• 한국전기전자재료학회논문지
• /
• 제20권8호
• /
• pp.680-684
• /
• 2007

In this study, we investigated the effects of structural and electrical properties of $(Ba_{0.6},\;Sr_{0.3},\;Ca_{0.1})TiO_3$ thick films with variation $Dy_2O_3$ contents. $(Ba_{0.6},\;Sr_{0.3},\;Ca_{0.1})TiO_3$ powders, prepared by the sol-gel method, were mixed organic vehicle. The BSCT thick films doped with 0.1, 0.3, 0.5, 0.7 mol% $Dy_2O_3$ were fabricated by the screen-printing techniques on the alumina substrates and the structural and dielectric properties were investigated with variation of $Dy_2O_3$ doping contents. All BSCT thick films were sintered at $1420^{\circ}C$, for 2hr. In the TG-DTA analysis, the formation of the polycrystalline perovskite phase was observed at around $670 ^{\circ}C$. In the XRD analysis, all BSCT thick films showed the cubic perovskite structure. The average thickness of BSCT thick films was approximately $65{\mu}m$. The Curie temperature decreased with increasing $Dy_2O_3$ amount. The relative dielectric constant and dielectric loss of BSCT thick films doped with $Dy_2O_3$ 0.1 mol% were 6267 and 2.6 %, respectively.

• 센서학회지
• /
• 제17권6호
• /
• pp.437-446
• /
• 2008

Single crystalline ${ZnIn_2}{Se_4}$ layers were grown on thoroughly etched semi-insulating GaAs (100) substrate at $400^{\circ}C$ with hot wall epitaxy (HWE) system by evaporating ${ZnIn_2}{Se_4}$ source at $630^{\circ}C$. The crystalline structure of the single crystalline thick films was investigated by the photoluminescence (PL) and Double crystalline X-ray rocking curve (DCRC). The carrier density and mobility of ${ZnIn_2}{Se_4}$ single crystalline thick films measured from Hall effect by van der Pauw method are $9.41{\times}10^{16}cm^{-3}$ and $292cm^2/V{\cdot}s$ at 293 K, respectively. The temperature dependence of the energy band gap of the ${ZnIn_2}{Se_4}$ obtained from the absorption spectra was well described by the Varshni's relation, $E_g(T)$=1.8622 eV-$(5.23{\times}10^{-4}eV/K)T^2$/(T+775.5 K). After the as-grown ${ZnIn_2}{Se_4}$ single crystalline thick films was annealed in Zn-, Se-, and In-atmospheres, the origin of point defects of ${ZnIn_2}{Se_4}$ single crystalline thick films has been investigated by the photoluminescence (PL) at 10 K. The native defects of $V_{Zn}$, $V_{Se}$, $Zn_{int}$, and $Se_{int}$ obtained by PL measurements were classified as a donors or acceptors type. And we concluded that the heat-treatment in the Se-atmosphere converted ${ZnIn_2}{Se_4}$ single crystalline thick films to an optical p-type. Also, we confirmed that In in ${ZnIn_2}{Se_4}$/GaAs did not form the native defects because In in ${ZnIn_2}{Se_4}$ single crystalline thick films existed in the form of stable bonds.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.873-876
• /
• 2000

Characteristics of piezoelectric thick films prepared by screen printing method were investigated. The piezoelectric thick films were printed using Pb(Mg,Nb)O$_3$-Pb(Zr,Ti)O$_3$system. The lower electrodes were coated with various thickness of Ag-Pd by screen printing to investigate the effect as a diffusion barrier and deposited with Pt by sputtering on Ag-Pd. The ceramic paste was prepared by mixing powder and binder with various ratios using three roll miller. The fabricated thick films were burned out at 650$^{\circ}C$ and sintered at 950$^{\circ}C$ in the O$_2$condition for each 20, 60min after printing with 350mesh screen. The thickness of piezoelectric thick film was 15∼20 $\mu\textrm{m}$ and the Ag-Pd electrode acted as a diffusion barrier above 3 $\mu\textrm{m}$ thickness. When the lower electrode Ag-Pd was 6 $\mu\textrm{m}$ and the piezoelectric thick films were sintered by 2nd step (650$^{\circ}C$/20min and 950$^{\circ}C$/1h) using paste mixed Pb(Mg,Nb)O$_3$-Pb(Zr,Ti)O$_3$$.$ MnO$_2$+ Bi$_2$O$_3$. V$_2$O$\_$5/ and binder in the ratio of 70:30, the remnant polarization of thick film was 9.1 ${\mu}$C /cm$^2$.

• Transactions on Electrical and Electronic Materials
• /
• 제7권6호
• /
• pp.279-282
• /
• 2006

[ $Pb(Zr_{0.4}Ti_{0.6}O_{3}\;and\;Pb(Zr_{0.6}Ti_{0.4})O_{3}$ ] paste were made and alternately screen-printed on the $Al_{2}O_{3}$ substrates. We have introduced a press-treatment to obtain a good densification of screen printed films. The porosity of the thick films was decreased with increasing the applied pressure and the thick films pressed at 60 MPa showed the dense microstructure and thickness of about $76\;{\mu}m$. The remanent polarization and coercive field increased with increasing applied pressure and the values for the PZT thick films pressed at 60 MPa were $17.04{\mu}C/cm^{2}$ and 78.09 kV/cm, respectively.

• 센서학회지
• /
• 제13권6호
• /
• pp.424-429
• /
• 2004

$Cr_{2}O_{3}$ thick films were fabricated by screen printing method on alumina substrates and annealed at $700^{\circ}C$, $800^{\circ}C$, and $900^{\circ}C$ in air, respectively. Structural properties examined by XRD and SEM showed (116) dominant $Cr_{2}O_{3}$ peak and increased grain sizes with the annealing. The resistance of the films decreased with increasing the annealing temperature. Gas sensing characteristics to $NH_{3}$, CO, $C_{4}H_{10}$, and NO gases showed sensitivity only to $NH_{3}$ gas. $Cr_{2}O_{3}$ thick films annealed at $700^{\circ}C$ had the sensitivity of about 15 % for 100 ppm $NH_{3}$ gas at the working temperature of $300^{\circ}C$. The thick films had good selectivity to the $NH_{3}$ gas. The response time to $NH_{3}$ gas was about 10 seconds.

• 한국세라믹학회지
• /
• 제37권2호
• /
• pp.140-144
• /
• 2000

Laser cutting of thick diamond films is studied using a low-power(10 W) copper vapor laser. Due to the existence of the saturation depth in laser cutting, thick diamond films are not easily cut by low-power lasers. In this study, we have adopted a low thermalconductivity underlayer of alumina and a heating stage (up to 500$^{\circ}C$ in air) to prevent the laser energy from consuming-out and, in turn, enhance the cutting efficiency. Aspect ratio increases twice fromm 3.5 to 7 when the alumina underlayer used. Adopting a heating stage also increases aspect ratio and more than 10 is obtained at higher temperatures than 400$^{\circ}C$. These results show that thick diamond films can be cut, with low-power lasers, simply by modifying the thermal property of underlayer.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2008년도 추계학술대회 초록집
• /
• pp.13-14
• /
• 2008

A high rate magnetron sputtering source (HRMSS) was employed to deposit thick copper films. The HRMSS was manufactured by changing the magnet size, arrangement, and field intensity. For the preparation of thick copper films, the copper sputtering conditions using HRMSS were characterized based on the deposition parameters such as discharge characteristics, I-V characteristics of the source, and change of deposition rate. The deposition rate of copper turned out to be more than 5 times than that of conventional magnetron sputtering source. Thick copper films having thickness of more than $20{\mu}m$ were prepared by using HRMSS. The morphology and orientation of the films were investigated by scanning electron microscopy and x-ray diffraction.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.180-182
• /
• 2004

Polycrystalline $BaTiO_3/SrTiO_3$ powder was prepared by sol-gel process and the multilayered thick films were prepared on the $Al_2O_3$ substrates by screen printing method. The films were sintered at $1400^{\circ}C$ for 2 hours in the air. The structural and dielectric properties were investigated, The X-ray diffraction (XRD) patterns indicate that the BST phase and porocity were formed in the interface of $BaTiO_3/SrTiO_3$ multilayered thick films. The dielectric constant and the dielectric loss of the BT/ST/BT/ST multilayered thick films were about 247 and 0.84% at 1MHz.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 추계학술대회 논문집 Vol.17
• /
• pp.400-403
• /
• 2004

The dielectric properties of $BaTiO_3/SrTiO_3$ multilayered thick films with printing times were investigated. $BaTiO_3/SrTiO_3$ thick films were deposited by Screen-printing method on alumina substrates. The obtained films were sintered at $1400^{\circ}C$ with bottom electrode(Pt) for 2hours. The structural and the dielectric properties were investigated for various printing times. The BST phase appeared in all of the $BaTiO_3/SrTiO_3$ mutilayered thick films. The $BaTiO_3/SrTiO_3$ multilayered thick film thickness, obtained by one printings, was $50{\mu}m$. The dielectric constant and dielectric loss of the $BaTiO_3/SrTiO_3$ multilayered thick film, obtained by five printings, were about 266, 0.8% at 1Mhz, respectively.

• Journal of Magnetics
• /
• 제6권1호
• /
• pp.9-12
• /
• 2001

The dependence of the magnetoimpedance effect (MI) on magnetic properties has been investigated in mumetal thin films prepared by rf magnetron sputtering. Coercivity of thin films prepared at 400 W was about 0.4 Oe, and the magnetic anisotropy field of films deposited under a uniaxial magnetic field decreased with increasing film thickness. The saturation magnetization of mumetal films increased with rising input power and thickness and was smaller than that of permalloy films. Transverse incremental Permeability (TPR) of films of 1$\mu m$ thick increased with increasing effective permeability. The magneto impedance ratio (MIR) was proportional to TPR in films 1$\mu m$ thick but in spite of lower effective permeability at higher thicknesses, MIR increased due to skin effect. The height of the double peaks in the MIR curves decreased with decreasing anisotropy and thickness. The maximum MIR value for a 4$\mu m$ thick 75% at 36.5 MHz.