type with B/T of 3.0, L/B of 6.0, $C_B$ of 0.75 and stem angle of $25^{\circ}$ was generated with a modern hull design concept. A total of 13 hulls were designed varying the geometric parameters; B/T of 2.5 and 3.5, L/B of 5.0 and 7.0, $C_B$ from 0.65 to 0.85 in intervals of 0.05, and 5 stem angles from $15^{\circ}$ to $35^{\circ}$. Ice resistance tests were first carried out with the basic hull form in level ice with suitable speed. Four more tests for $C_B$ variations from 0.65 to 0.85 were conducted and two more for beam to draft and length to beam ratios were also performed to study the effect of the geometric parameters on ice resistance. Ice resistance tests were summarized using the volumetric coefficient, $C_V$ ($={\nabla}/L^3$), instead of L/B and $C_B$ variations. Additional model tests were also carried out to account for the effect of the stem angle, ice thickness and ice strength on ice resistance. In order to develop the ice resistance series charts with a minimum number of experiments, the trends of the ice resistance obtained from the experiments were assumed to be similar for other model ship with different geometric parameters. A total of 18 sheets composed of combinations of three different beam to draft ratios and six block coefficients were developed as a parameter of $C_V$ in the low speed regions. Three correction charts were also developed for stem angles, ice thickness and ice strength respectively. The charts were applied to estimate ice resistance for existing icebreaking ships including ARAON, and the results were satisfactory with reasonable accuracy.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제10권1호
• /
• pp.60-68
• /
• 2018

A series of tests in an ice tank was carried out using a model-scale ship to investigate the ice loading process. The ship model Uikku was mounted on a rigid carriage and towed through a level ice field in the ice tank of the Marine Technology Group at Aalto University. The carriage speed and ice thickness were varied. In this paper, ice loading process was described and the corresponding ice forces on the horizontal plane were analysed. A new method is proposed to decompose different ice force components from the total ice forces measured in the model tests. This analysis method is beneficial to understanding contributions of each force component and modelling of ice loading on hulls. The analysed experimental results could be used for comparison with further numerical simulations.