• 대한기계학회논문집A
• /
• 제35권12호
• /
• pp.1627-1633
• /
• 2011

사출금형은 일반적으로 다수개의 부품을 조립하여 제작되며, 특히 성형부(Core/Cavity)가 금형 형판 내부에 조립되는 구조를 갖는다. 이러한 구조로 인해 금형 조립부 경계면에서는 열접촉 저항이 발생하여 금형 내부의 열전달 특성에 영향을 미치게 된다. 최근 금형의 열접촉 저항이 성형부의 온도분포에 미치는 영향을 수치적으로 예측하기 위한 선행연구가 수행되었으며, 본 연구에서는 이에 기반하여 열-유동 연계해석을 적용함으로써 금형 내부의 열접촉 저항이 사출성형시 유동특성에 미치는 영향을 분석 하였다. 상기 해석결과와 실험결과와의 비교분석을 통해 금형의 열접촉 저항을 고려한 열-유동 연계해석이 기존의 해석방법과 비교할 때 사출성형 유동특성을 보다 향상된 신뢰성으로 예측할 수 있음을 확인하였다.

• Tribology and Lubricants
• /
• 제40권1호
• /
• pp.17-23
• /
• 2024

This study analyzes the thermal effects on the performance of an air foil thrust bearing (AFTB) using COMSOL Multiphysics to approximate actual bearing behavior under real conditions. An AFTB is a sliding-thrust bearing that uses air as a lubricant to support the axial load. The AFTB consists of top and bump foils and supports the rotating disk through the hydrodynamic pressure generated by the wedge effect from the inclined surface of the top foil and the elastic deformation of the bump foils, similar to a spring. The use of air as a lubricant has some advantages such as low friction loss and less heat generation, enabling air bearings to be widely used in high-speed rotating systems. However, even in AFTB, the effects of energy loss due to viscosity at high speeds, interface frictional heat, and thermal deformation of the foil caused by temperature increase cannot be ignored. Foil deformation derived from the thermal effect influences the minimum decay in film thickness and enhances the film pressure. For these reasons, performance analyses of isothermal AFTBs have shown few discrepancies with real bearing behavior. To account for this phenomenon, a thermal-fluid-structure analysis is conducted to describe the combined mechanics. Results show that the load capacity under the thermal effect is slightly higher than that obtained from isothermal analysis. In addition, the push and pull effects on the top foil and bump foil-free edges can be simulated. The differences between the isothermal and thermal behaviors are discussed.

• 한국유체기계학회 논문집
• /
• 제16권2호
• /
• pp.10-14
• /
• 2013

The present study conducts CFD analyses on the internal flow fields of roots type vacuum pumps of semiconductor fabrication facility, and the computed CFD results for internal pressure and temperature distributions are applied to structural analyses of the pumps. The coupled analysis results between flow and structure show that the deformation of pump structure is mainly resulted from the thermal expansion of gas in pump, and the deformed impeller and housing produce their severe contact and impact phenomena causing mechanical damage and fracture.

• 한국초전도ㆍ저온공학회논문지
• /
• 제22권4호
• /
• pp.51-56
• /
• 2020

In order to increase thrust of the space launch vehicle, liquid oxygen as an oxidizer and kerosene or liquid hydrogen as a fuel are generally used. The oxidizer tank and fuel tanks are manufactured by composite materials such as CFRP (Carbon Fiber Reinforced Plastic) to increase pay load. The thermal stress of the cryogenic propellant tank should be considered because it has large temperature gradient. In this study, to confirm the design integrity of the oxidizer tank of liquid oxygen, a numerical analysis was conducted on the thermal stress and temperature distribution of the tank for various charging speed of the cryogenic fluid from 100 ~ 900 LPM taking into account the evaporation rate of the liquid nitrogen by convective heat transfer outside the tank and boiling heat transfer inside the tank. The thermal stress was also calculated coupled with the temperature distribution of the CFRP tank. Based on the analysis results, the charging speed of the LN2 can majorly affects the charging time and the resultant thermal stress.

• 한국지반공학회논문집
• /
• 제38권9호
• /
• pp.45-52
• /
• 2022

암반내 불연속면이나 지반-구조물의 접촉면은 열-수리-역학적으로 연계된 거동 특성을 보이므로, 온전한 지배방정식에 근거한 경계면 요소의 개발이 필요하다. 본 논문은 경계면 요소에 대한 힘평형 방정식, 유체의 연속방정식 그리고 에너지 평형 방정식을 유도하였다. 그리고 경계면 요소에 대한 탄소성 역학 모델의 강성행렬을 제시하였다. 개발된 유한요소는 2차원 조건에서 변위는 6절점, 수압과 온도는 4절점을 사용한다. 단층내 유체 주입에 대한 완전연계된 THM 해석은 단층내의 유효응력 감소와 주위 암반의 온도 수축에 의한 주입압의 복합적인 변화을 모델링 할수 있었다. 하지만, 열적 현상을 무시한 HM해석은 수리-역학적 변수를 과다하게 산정하였다.

• Design & Manufacturing
• /
• 제14권2호
• /
• pp.1-6
• /
• 2020

Recently, research and commercialization related to the field of cell-based therapeutic drug development has been actively conducted. In order to maintain cell viability and prevent contamination, refrigeration preservation devices, such as CRF (controlled rate freezer) or vapor type LN2 tanks have been developed. On the other hand, the storage container for liquid nitrogen tanks currently on sale minimizes the flow structure to prevent structural defects when stored in a liquid nitrogen tank having a high thermal conductivity than vapor nitrogen. If the cell-based treatment drug is stored in the gaseous LN2 tank as it is, the cell survival after thawing is greatly reduced. It was estimated that the existing storage container structure was a factor that prevented the rapid entry and circulation of gaseous nitrogen into the container. Therefore, this study intends to propose a new supercellular storage container model that can maintain the mechanical strength while maximizing the fluid flow structure. To this end, we estimated that the structural change of the storage container effects on the equivalent stress formed around the through-holes of them when exposed to a cryogenic environment using thermal-structural coupled field analysis. As a result of storage experiments in the gas phase tank of the cell-based therapeutic agent using the developed storage container, it was confirmed that the cell growth rate was improved from 66% to 77%, which satisfied the transportation standards of the FDA(Food and Drug Administration) cell-based therapeutic agent.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.666-669
• /
• 2005

As computer power increased, the system with complex phenomenon has been analyzed with the help of CAE software which can handle the coupled physics, such as electromagnetic, structure, thermal and fluid physics. To predict the electromagnetic repulsion force and the temperature distribution of an air circuit breaker with electric contact mechanism, ANSYS/EMAG, FLOTRAN can be used. Although some assumptions and simplifications were introduced to simulate the model, results from the computational model were in good agreement with actual measurements obtained from experiments.

• Steel and Composite Structures
• /
• 제10권2호
• /
• pp.129-149
• /
• 2010

The objective of this study is to formulate a general 3D material-structural analysis framework for the thermomechanical behavior of steel-concrete structures in a fire environment. The proposed analysis framework consists of three sequential modeling parts: fire dynamics simulation, heat transfer analysis, and a thermomechanical stress analysis of the structure. The first modeling part consists of applying the NIST (National Institute of Standards and Technology) Fire Dynamics Simulator (FDS) where coupled CFD (Computational Fluid Dynamics) with thermodynamics are combined to realistically model the fire progression within the steel-concrete structure. The goal is to generate the spatial-temporal (ST) solution variables (temperature, heat flux) on the surfaces of the structure. The FDS-ST solutions are generated in a discrete form. Continuous FDS-ST approximations are then developed to represent the temperature or heat-flux at any given time or point within the structure. An extensive numerical study is carried out to examine the best ST approximation functions that strike a balance between accuracy and simplicity. The second modeling part consists of a finite-element (FE) transient heat analysis of the structure using the continuous FDS-ST surface variables as prescribed thermal boundary conditions. The third modeling part is a thermomechanical FE structural analysis using both nonlinear material and geometry. The temperature history from the second modeling part is used at all nodal points. The ABAQUS (2003) FE code is used with external user subroutines for the second and third simulation parts in order to describe the specific heat temperature nonlinear dependency that drastically affects the transient thermal solution especially for concrete materials. User subroutines are also developed to apply the continuous FDS-ST surface nodal boundary conditions in the transient heat FE analysis. The proposed modeling framework is applied to predict the temperature and deflection of the well-documented third Cardington fire test.

• 한국결정성장학회지
• /
• 제32권1호
• /
• pp.16-24
• /
• 2022

A computational study of combined thermal and solutal convection (double diffusive convection) in a sealed crystal growth reactor is presented, based on a two-dimensional numerical analysis of the nonlinear and strongly coupled partial differential equations and their associated boundary conditions. The average Nusselt numbers for the source regions are greater than those at the crystal regions for 9.73 × 10³ ≤ Gr_t ≤ 6.22 × 10⁵. The average Nusselt numbers for the source regions varies linearly and increases directly with the thermal Grashof number form 9.73 × 10³ ≤ Gr_t ≤ 6.22 × 10⁵ for aspect ratio, Ar (transport length-to-width) = 1 and 2. Additionally, the average Nusselt numbers for the crystal regions at Ar = 1 are much greater than those at Ar = 2. Also, the occurrence of one unicellular flow structure is caused by both the thermal and solutal convection, which is inherent during the physical vapor transport of Hg₂Br₂. When the aspect ratio of the enclosure increases, the fluid movement is hindered and results in the decrease of thermal buoyancy force.

• Tribology and Lubricants
• /
• 제35권1호
• /
• pp.77-86
• /
• 2019

The present study focuses on the effect of staggered integration factor (SIF) on Morton effect simulation results. The Morton effect is a synchronous rotordynamic instability problem caused by the temperature differential across the journal in fluid film bearings. Convection and conduction of heat in the thin film displaces the hot spot, which is the hottest circumferential position in the thin film, from -20 to 40 degrees ahead of the high spot, where the minimum film clearance is experienced. The temperature differential across the journal causes a bending moment and the corresponding thermal bow in the rotating frame acts like a distributed synchronous excitation in the fixed frame. This thermal bow may cause increased vibrations and continued growth of the synchronous orbit into a limit cycle. The SIF is developed assuming that the response of the rotor-lubricant-bearing dynamic system is much quicker than that of the bearing-journal thermal system, and it is defined as the ratio between the simulation time of the thermal system and the rotor-spinning period. The use of the SIF is unavoidable for efficient computing. The value of the SIF is chosen empirically by the software users as a value between 100 and 400. However, the effect of the SIF on Morton effect simulation results has not been investigated. This research produces simulation results with different values of SIF.