• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 추계학술발표대회 논문집
• /
• pp.183-186
• /
• 2003

Long shafts for power transmission should transmit torsional load with vibrational stability. Hybrid shafts made of unidirectional fiber-reinforced composite and metal have high fundamental bending natural frequency as well as high torque transmission capability. However, thermal residual stresses due to the coefficient difference of thermal expansion of the composite and metal are developed so that the high residual stresses decrease fatigue resistance of the hybrid shafts, especially at low operating temperatures. In this work, axial compressive preload was given to the shaft in order to change the residual stresses. Static and fatigue torsional tests were performed and correlated with stress analyses with respect to the preload and service temperature.

• Composites Research
• /
• 제28권4호
• /
• pp.244-248
• /
• 2015

When a small gear rotates at a very high speed over 40,000 rpm, frictional heat is generated on the gear surfaces. Thermal deformations and stresses arising from frictional heat may lower the efficiency and fatigue life of the high-speed gear. Especially, such frictional heat has much stronger effects on the performance of millimeter-sized high-speed gears used for surgical and dental hand-pieces, due to a small surface area. An analytical equation was derived to calculate frictional temperature on a mating gear surface and conduction heat transfer analysis was performed. Thermal deformation and contact stresses were then calculated using FEM for gears used for medical hand-pieces. The contact stresses of the meshed gear and pinion increase by 19.4% and 16.4%, respectively, when the frictional thermal deformations are considered.

• Advanced Composite Materials
• /
• 제17권3호
• /
• pp.301-317
• /
• 2008

The energy release rate associated with crack growth in adhesive double cantilever beam (DCB) specimens, including the effect of residual stresses, was formulated using beam theory. Because of the rotation of the asymmetric arms in the adhesive DCB specimens due to temperature change, it is necessary to correct the evaluated fracture toughness of the DCB specimens, specifically in the case of a large temperature change. This study shows that the difference between the true toughness and an apparent toughness due to the consequence of ignoring residual stresses can be calculated for a given specimen geometry and thermo-mechanical properties (e.g. coefficient of thermal expansion). The calculated difference in the energy release rates based on the present correction method is compared with that from FEM in order to verify the present correction method. The residual stress effects on the evaluation of the adhesive fracture toughness are discussed.

• 열처리공학회지
• /
• 제9권2호
• /
• pp.147-158
• /
• 1996

Generally, analytical consideration on the behaviour of metallic structures during quenching process, and analysis on the thermal stress and deformation after heat treatment are very important in presumption of crack and distorsion of quenched material. In this study a set of constitute equations relevant to the analysis of thermo elasto-viscoplastic materials with strain hysteresis during quenching process way presented on the basis of contimuum thermo-dynamics mechanics. The thermal stresses were numerically calculated by finite element technique of weighted residual method and the principle of virtual work. In the calculation process, the temperature depandency of physical and mechaniclal properties of the material in consideration. On the distribution of elasto-viscoplastic thermal stresses according to radial direction, axial and tangential stress are tensile stress(50MPa, 1.5GPa and 300MPa) in surface and compressive stress(-1.2GPa, -1.14GPa and -750MPa) in the inner part on the other hand, radial stress is tensile stress(900MPa) in area of analysis. According to axial direction, tangential stress gradients are average 60MPa/mm on the whole. The reversion of stress takes place at 11.5 to 16.8mm from the center in area of analysing.

• 대한토목학회논문집
• /
• 제28권6A호
• /
• pp.881-891
• /
• 2008

국내 최초로 시공되는 롤러다짐 콘크리트 댐(RCD)의 온도균열 관리방안 수립하기 위하여 RCD 공법의 시공특성인 층(layer) 타설 방식을 고려하여, 댐체의 온도분포 및 온도응력 해석을 수행하였다. RCD 공법은 수 백 개의 시공단계로 구성되어 있고, 실제 타설 층을 시공단계로 해석하는 것과 6층을 한 시공단계로 시공하는 경우를 비교하여 해석 단계의 단순화 가능성을 검토하였으며, 단위시멘트량이 $130kg/m^3$ 내외로 발열량이 매우 작은 RCD 배합의 경우에도 여름철에는 온도균열 지수가 1.0 이하로 나타나 온도관리의 필요성을 확인하였다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 춘계학술대회 논문집
• /
• pp.1205-1210
• /
• 2004

Cracks in the underground structures are mainly observed due to internal ununiformity of thermal stresses or restraint of structural movement in associate with rapid temperature gradient. Especially, thermal cracks are known to occur easily in a massive structure, but possibility of these depend on the amount of cement applied and ratio of span to height of the structure even though the thickness is less than specification‘s. Thus, this study aims at how to control thermal cracks in a massive subway structure and figures out an optimized construction method and procedure. As results of parametric study for length, height and outer temperature for concrete placement, it is found that hydration heats were not affected by both length and height of concrete placement but thermal stresses were greatly dependent. Most effective ways of controling thermal cracks were to fit a proper ratio of length to height of concrete placement and to decrease temperature of concrete placement as much as possible.

• Structural Engineering and Mechanics
• /
• 제58권4호
• /
• pp.627-639
• /
• 2016

The analysis of thermally induced stresses in engineering structures is a very important and necessary task with respect to design and modeling of pressurized containers, heat exchangers, aircrafts segments, etc. to prevent them from failure and improve working conditions. So, the purpose of this study is to investigate elasto-plastic thermal stresses and deformations in a thin annular plate embedded into rigid container. To this end, analytical research devoted to mathematically and physically rigorous stress/strain analysis is performed. In order to evaluate the effect of logarithmic thermal gradients, commonly applied to structures which incorporate thin plate geometries, different thermal parameters such as temperature mismatch and varying constraint temperature were introduced into the model of elastic perfectly-plastic annular plate obeying the von Mises yield criterion with its associated flow rule. The results obtained may be used in sensitive to temperature differences aircraft structures where the thermal effects on equipment must be kept in mind.

• Computers and Concrete
• /
• 제17권2호
• /
• pp.173-188
• /
• 2016

Generally, thermal stress induced by hydration heat causes cracking in mass concrete structures, requiring a thorough control during the construction. The prediction of the thermal stress is currently undertaken by means of numerical analysis despite its lack of reliability due to the properties of concrete varying over time. In this paper, a method for the prediction of thermal stress in concrete structures by adjusting thermal stress measured by a thermal stress device according to the degree of restraint is proposed to improve the prediction accuracy. The ratio of stress in concrete structures to stress under complete restraint is used as the degree of restraint. To consider the history of the degree of restraint, incremental stress is predicted by comparing the degree of restraint and the incremental stress obtained by the thermal stress device. Furthermore, the thermal stresses of wall and foundation predicted by the proposed method are compared to those obtained by numerical analysis. The thermal stresses obtained by the proposed method are similar to those obtained by the analysis for structures with internally as well as externally strong restraint. It is therefore concluded that the prediction of thermal stress for concrete structures with various boundary conditions using the proposed method is suggested to be accurate.

• 전산구조공학
• /
• 제8권1호
• /
• pp.173-186
• /
• 1995

2가지 이상의 재질로 결합된 구조물이 온도 변화를 받으면 열응력이 발생한다. 이러한 응력은 재질간의 열팽창계수가 서로 상이하여 생긴다. 본 논문에서는 균일한 온도변화를 받는 복합 재료로 이루어진 축대칭 원판(disk)에 대한 응력상태를 구하는 공식을 유도하였다. 먼저, 재료역학원리를 이용하여 근사해를 구한 후, Eigenfunction series를 전개하여 탄성학적인 정확해(Exact Solution)를 구하였다. 또한 정확해는 유한요소법으로 구한 해와 비교하였다. 상기 근사해로는 연계면에서의 응력분포를 예측하는 데 어려움이 있었으나, 정확해는 유한요소법으로 구한 결과와 대체로 일치하고 있어 응력분포를 충분히 예측할 수 있었다. 따라서, 본 논문에서 구한 정확해(Exact Solution) 공식은 복합재료로 구성된 구조물의 연계면에서의 응력분포를 결정하는 데 유용하다.

• 터널과지하공간
• /
• 제18권5호
• /
• pp.343-354
• /
• 2008

시추공을 이용한 초기응력 측정을 위한 새로운 방법을 제안하였다. 이 새로운 개념의 측정법은 기본적으로 응력 해방과 파쇄 기술을 결합한 방법이다. 액화질소와 같은 극저온 액체를 이용하여 시추공 주변의 인장 열응력을 유도하여 시추공 주변의 응력을 해방시킬 수 있다. 종국에는 시추공 주변의 인장 강도가 암반의 인장 강도에 초기 지압으로 존재하는 압축 응력의 합을 초과할 때 시추공벽에 균열을 발생시킨다. 이와 같은 개념을 인장 응력으로부터 초기 응력 수준을 평가하는데 적용하기 위한 이론적 분석을 수행하였다. 또한, 제안한 방법의 유효성을 검토하기 위해 FLAC3D를 이용한 열-역학 상호작용 연속체 해석을 수행하였다. 사전 이론적 검토 및 수치해석으로부터 저온 열균열 발생 현상을 이용한 초기 응력 측정법이 시추공벽에서의 인장 균열 형성을 감시하고 시추공벽에서의 균열 개시 시점의 온도를 기록함으로써 초기 응력을 정밀하게 측정할 수 있음을 확인하였다.