• Journal of Sensor Science and Technology
• /
• v.5 no.6
• /
• pp.15-24
• /
• 1996

In this study, as a part of the basic study for the application of optical fiber sensors to smart composite structures, the integrity of optical fiber sensors embedded within the composite structures was examined and then the laser signal transmitted through optical fiber sensors during the deformation of host structures was investigated. Firstly, it was found that bending test could be substituted for tensile test by comparing cumulative failure distribution based on weakest link theory and introducing the correction factor. Weibull parameters were obtained through the experiments and the correction factor was found to be applied to cumulative failure distribution derived from bending test. The integrity of embedded optical fiber sensors due to the thermal effect was evaluated by the comparison of the mean tensile strengths of cured and uncured optical fibers. Secondly, relationships between stress-strain curve obtained in tensile test of composite laminate and the intensity of laser signal transmitted through embedded optical fibers were examined and the possibility of the effective damage detection using optical fiber sensors was studied.

• Journal of Sensor Science and Technology
• /
• v.8 no.5
• /
• pp.400-406
• /
• 1999

Piezoresistive flow sensors with four different types of microbeam structures were fabricated using (100), n/$n^+$/n three-layer silicon wafer and their characteristics were investigated. Piezoresistors were formed through boron diffusion and its values were about $1\;k{\Omega}$. Three-dimensional silicon microbeams were constructed by porous silicon micromachining and curled microbeams were fabricated by the difference in the thermal expansion coefficient between silicon and metal. The output response of the fabricated sensor was evaluated through half- bridge. The output voltage increased with increasing length of microbeam at the same flow velocity, while the detectable measurement range extended with decreasing length of microbeam. The output voltage of the fabricated sensors were increased with quotient of 3.2 of the flow rate since the stress of the beam versus the gas flow showed non-linear characteristics.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2004.05a
• /
• pp.113-116
• /
• 2004

The materials showing high structure dispersion with functional properties were developed on the quartz base and those were obtained by mechano-chemical reaction technology. Depending on the processing conditions and subsequent applications the materials produced by mechano-chemical reaction show concurrently magnetic, dielectric and electrical properties. The obtained magnetic-electrical powders classified by aggregate complex of their features as segnetomagnetics, containing a dielectric material as a carrying nucleus, particularly the quartz on that surface one or more layers of different compounds were synthesized having thickness up to 10~50 nm showing magnetic, electrical properties and others. The similarity of the structure of surface layers of quartz particles subjected to mechano-chemical processing and nano-structure cluspol (clusters in a polymer matrics) material was also confirmed by the fact that the characteristics of ferromagnetic quartz of insulating nano-composite powder were changed with time, after its preparing process was completed. The magnetic permeability of the sample was decreasing within first two months down by 15~20 %. Then, the magnetic characteristics were almost stabilized steadily and continuously. The observed changes were related with defective structure of the particles, elastic stress relief, and changes of electron density and magnetic moment in deformation zones. This process of stabilization of the investigated properties could be intensified by the thermal annealing heat treatment in short time period of the nano-composite quartz powders at the temperature ranges of 100~15$0^{\circ}C$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.7
• /
• pp.1459-1464
• /
• 2009

Recently demand for large-capacity aluminum heat sinks has been increased as market for high power electricity expands and high-performance electronic products develop. While the brazed heat sinks are in particular preferred, it is almost impossible to manufacture them with an atmospheric continuous furnace due to insufficient heating rate and various thickness of the parent metals. Therefore, a new index batch furnace is developed and the process variables are optimized. Then, brazing efficiency and tensile stress are obtained for brazed parts of the heat sinks. Finally experiment as well as numerical analysis has been performed to compare thermal efficiency of the brazed heat sinks with that of the silicone-bonded heat sinks.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.387-387
• /
• 2007

기능성 나노소자를 구현할 수 있는 나노 소재로 0차원 구조의 양자점(quantum dot)과 1차원 구조의 양자선 및 나노선(nanorod)이 제안되고 있다. 나노선의 경우 나노스케일의 dimension, 앙자 제한 효과, 탁월한 결정성, self-assembly, internal stress등 기존의 벌크형 소재에서 발견할 수 없는 새로운 기능성이 나타나고 있어서 바이오, 에너지, 구조, 전자, 센서 등의 분야에서 활용되고 있다. 현재 국내외적으로 널리 연구되고 있는 나노선으로는 Si 및 Ge, $SnO_2$, SiC, ZnO 등이 있으며 특히, ZnO는 우수한 물리적 전기적 특성과 함께 나노선으로의 합성이 비교적 쉬워 주목받고 있는 재료이다. ZnO의 합성방법으로는 thermal CVD, MOCVD, PLD, wet-chemistry 등 다양한 방법이 사용되고 있다. 특히 MOCVD 법은 수직 정렬된 ZnO 나노막대를 합성하기가 매우 용이하다. 본 실험에서는 자체개발된 MOCVD 장비를 이용한 일차원 ZnO 나노선을 성장하였다. 이러한 ZnO 나노선의 성장은 사파이어 기판과 실리콘 기판 위에서 이루어졌으며 기판의 종류와 격자상수 불일도에 따른 상이한 성장과정을 온도에 따른 나노선 성장에서 관찰할 수 있었다. 사파이어 기판의 경우, 240도의 온도에서는 박막형상을 지닌 ZnO가 온도가 320도 이상으로 상승하면서 나노선으로 변함을 보였고, 실리콘 기판의 경우 380도 이상에서 기울기률 가진 나노선을 관찰하였으며, 420도에서는 나노선을 관찰 할 수 없었다. 또한 PL 장비를 이용한 PL 강도와 성장과정을 연관하여 생각하였을 때, 나노선의 기물기가 PL 강도비과 연관성을 가진다는 것을 측정을 통해 확인하였다.

• Nuclear Engineering and Technology
• /
• v.48 no.2
• /
• pp.533-544
• /
• 2016

This paper provides a reference to determine the seal performance of metallic O-rings for a reactor pressure vessel (RPV). A nonlinear elastic-plastic model of an O-ring was constructed by the finite element method to analyze its intrinsic properties. It is also validated by experiments on scaled samples. The effects of the compression ratio, the geometrical parameters of the O-ring, and the structure parameters of the groove on the flange are discussed in detail. The results showed that the numerical analysis of the O-ring agrees well with the experimental data, the compression ratio has an important role in the distribution and magnitude of contact stress, and a suitable gap between the sidewall and groove can improve the sealing capability of the O-ring. After the optimization of the sealing structure, some key parameters of the O-ring (i.e., compression ratio, cross-section diameter, wall thickness, sidewall gap) have been recommended for application in megakilowatt class nuclear power plants. Furthermore, air tightness and thermal cycling tests were performed to verify the rationality of the finite element method and to reliably evaluate the sealing performance of a RPV.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.6
• /
• pp.47-54
• /
• 2008

Fitting process carried out in the automobile transmission assembly line is classified into three classes; heat fitting, press fitting, and their combined fitting. Heat fitting is a method that heats gear to a suitable range under the tempering temperature and squeezes it toward the outer diameter of shaft. Its stress depends on the yield strength of gear. Press fitting is a method that generally squeezes gear toward that of shaft at room temperature by a press. Another method heats warmly gear and safely squeezes it toward that of shaft. Warm shrink fitting process for the automobile transmission part is now gradually increased, but the parts (shaft/gear) assembled by this process produced dimensional changes in both the outer diameter and profile of the gear. So that it may cause noise and vibration between gears. In order to solve these problems, we need an analysis of warm shrink fitting process, in which design parameters are involved; contact pressure according to fitting interference between outer diameter of shaft and inner diameter of gear, fitting temperature, and profile tolerance of gear. In this study, an closed form equation to predict contact pressure and fitting load was proposed in order to develop an optimization technique of the warm shrink fitting process and verified its reliability through the experimental results measured in the field and FEM, that is, thermal-structural coupled field analysis. Actual loads measured in the field was in good agreements with the results obtained by the theoretical and finite element analysis.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.12
• /
• pp.979-984
• /
• 2016

Recently, ball screws have been used in machine tools, robot parts, and medical instruments. The demand for ball screws of high precision and reduced size is increasing because of the growth of high value-added industries. Three types of ball screws are typically used: deflector type, end-cap type, and tube type. They are also classified from C0 to C9 according to the precision level. A deflector type ball screw can reduce the variation of rotational torque and the size of the nut of the ball screw is minimized. To ensure the reliable design of ball screws, it is important to perform a structural analysis. The purpose of this study is to perform a stability evaluation through analysis of a deflector type miniature ball screw for weapon systems. The analysis is performed through Finite Elements Method (FEM) simulation to predict characteristics such as deformation, stress, and thermal effects. The interference between the shaft and the deflector for smooth rotation are also studied. Based on the results of the analysis, the development of the deflector type miniature ball screw for weapon systems is performed.

• Tunnel and Underground Space
• /
• v.26 no.3
• /
• pp.154-165
• /
• 2016

This paper presents experimental results to investigate the affects of acidic solution under loading condition on rock properties. In the experiment, the variations of various rock properties including effective porosity, thermal conductivity, and etc were investigated with different pHs of solution and magnitudes of loading. The results show that the rock property change was increased with low pH under loading. It was predicted that chemical reaction rate would be increased in low pH. Below the crack initiation stress of the rock specimen, the variation of rock property change was reduced with increased loading. It could be explained with the reduced chemical reaction area by the compressional loading if there is no crack generation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.124-124
• /
• 2010

Much interest has been focused on InGaN-based materials and their quantum structures due to their optoelectronics applications such as light emitting diode (LED) and photovoltaic devices, because of its high thermal conductivity, high optical efficiency, and direct wide band gap, in spite of their high density of threading dislocations. Build-in internal field-induced quantum-confined Stark effect in InGaN/GaN quantum well LED structures results in a spatial separation of electrons and holes, which leads to a reduction of radiative recombination rate. Therefore, many growth techniques have been developed by utilizing lateral over-growth mode or by inserting additional layers such as patterned layer and superlattices for reducing threading dislocations and internal fields. In this work, we investigated various characteristics of InGaN multiple quantum wells (MQWs) LED structures grown on selectively wet-etched porous (SWEP) GaN template layer and compared with those grown on non-porous GaN template layer over c-plane sapphire substrates. From the surface morphology measured by atomic force microscope, high resolution X-ray diffraction analysis, low temperature photoluminescence (PL) and PL excitation measurements, good structural and optical properties were observed on both LED structures. However, InGaN MQWs LED structures grown on SWEP GaN template layer show relatively low In composition, thin well width, and blue shift of PL spectra on MQW emission. These results were explained by rough surface of template layer, reduction of residual compressive stress, and less piezoelectric field on MQWs by utilizing SWEP GaN template layer. Better electrical properties were also observed for InGaN MQWs on SWEP GaN template layer, specially at reverse operating condition for I-V measurements.