• The Korean Journal of Ceramics
• /
• 제3권4호
• /
• pp.263-268
• /
• 1997

RuO$_3$ thin films were deposited on Si(100) substrate at low temperatures by hot-wall metalorganic chemical vapor deposition. Bis(cyclopentadienyl) ruthenium, Ru$(C_5H_5)_2$, was used as the precursor RuO$_2$single phase was obtained at a low deposition temperature of 25$0^{\circ}C$ and the crystallinity of RuO$_2$thin films improved with increasing deposition temperature. RuO$_2$thin films grow perpendicularly to the substrate and show the columnar structure. The grain size of RuO$_2$films drastically increases with increasing the deposition temperature. The resistivity of the 180 nm-thick RuO$_2$thin films deposited at 27$0^{\circ}C$ was 136 $\mu$$\Omega$-cm and increased with decreasing film thickness. SrBi$_2Ta_2O_4$ thin films deposited by rf magnetron sputtering on the RuO$_2$bottom electrodes showed a fatigue-free characteristics up to ~10$^10$ cycles under 5 V bipolar square pulses and the remanent polarization, 2 P$_r$ and the coercive field, 2 E, were 5.2$\mu$C/$\textrm{cm}^2$ and 76.0 kV/cm, respectively, for an applied voltage of 5 V The leakage current density was about 7.0$\times$10$^{-6}$ A/$\textrm{cm}^2$ at 150 kV/cm.

• 한국전기전자재료학회논문지
• /
• 제17권1호
• /
• pp.7-15
• /
• 2004

The ferroelectric SBT thin films as a material of capacitors for non-volatile FRAMs have some problems that its remanent polarization value is relatively low and the crystallization temperature is quite high abovc 80$0^{\circ}C$. Therefore, in this paper, SBTN solution with S $r_{0.9}$B $i_{2.1}$T $a_{1.8}$N $b_{0.2}$$O_{9}$ composition was synthesized by sol-gel method. Sr(O $C_2$ $H_{5}$)$_2$, Bi(TMHD)$_3$, Ta(O $C_2$ $H_{5}$)$_{5}$and Nb(O $C_2$ $H_{5}$)$_{5}$ were used as precursors, which were dissolved in 2-methoxyethanol. SBTN thin films with 200 nm thickness were deposited on Pt/Ti $O_2$/ $SiO_2$/Si substrates by spin-coating. UV-irradiation in a power of 200 W for 10 min and rapid thermal annealing in a 5-Torr-oxygen ambient at 76$0^{\circ}C$ for 60 sec were used to promote crystallization. The films were well crystallized and fine-grained after annealing at $650^{\circ}C$ in oxygen ambient. The electrical characteristics of 2Pr=11.94 $\mu$C/$\textrm{cm}^2$, Ps＋/Pr＋=0.54 at the applied voltage of 5 V were obtained for a 200-nm-thick SBTN films. This results show that 2Pr values of the UV irradiated and rapid thermal annealed SBTN thin films at the applied voltage of 5 V were about 57% higher than those of no additional processed SBTN thin films. thin films.lms.s.s.

• 한국진공학회지
• /
• 제8권3A호
• /
• pp.231-237
• /
• 1999

$SrBi_{22.4}Ta_2O_9$ (SBT) thin films of 70~150 nm thickness were prepared on platinized silicon substrates by Liquid Source Misted Chemical Deposition (LSMCD) process, and their microstructure, feroelectric and leakage current characteristics were investigated. By annealing at $800^{\circ}C$ for 1 hour in oxygen ambient, SBT films were fully crystallized to the Bi layered perovskite structure without preferred orientation. The grain size of the LSMCD- derived SBT films was about 100nm, and was not varied with the film thickness. $2P_r$ and $E_c$ of the SBT films increased with decreasing the film thickness, and the 70nm-thick SBT film exhibited $2P_r$ of 17.8 $\mu$C/$\textrm{cm}^2$ and $E_c$ of 74kV/cm at applied voltage of 5V. Within the film thickness range of 70~150nm, the relative dielectric permittivity of the LSMCD-derived SBT film decreased with decreasing the film thickness. Leakage current densities lower than $10^{-7}\textrm{A/cm}^2$ at 5V were observed in the SBT films thicker than 125nm.

• 한국진공학회지
• /
• 제7권3호
• /
• pp.195-200
• /
• 1998

본 연구에서는 강유전체 박막의 게이트 산화물로 사용한 $Pt/SrBi_2Ta_2O_9(SBT)/CeO_2/Si(MFS)$와 Pt/SBT/Si(MFS) 구조의 결정 구조 및 전기적 성질 의 차이를 연구하였다. XRD 및 SEM 측정 결과 SBT/$CeO_2$/Si박막은 약5nm정도의 $SiO_2$층 이 형성되었고 비교적 평탄한 계면의 미세구조를 가지는 반면, SBT/Si는 각각 약6nm와 7nm정도의 $SiO_2$층과 비정질 중간상층이 형성되었음을 알 수 있다. 즉 CeO2 박막을 완충층 으로 사용함으로써 SBT박막과 Si기판의 상호 반응을 적절히 억제할 수 있음을 확인하였다. Pt/SBT/$CeO_2/Pt/SiO_2$/와 Pt/SBT/Pt/$SiO_2$/Si구조에서 Polarization-Electric field(P-E) 특 성을 비교해 본 결과 CeO2박막의 첨가에 따라 잔류분극값은 감소하였고 항전계값은 증가하 였다. MFIS구조에서 memory window값은 항전계값과 직접적 관련이 있으므로 이러한 항 전계값의 증가는 MFIS구조에서의 memory window값이 증가할 수 있음을 나타낸다. Pt-SBT(140nm)/$CeO_2$(25nm)/Si구조에서 Capacitance-Voltage(C-V) 측정 결과로부터 동작 전압 4-6V에서 memory wondows가 1-2V정도로 나타났다. SBT박막의 두께가 증가할수록 memory window값은 증가하였는데 memory wondows가 1-2V정도로 나타났다. SBT박막의 두께가 증가할수록 memory window값은 증가하였는데 이는 SBT박막에 걸리는 전압강하가 증가하기 때문인 것으로 생각되어진다. Pt/SBT/$CeO_2$/Si의 누설전류는 10-8A/cm2정도였고 Pt/SBT/Si 구조에서는 약10-6A/cm2정도로 약간 높은 값을 나타내었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.177-180
• /
• 2002

Thickness dependence of crystallographic orientation of diol based sol-gel derived PZT(52/48) films on dielectric and piezoelectric properties was investigated The thickness of each layer by one time spinning was about 0.2 $\mu\textrm{m}$, and crack-free films was successfully deposited on 4 inches Pt/Ti/SiO$_2$/Si substrates by 0.5 mol solutions in the range from 0.2 $\mu\textrm{m}$ to 3.8 $\mu\textrm{m}$. Excellent P-E hysteresis curves were achieved without pores or any defects between interlayers. As the thickness increased , the (111) preferred orientation disappeared from 1$\mu\textrm{m}$ to 3 $\mu\textrm{m}$ region, and the orientation of films became random above 3 $\mu\textrm{m}$. Dielectric constants and longitudinal piezoelectric coefficient d$\_$33/, measured by pneumatic method were saturated around the value of about 1400 and 300 pC/N respectively above the thickness of 0.8 7m. A micromachined piezoelectric cantilever have been fabricated using 0.8 $\mu\textrm{m}$ thickness PZT (52/48) films. PZT films were prepared on Si/SiN$\_$x/SiO$_2$/Ta/Pt substrate and fabricated unimorph cantilever consist of a 0.8 fm thick PZT layer on a SiNx elastic supporting layer, which becomes vibration when ac voltage is applied to the piezoelectric layer. The dielectric constant (at 100 kHz) and remanent polarization of PZT films were 1050 and 25 ${\mu}$C/$\textrm{cm}^2$, respectively. Electromechanical characteristics of the micromachined PZT cantilever in air with 200-600 $\mu\textrm{m}$ lengths are discussed in this presentation.

• 자원환경지질
• /
• 제13권3호
• /
• pp.167-184
• /
• 1980

The granitic plutons associated with Ogcheon geosynclinal zone can be grouped into three different subzones; SE-Subzone for the migmatitic and schistose granites of the southeast margin, 101-181m.y. old; NW-Subzone for those of the northwest margin, 112-163m. y. old; and C-Subzone for those of central part of the zone, 63-183m.y. old. The intrusives in C-Subzone are further subdivided into the older, adamellite to granodiorite (148-183m.y. old) and the younger, perthitic granites (63-106m,y. old). The metallogenic distribution of South Korea suggests that, in the Ogcheon Zone, it is possible to delineate an elongated polymetallogenic province in the general orientation of the zone intimately related with the migmatite and plutonic zones mentioned. Moreover, the mineralization in the province was basically controlled by the patterns of local geology involving country rocks and related igneous bodies, that permit subdivision of the province into the following three parts: Northeast (NE) Province consists dominantly of thick Paleozoic calcareous sediments; Middle (M) Province is characterized by predominant argillaceous and partly calcareous sediments of Precambrian to Late Paleozoic age; and Southwest (SW) Province consisting mainly of volcanic and arenaceous sediments of Mesozoic age. The three different plutonic zones with three different country rock provinces above mentioned make a combination which consists of nine classes. Each class can be assumed to be characterized by specific mineralization type. In order to classify the mineralization types, the present study sampled twenty six ore deposits and mineralized areas in Ogcheon zone as shown figure 2; eight ore deposits from plutonic SE-Subzone, ten from the plutonic NE-Subzone and eight from the plutonic C-Subzone. The characteristics of the classes are as follows: NE-SE is predominant in Au-Ag vein and Sn-migmatite of katazonal occurrence; NE-C is most productive in Pb-Zn and remarkable in Fe contact deposit in mesozone and partly Pb-Zn-Cu skarn in limestone and subordinate in mesozone and partly Pb-Zn pipes; M-SE is considerable in Au-Ag vein and rare elements (Nb, Ta, etc.) of pegmatite; M-C is predominant in F-veins in epizone and Mo-W, Fe, Cu veins occur in replacement type; M-NW is productive in Fe metamorphic and skarn types, partly remarkable in Cu, Pb-Zn contact; SW-SE is barren in mineralization related to Jurassic igneous rocks; SW-C is predominant in alunite and pyrophyllite in tuffs; and SW-NW is scarece in Pb-Zn, Cu, As and Au-Ag veins.

• 한국자기학회지
• /
• 제17권3호
• /
• pp.120-123
• /
• 2007

이 연구에서는 Ta 45/Ru 9.5/IrMn 10/CoFe $3/AlO_x$/자유층/$AlO_x$/CoFe 7/IrMn 10/Ru 60(nm) 구조를 갖는 이중장벽 자기터널접합(double-barrier magnetic tunnel junction: DMTJ)를 다루었다. 자유층은 $Ni_{16}Fe_{62}Si_8B_{14}\;7nm$, $Co_{90}Fe_{10}(fcc)$ 7 nm 및 $CoFet_1$/NiFeSiB $t_2$/CoFe $t_1$으로 구성하였으며 두께 $t_1,\;t_2$는 변화시켰다. 즉 TMR비와 RA를 개선하기 위하여 부분적으로 CoFe층을 대체할 수 있는 비정질 NiFeSiB층이 혼합된 자유층 CoFe/NiFeSiB/CoFe을 갖는 DMTJ를 연구하였다. NiFeSiB($t_1=0,\;t_2=7$)만의 자유층을 갖는 DMTJ는 터널자기저항(TMR)비 28%, 면적-저항곱(RA) $86k{\Omega}{\mu}m^2$, 보자력($H_c$) 11 Oe 및 층간 결합장($H_i$) 20 Oe를 나타내었다. $t_1=1.5,\;t_2=4$인 경우의 하이브리드 DMTJ는 TMR비 30%, RA $68k{\Omega}{\mu}m^2$ 및 $H_c\;11\;Oe$를 가졌으나 $H_i$는 37 Oe로 증가하였다. 원자현미경(AFM)과 투과전자현미경(TEM)측정을 통하여 NiFeSiB층 두께가 감소하면 $H_i$가 증가하는 것을 확인하였다. 비정질 NiFeSiB층이 두꺼워지면 보통 계면의 기복을 유도하는 원주형성장(columnar growth)를 지연시키는데 유효하였다. 그러나 NiFeSiB층이 얇으면 표면거칠기는 증가하고 전자기적 Neel 결합 때문에 Hi는 커졌다.