• Plant Journal
• /
• v.17 no.2
• /
• pp.32-41
• /
• 2021

Recently, air environmental issues such as fine dust have rapidly emerged as national issues, and intensive environmental regulations are being applied to coal-fired power plants. This study introduces the case of improving the performance of desulfurization facilities for removing sulfur oxides and dust, which are the main air pollutant emitters of coal-fired power plants, and conducted four case studies to improve the performance of 1,000 MW power plants currently in operation and carried out construction. Liquid ratio was increased by remodeling the absorption tower of desulfurization facilities, and vaporization reaction was promoted by increasing the flow rate of oxidized air. In addition, the gas heater leakage rate was improved to improve the efficiency of final desulfurization facilities. It is expected that performance improvement work considering harmony with existing facilities will satisfy the regulations(25ppm of sulfur oxides, 5mg/Sm³) that will be applied from 2023, and can be referred to other thermal power plants for review and application.

• Geomechanics and Engineering
• /
• v.33 no.1
• /
• pp.29-40
• /
• 2023

Xanthan gum and starch compound biopolymer (XS), an environmentally friendly soil-binding material produced from natural resources, has been suggested as a slope protection material to enhance soil strength and erosion resistance. Insufficient wet strength and the consequent durability concerns remain, despite XS biopolymer-soil treatment showing high strength and erosion resistance in the dried state, even with a small dosage of soil mass. These concerns need to be solved to improve the field applicability and post-stability of this treatment. This study explored the utilization of an alkaline-based cation crosslinking method using calcium hydroxide and sodium hydroxide to induce non-thermal gelation, resulting in the enhancement of the wet strength and durability of biopolymer-treated soil. Laboratory experiments were conducted to assess the unconfined compressive strength and cyclic wetting-drying durability performance of the treated soil using a selected recipe based on a preliminary gel formation test. The results demonstrated that the uniformity of the gel structure and gelling time varied depending on the ratio of crosslinkers to biopolymer; consequently, the strength of the soil was affected. Subsequently, site soil treated with the recipe, which showed the best performance in indoor assessment, was implemented on the field slope at the bridge abutment via compaction and pressurized spraying methods to assess feasibility in field implementation. Moreover, the variation in surface soil hardness was monitored periodically for one year. Both slopes implemented by the two construction methods showed sufficient stability against detachment and scouring, with a higher soil hardness index than the natural slope for a year.

• Advances in materials Research
• /
• v.11 no.2
• /
• pp.121-146
• /
• 2022

In the recent years, the use of agricultural waste in green cement mortar and concrete production has attracted considerable attention because of potential saving in the large areas of landfills and potential enhancement on the performance of mortar. In this research, microparticles of palm oil fuel ash (POFA) obtained from a multistage thermal and mechanical treatment processes of raw POFA originating from palm oil mill was utilized as a pozzolanic material to produce high-performance cement mortar (HPCM). POFA was used as a partial replacement material to ordinary Portland cement (OPC) at replacement levels of 0, 5, 10, 15, 20, 25, 30, 35, 40% by volume. Sand with particle size smaller than 300 ㎛ was used to enhance the performance of the HPCM. The HPCM mixes were tested for workability, compressive strength, ultrasonic pulse velocity (UPV), porosity and absorption. The results portray that the incorporation of micro POFA in HPCMs led to a slight reduction in the compressive strength. At 40% replacement level, the compressive strength was 87.4 MPa at 28 days which is suitable for many high strength applications. Although adding POFA to the cement mixtures harmed the absorption and porosity, those properties were very low at 3.4% and 11.5% respectively at a 40% POFA replacement ratio and after 28 days of curing. The HPCM mixtures containing POFA exhibited greater increase in strength and UPV as well as greater reduction in absorption and porosity than the control OPC mortar from 7 to 28 days of curing age, as a result of the pozzolanic reaction of POFA. Micro POFA with finely graded sand resulted in a dense and high strength cement mortar due to the pozzolanic reaction and increased packing effect. Therefore, it is demonstrated that the POFA could be used with high replacement ratios as a pozzolanic material to produce HPCM.

• Nuclear Engineering and Technology
• /
• v.56 no.6
• /
• pp.2153-2162
• /
• 2024

The purpose of this study is to develop a high-energy neutron shielding material applied in proton therapy environment. Composite shielding material consisting of 10.00 wt% boron carbide particles (B₄C), 13.64 wt% surface-modified cross-linked polyethylene (PE), and 76.36 wt% tungsten particles were fabricated by hot-pressure sintering method, where the optimal ratio of the composite is determined by the shielding effect under the neutron field generated in typical proton therapy environment. The results of Differential Scanning Calorimetry measurements (DSC) and tensile experiment show that the composite has good thermal and mechanical properties. In addition, the high energy-neutron shielding performance of the developed material was evaluated using cyclotron proton accelerator with 100 MeV proton. The simulation shows a 99.99% decrease in fast neutron injection after 44 cm shielding, and the experiment result show a 99.70% decrease. Finally, the shielding effect of replacing part of the shielding material of the proton therapy hall with the developed material was simulated, and the results showed that the total neutron injection decreased to 0.99‰ and the neutron dose reduced to 1.10‰ before the enhanced shielding. In summary, the developed material is expected to serve as a shielding enhancement material in the proton therapy environment.

• Radiation Oncology Journal
• /
• v.11 no.1
• /
• pp.51-58
• /
• 1993

We tried to establish the theoretical basis of clinical use of combined modality of hyperthermia and radiation therapy. For this purpose, we made an in vitro experiment in order to get the synergistic and/or additive effects on the cell killing of hyperthermia combined with radiation therapy by using the microwave-hyperthermia machine already installed at our department. In our experiment, we use two human cell lines: MKN-45 (adenocarcinoma of stomach) and K-562 (leukemia cell lines). In cases of combined treatments of hyperthermia and gamma-irradiation, the therapeutic effect was the highest in the simultaneous trial. Hyperthermia after gamma irradiation showed slightly higher therapeutic effect than that before irradiation without significant difference, but its effect was the same in the interval of 6 hours between hyperthermia and irradiation. The higher temperature and the longer treatment time were applied, the higher therapeutic effects were observed. We could observe the thermoresistance by time elapse at $43^{\circ}C$. When hyperthermia was done for 30 minutes at the same temperature, thermal enhancement ratio (TER) at DO. 01 (dose required surviving fraction of 0.01) were $2.5{\pm}0.08,\;3.75{\pm}0.18$, and $5.0{\pm}0.15\;at\;436{\circ}C,\;44^{\circ}C,\;and\;45^{\circ}C$ respectively in K-562 leukemia cell lines. Our experimental data showed that more cell killing effect can be obtained in the leukemia cell lines, although they usually are known to be radiosensitive, when treated with combined hyperthermia and radiation therapy. Furthermore, our data show that leukemia cell lines may have various intrinsic radiosensitivity, especially in vitro experiments. The magnitude of cell killing effect, however, will be less than that of MKN-45.

• Polymer(Korea)
• /
• v.39 no.3
• /
• pp.453-460
• /
• 2015

Engineering the polylactide via stereocomplexation with supercritical fluid (SCF) technology paved way to fabricate polymers with enhanced thermal and mechanical properties. We aimed to establish a SCF medium with excellent solubility for PLA without any additional solvent/co-solvent. We, therefore, employed supercritical dimethyl ether to synthesize 100% stereocomplex polylactide from high molecular weight homopolymers with an excellent yield. The remarkable solubility of the homopolymers in dimethyl ether is the key for quick conversion to s-PLA. This study proves a rapid synthesis route of dry s-PLA powder with sc-DME at 250 bar, $70^{\circ}C$ and 1.5 h, which are reasonably achievable processing parameters compared to the conventional methods. The degree of stereocomplexation was evaluated under the effect of pressures, temperatures, times, homopolymer-concentrations and molecular weights. An increment in the degree of stereocomplexation was observed with increased temperature and pressure. Complete conversion to s-PLA was obtained for PLLA and PDLA with $M_n{\sim}200kg{\cdot}mol^{-1}$ with a total homopolymer to total DME ratio of 6:100% w/w at prescribed reaction conditions. The degree of stereocomplexation was determined by DSC and confirmed by XRD. Considerable improvement in thermo-mechanical properties of s-PLA was observed. DSC and TGA analyses proved a $50^{\circ}C$ enhancement in melting transition and a high onset temperature for thermal degradation of s-PLA respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.311-311
• /
• 2016

최근 고성능 디스플레이 개발이 요구되면서 기존 비정질 실리콘(a-Si)을 대체할 산화물 반도체에 대한 연구 관심이 급증하고 있다. 여러 종류의 산화물 반도체 중 a-IGZO (amorphous indium-gallium-zinc oxide)가 높은 전계효과 이동도, 저온 공정, 넓은 밴드갭으로 인한 투명성 등의 장점을 가지며 가장 연구가 활발하게 보고되고 있다. 기존에는 SG(단일 게이트) TFT가 주로 제작 되었지만 본 연구에서는 DG(이중 게이트) 구조를 적용하여 고성능의 a-IGZO 기반 박막 트랜지스터(TFT)를 구현하였다. SG mode에서는 하나의 게이트가 채널 전체 영역을 제어하지만, double gate mode에서는 상, 하부 두 개의 게이트가 동시에 채널 영역을 제어하기 때문에 채널층의 형성이 빠르게 이루어지고, 이는 TFT 스위칭 속도를 향상시킨다. 또한, 상호 모듈레이션 효과로 인해 S.S(subthreshold swing)값이 낮아질 뿐만 아니라, 상(TG), 하부 게이트(BG) 절연막의 계면 산란 현상이 줄어들기 때문에 이동도가 향상되고 누설전류 감소 및 안정성이 향상되는 효과를 얻을 수 있다. Dual gate mode로 동작을 시키면, TG(BG)에는 일정한 positive(or negative)전압을 인가하면서 BG(TG)에 전압을 가해주게 된다. 이 때, 소자의 채널층은 depletion(or enhancement) mode로 동작하여 다른 전기적인 특성에는 영향을 미치지 않으면서 문턱 전압을 쉽게 조절 할 수 있는 장점도 있다. 제작된 소자는 p-type bulk silicon 위에 thermal SiO2 산화막이 100 nm 형성된 기판을 사용하였다. 표준 RCA 클리닝을 진행한 후 BG 형성을 위해 150 nm 두께의 ITO를 증착하고, BG 절연막으로 두께의 SiO2를 300 nm 증착하였다. 이 후, 채널층 형성을 위하여 50 nm 두께의 a-IGZO를 증착하였고, 소스/드레인(S/D) 전극은 BG와 동일한 조건으로 ITO 100 nm를 증착하였다. TG 절연막은 BG 절연막과 동일한 조건에서 SiO2를 50 nm 증착하였다. TG는 S/D 증착 조건과 동일한 조건에서, 150 nm 두께로 증착 하였다. 전극 물질과, 절연막 물질은 모두 RF magnetron sputter를 이용하여 증착되었고, 또한 모든 patterning 과정은 표준 photolithography, wet etching, lift-off 공정을 통하여 이루어졌다. 후속 열처리 공정으로 퍼니스에서 질소 가스 분위기, $300^{\circ}C$ 온도에서 30 분 동안 진행하였다. 결과적으로 $9.06cm2/V{\cdot}s$, 255.7 mV/dec, $1.8{\times}106$의 전계효과 이동도, S.S, on-off ratio값을 갖는 SG와 비교하여 double gate mode에서는 $51.3cm2/V{\cdot}s$, 110.7 mV/dec, $3.2{\times}108$의 값을 나타내며 훌륭한 전기적 특성을 보였고, dual gate mode에서는 약 5.22의 coupling ratio를 나타내었다. 따라서 산화물 반도체 a-IGZO TFT의 이중게이트 구조는 우수한 전기적 특성을 나타내며 차세대 디스플레이 시장에서 훌륭한 역할을 할 것으로 기대된다.

• Composites Research
• /
• v.36 no.2
• /
• pp.132-139
• /
• 2023

A linerless composite propellant tank was designed and manufactured by using the carbon fiber-reinforced composite materials which have superior strength-to-weight ratio in order to reduce weight of the tank. In this research, we designed a sub-scale composite propellant tank with a diameter of 800 mm to withstand an MEOP of 1.7 MPa. We manufactured the boss of the tank by using the same composite materials to reduce the thermal expansion difference between the boss and the secondary-bonded composite layers of the barrel in the cryogenic environment. We used the collapsible mandrel to manufacture the tank without any liner. The mandrel was made from epoxy-based composite tooling prepregs to reduce weight of the mandrel. We manufactured the test tanks by laying up the carbon fiber fabric prepregs manually on the mandrel and then applying the autoclave cure process. We performed a proof test, a helium tightness test, a repeated pressurization test, and a burst test in room temperature. The test results demonstrate that the proposed design and manufacture process satisfies all strength requirements as well as an anti-leakage requirement.

• Radiation Oncology Journal
• /
• v.5 no.1
• /
• pp.13-21
• /
• 1987

The effect of local hyperthermia of 41 to $43^{\circ}C$ for 30 minutes on radiosensitivity of normal tissue was studied utilizing jejunal crypt microcolony assay. Hyperthermia of this range enhanced the radiation effect and the effect was mainly additive without significant effect on the slopes of cell survival curves. At the isoeffect level of 20 microcolony formation, the thermal enhancement ratio was 1.02, 1.10 and 1.39 for $41^{\circ},\;42^{\circ}\;and\;43^{\circ}C$, respectively. The distribution of microcolony formation along the circumference of jejunum was not uniform, having more colonies around the mesenteric border, and this suggests the effect of uneven cooling by blood circulation.