• Journal of Energy Engineering
• /
• v.25 no.3
• /
• pp.9-17
• /
• 2016

In this study, a method for CO reduction using char-coal combustions was developed with lignin and glycerin as combustion improvers. The relationship between CO emission and the combustion improvers was confirmed by measuring the CO concentration. The experiment to determine the combustion characteristics was conducted using glycerin, which shows high combustibility at low temperatures, impregnated with lignin, which has a specific surface area. The combustibility, volatility, and CO concentration were measured using thermo-gravimetric analysis(TGA), and gas chromatography-mass spectrometry(GC-MS). This study presents the optimal CO reduction ratio, which occurred when the combustible material contained a 20% blend of combustion improvers. This resulted in a 20-30% CO reduction rate compared to that achieved with normal char-coal.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.17 no.2
• /
• pp.183-202
• /
• 2019

For design and performance assessment of a high-level radioactive waste (HLW) disposal system, it is necessary to understand the characteristics of coupled thermo-hydro-mechanical (THM) behavior. However, in previous studies for the Korean Reference HLW Disposal System (KRS), thermal analysis was performed to determine the spacing of disposal tunnels and interval of disposition holes without consideration of the coupled THM behavior. Therefore, in this study, TOUGH2-MP/FLAC3D is used to conduct THM modeling for performance assessment of the Korean Reference HLW Disposal System (KRS). The peak temperature remains below the temperature limit of $100^{\circ}C$ for the whole period. A rapid rise of temperature caused by decay heat occurs in the early years, and then temperature begins to decrease as decay heat from the waste decreases. The peak temperature at the bentonite buffer is around $96.2^{\circ}C$ after about 3 years, and peak temperature at the rockmass is $68.2^{\circ}C$ after about 17 years. Saturation of the bentonite block near the canister decreases in the early stage, because water evaporation occurs owing to temperature increase. Then, saturation of the bentonite buffer and backfill increases because of water intake from the rockmass, and bentonite buffer and backfill are fully saturated after about 266 years. The stress is calculated to investigate the effect of thermal stress and swelling pressure on the mechanical behavior of the rockmass. The calculated stress is compared to a spalling criterion and the Mohr-Coulumb criterion for investigation of potential failure. The stress at the rockmass remains below the spalling strength and Mohr-Coulumb criterion for the whole period. The methodology of using the TOUGH2-MP/FLAC3D simulator can be applied to predict the long-term behavior of the KRS under various conditions; these methods will be useful for the design and performance assessment of alternative concepts such as multi-layer and multi-canister concepts for geological spent fuel repositories.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.11
• /
• pp.7667-7671
• /
• 2015

Recently, Zinc coating is often used with environment friendly features and high performance. Generally The coating temperature is one of main factors for determining coating thickness and coating ability, so the optimal coating temperature is strongly required. In this paper, the thermo-flow simulation considering the air flow inside the coating rooms for analyzing the temperature distributions of Zinc spray coating room was performed. Two spray coating rooms, preheating room and drying room were all modeled by SolidWorks program and the temperature distributions were analyzed by Flow simulation program. The analysis results were verified with the measured data by thermal image camera. The characteristics of temperature distributions of the first spray room and the second spray room were understood and the results showed that the temperatures of two spray coating room were low compared with the target temperature $25^{\circ}C$. To the exclusion of heater addition, the simulation with all the same conditions exclusive the exhaust fan was performed, which showed that the temperatures of the first and the second spray rooms increased by $6.2^{\circ}C$ and $5.8^{\circ}C$. This analysis can be applicable for designing a new spray coating room for improving performance.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.18 no.9
• /
• pp.698-706
• /
• 2006

Experiment and numerical calculation have been peformed to investigate mixed convection heat transfer between inclined parallel plates. Particle image velocimetry (PIV) with thermo-sensitive liquid crystal (TLC) tracers is used for visualizing and analysis. This method allows simultaneous measurement of velocity and temperature fields at a given instant of time. Quantitative data of the temperature and velocity are obtained by applying the color-image processing to a visualized image, and neural network is applied to the color-to-temperature calibration. The governing equations are discretized using the finite volume method. The results are presented for the Reynolds number ranges from 0.004 to 0.062, the angle of inclination, ${\Theta}$, from 0 to 45 degree and Prandtl number of the high viscosity fluid is 909. The results show velocity, temperature and mean Nusselt numbers distributions. It is found that the periodic flow of mixed convection between inclined parallel plates is shown at $0^{\circ}{\leq}{\Theta}<30^{\circ}$, Re<0.062, and the flow pattern can be classified into three patterns which depend on Reynolds number and the angle of inclination. The minimum Nusselt numbers occur at Re=0.05 regardless of the angle of inclination.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.281-286
• /
• 2001

Tilting pad journal bearings have been widely used in a high speed rotating machinery, such as steam turbines and gas turbines, owing to their inherent stability characteristics. However, some peculiar fatigue failure in the babbitt metal due to spragging has been continuously occurred at the leading edge of the upper pads. The spragging is defined as the pad vibration initiated on the upper unloaded pads in a tilting pad journal bearing. This paper describes both several kinds of bearing failure related with spragging and the theoretical investigation on the prevention of the spragging phenomenon using the variation of preload. Results show that positive preload(m>0.5) assures all pads remain statically loaded under all operating conditions. For the change of design parameter to prevent spragging, thermo-hydrodynamic lubrication and rotor dynamic analysis were performed to verify temperature limitation on bearing and vibration problems on rotor bearing system.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1997.10a
• /
• pp.83-84
• /
• 1997

1. INTRODUCTION : Polyimides containing siloxane moiety(poly(imide siloxane), or polysiloxaneimide) have been synthesized because of their some merits over polyimide itseft. Polyimides have excellent thermal and mechanical properties but their poor solubility and processibility in their fullly imidized form give disadvantages in applications. Incorporation of siloxane units make it possible to increase solubility and processibility, and also impart impact resistance, low moisture uptake, low dielectric constant, thermo-oxidative resistance, good adhesion properties to substrate and etc.. Incorporation methods of siloxane groups into the polyimide was mainly copolymerization or terpolymerization between oligomeric dimethylsiloxane and aromatic dianhydride. A few methods of introducing siloxane units in functional groups of polyimide was reported. In our laboratory poly(amideimide siloxane) and poly(imide siloxane) were prepared and the study about their thermal kinetics was performed. In separation membrane area, polysiloxaneimides was utilized in pervaporation and gas separation. Polyimides in gas separation show high selectivity and very low permeability, and introduction of siloxane segments increase permeability with low decrease in selectivity. We aimed to introduce silicone segments into poly(amic acid) state and synthesize polymer partially imidized, and also show the gas separation characteristics of the synthesized polymer.

• Journal of computational fluids engineering
• /
• v.18 no.2
• /
• pp.17-25
• /
• 2013

The process of flow through porous media is of interest a wide range of engineering fields and areas, and the importance of fluid flow with a change in phase arises from the fact that many industrial processes rely on these phenomena for materials process, energy transfer. Especially, the flow phenomena of cryogenic liquid subjected to evaporation is of interest to investigate how the cryogenic liquid behaves in the porous structure. In this study, thermo physical properties, morphological properties of the glass wool with different bulk densities in terms of its temperature-dependence and permeability behaviors under different applying pressure are discussed. Using the experimentally determined properties, characteristics of two main experimental results are investigated. In addition, simulation results are used to realize the cryogenic liquid's flow in porous media, and are compared with experimental results. By using the experimentally determined properties, more reasonable results can be suggested in dealing with porous media flow.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.423-425
• /
• 2001

The Proper Orthogonal Decomposition (POD) technique was applied to investigate the effects of Reynolds number and the characteristics of the organized motions or coherent structures as a function of downstream position from x/D=2 to 6 in a turbulent axisymmetric shear layer at Reynolds numbers of 78,400, 117,600, and 156,800. Data were collected simultaneously using the 138 hot-wire probe used by Citriniti and George (2000). The POD was then applied to a double Fourier transform in time and azimuthal direction of the double velocity correlation tensor. The lowest azimuthal mode for all POD modes, which dominated the dynamics at x=D = 3 in the previous experiments, dies off rapidly downstream. This is consistent with a trend toward homogeneity in the downstream evolution, and suggests that some residual value may control the growth rate of the far jet. On the other hand, for the higher azimuthal modes, the peak shifts to lower mode numbers and actually increases with downstream distance. These mixing layer data, normalized by similarity variables for the mixing layer, collapse at all downstream positions and are nearly independent of Reynolds numbers.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.3
• /
• pp.47-54
• /
• 2015

In this study, effects of kneading treatment on the properties of hardwood bleached kraft pulp (HwBKP), softwood bleached kraft pulp (SwBKP) and hardwood bleached chemi-thermo-mechanical pulp (HwBCTMP) were elucidated with a laboratory two-shaft kneader. Kneading treatment was performed at 30% (w/w) of pulp concentration and the number of passes through the kneader was adjusted from 0 to 10 passes. Then, changes in properties of pulp fibers were evaluated. It was found that fiber characteristics were influenced by kneading treatment. Fiber length was decreased with kneading while other morphological properties such as fiber width, curl and kink became increased as the number of passes through the kneader increased from 0 to 5 passes. The magnitude of changes in the morphological properties of softwood chemical pulp was the largest, followed by hardwood chemical pulp. The morphological properties of HwBCTMP were little influenced by kneading treatment. Swelling of fiber measured by WRV was increased with kneading except of HwBCTMP.

• Journal of the Korean Ceramic Society
• /
• v.42 no.12 s.283
• /
• pp.821-826
• /
• 2005

Gadolinia-doped ceria nanopowder was prepared by glycine-nitrate combustion method with different glycine/nitrate mixing ratio. The characteristics of the synthesized powder were investigated by X-ray diffraction method, transmission electron microscopy, thermal gravity, differential thermal analysis and thermo-mechanical analysis. The smallest powder was obtained with glycine/nitrate ratio 1.00 and the lowest organic and water vapor contained powder was made with glycine/nitrate ratio 1.75. According to dilatometry, fast densification was occurred around $1000^{\circ}C$ and shows full density over $1300^{\circ}C$. Finally near-fully dense ceria electrolyte was fabricated with conventional sintering technique. Glycine-nitrate process yields fine nanopowders which enable low temperature sintering and fabrication of fully dense and nanostructured oxide electrolyte.