• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1933-1938
• /
• 2004

Nucleate boiling experiments with constant wall temperature of heating surface were performed using R113 for almost saturated pool boiling conditions. A microscale heater array and Wheatstone bridge circuits were used to maintain a constant wall temperature condition and to measure the heat flow rate with high temporal and spatial resolutions. Bubble images during the bubble growth were taken as 5000 frames a sec using a high-speed CCD camera synchronized with the heat flow rate measurements. The geometry of the bubble during growth time could be obtained from the captured bubble images. The bubble growth behavior was analyzed using the new dimensionless parameters for each growth regions to permit comparisons with previous results at the same scale. We found that the new dimensionless parameters can describe the whole growth region as initial and later respectively. The comparisons showed good agreement in the initial and thermal growth regions. The required heat flow rate for the volume change of the observed bubble was estimated to be larger than the instantaneous heat flow rate measured at the wall. Heat, which is different from the instantaneous heat supplied through the heating wall, can be estimated as being transferred through the interface between bubble and liquid even with saturated pool conditions. This phenomenon under a saturated pool condition needs to be analyzed and the data from this study can supply the good experimental data with the precise boundary condition (constant wall temperature).

• Tribology and Lubricants
• /
• 제24권4호
• /
• pp.196-204
• /
• 2008

In this study, the pressure distributions on the oil film of piston pin bearings are found by two-dimensional lubrication analysis in order to help the optimum design of the bearings of piston pin. The lubrication analysis is carried out together with an equation related with the oil pressure-viscosity index. The oil film pressure distribution is used as an input data for pressure boundary conditions at the piston pin-boss surface. Finally, the piston pin-boss stress distribution coupled with the thermal stress is calculated, and then compared with the results of the stress analysis which is not counted with the oil film pressure boundary condition.

• Journal of Mechanical Science and Technology
• /
• 제18권6호
• /
• pp.990-1001
• /
• 2004

The retention of a molten pool vessel cooled by internal vessel reflooding and/or external vessel reactor cavity flooding has been considered as one of severe accident management strategies. The present numerical study investigates the effect of both internal and external vessel mixed cooling on an internally heated molten pool. The molten pool is confined in a hemispherical vessel with reference to the thermal behavior of the vessel wall. In this study, our numerical model used a scaled-down reactor vessel of a KSNP (Korea Standard Nuclear Power) reactor design of 1000 MWe (a Pressurized Water Reactor with a large and dry containment). Well-known temperature-dependent boiling heat transfer curves are applied to the internal and external vessel cooling boundaries. Radiative heat transfer has been considered in the case of dry internal vessel boundary condition. Computational results show that the external cooling vessel boundary conditions have better effectiveness than internal vessel cooling in the retention of the melt pool vessel failure.

• Korean Chemical Engineering Research
• /
• 제52권2호
• /
• pp.199-204
• /
• 2014

2성분 응고계에서 다공성 mush 층에서의 조성 대류는 생성되는 제품의 질에 영향을 준다. 본 연구에서는 일정한 속도로 응고되는 mush 층을 고려하였다. 선형 안정성 이론을 사용하여 mush 층에 대한 교란방정식을 유도하였고, 기본상태 온도장과 mush 층에서 기공률의 분포를 수치해법으로 조사하였다. 과열량이 클 때 mush 층의 두께는 열경계층의 두께에 비해 상대적으로 작았다. 과열량이 감소함에 따라 mush 층의 두께를 기준으로 한 Rayleigh 수는 증가하였고, mush 층은 조성 대류에 대해 안정해졌다. mush 층의 윗면에 등온조건을 적용한 경우보다 온도 및 열속의 연속조건을 액체-mush 계면에 적용한 경우에 임계 Rayleigh 수가 더 작게 얻어졌다.

• 대한기계학회논문집B
• /
• 제29권4호
• /
• pp.460-468
• /
• 2005

Analyses of flow and heat transfer characteristics and shape optimization of internally finned circular tubes have been performed for three-dimensional periodically fully developed turbulent flow and heat transfer. CFD and mathematical optimization are coupled in order to optimize the shape of heat exchanger. The design variables such as fin widths $(d_{1},\;d_{2})$ and fin height (h) are numerically optimized by minimizing the pressure loss and maximizing the heat transfer rate for limiting conditions of $d_{1}=0.2\~1.5\;mm,\;d_{2}=0.2\~1.5\;mm,$ and $h=0.2\~1.5mm$. Due to the periodic boundary conditions along main flow direction, the three layers of meshes are considered. The flow and thermal fields are predicted using the finite volume method and the optimization is carried out by means of the sequential quadratic programming (SQP) method which is widely used in the constrained nonlinear optimization problem.

• Coupled systems mechanics
• /
• 제10권1호
• /
• pp.39-60
• /
• 2021

The present paper is concerned with the study of nonlinear ultrasonic waves in a magneto thermo (MT) elastic armchair single-walled carbon nanotube (ASWCNT) resting on polymer matrix. The analytical formulation is developed based on Eringen's nonlocal elasticity theory to account small scale effect. After developing the formal solution of the mathematical model consisting of partial differential equations, the frequency equations have been analyzed numerically by using the nonlinear foundations supported by Winkler-Pasternak model. The solution is obtained by ultrasonic wave dispersion relations. Parametric work is carried out to scrutinize the influence of the non local scaling, magneto-mechanical loadings, foundation parameters, various boundary condition and length on the dimensionless frequency of nanotube. It is noticed that the boundary conditions, nonlocal parameter, and tube geometrical parameters have significant effects on dimensionless frequency of nano tubes. The results presented in this study can provide mechanism for the study and design of the nano devices like component of nano oscillators, micro wave absorbing, nano-electron technology and nano-electro- magneto-mechanical systems (NEMMS) that make use of the wave propagation properties of armchair single-walled carbon nanotubes embedded on polymer matrix.

• 한국전산유체공학회지
• /
• 제21권3호
• /
• pp.98-109
• /
• 2016

The flow and heat transfer characteristics of a heat exchanger having rectangular pin-fin in the flow direction have been investigated numerically. On the bottom plate, the convective boundary conditions for the hot side was given, and the fins were arranged in a channel-type geometric model using the periodic boundary condition in the span-wise direction. Three-dimensional numerical calculations for the flow and conjugate heat transfer problem were conducted using SIMPLE algorithm and $k-{\varepsilon}$ turbulence model. For the slanted pin-fin models, it was found that the downward cooling flow is generated due to the downward pressure gradient component, which can enhance the heat transfer performance near the bottom surface and the fin stem region. Four different inclined angles were considered in the Reynolds number range of 13,500-55,000. The aero-thermal performance of the slanted pin-fin heat exchangers, such as the volume and area goodness factors, were summarized and compared with the baseline plate-fin type heat exchanger quantitatively.

• 대한기계학회논문집
• /
• 제19권7호
• /
• pp.1675-1683
• /
• 1995

A numerical study of the fluid flow and heat transfer characteristics of the two-dimensional impingement jet with a confinement plate has been carried out. The fluid flow was calculated by solving the full Navier-Stokes equation. In doing that, the well known SIMPLER algorithm was used and the trouble making convection term was discretized according to QUICKER scheme. The energy equation was simply solved by using the SOR method. For the Reynolds number of 10000, two channel heights, say 1.5 and 3.0 times the jet exit width, and two thermal boundary conditions constant wall temperature and constant wall heat flux were considered. Discrete heat sources were flush mounted along the impingement plate at a distance of 0, 2, 3, 4, 5, 6, 10, 12, times the jet exit width from the stagnation point. The length of each heat source is 4 times the jet exit width long. The Nusselt number averaged over each heat source was compared with experiment. Comparison shows that both calculations and experiment have the secondary peak of Nusselt number at downstream of stagnation point, even though there is a little quantitative difference in between. The difference is believed due to abscure thermal boundary condition in experiment and also accuracy of turbulence model used. The secondary peak is shown to be caused by rigorous turbulent flow motion generated as the wall jet flow is retarded and developes into the channel flow without flow reversal.

• 한국안광학회지
• /
• 제16권4호
• /
• pp.409-415
• /
• 2011

목적: 초점거리의 비가 3:1인 아나모픽 렌즈를 적용하여 탐지거리를 증대시키는 열상 광학계를 설계하였다. 방법: 화각이 $50^{\circ}{\sim}60^{\circ}$, 초점거리는 수평방향 36 mm, 수직방향 12 mm로 구속조건을 정하였다. 구속조건으로 f-number는 4, 화소 크기는 $15{\mu}m{\times}15{\mu}m$, 한계 분해능은 33l p/mm에서 25% 이상으로 제한하였다. 재질은 Si, ZnS, ZnSe를 사용하였으며 파장영역은 4.8 ${\mu}m$, 4.2 ${\mu}m$, 3.7 ${\mu}m$로 설정하였다. 설계한 열상 카메라의 광학적 성능 및 탐지거리와 나르시서스, 비열화를 분석하였다. 결과: 열상 광학계의 초점거리는 Y축 방향이 12 mm, X축 방향이 36 mm를 만족하였으며 f-number는 4를 만족하였다. 전장의 길이는 76 mm로 시스템의 전반적인 부피를 감소시켰다. 구면수차와 비점수차는 ${\pm}$0.10내로 2 pixel 크기보다 작게 나타났다. 왜곡수차는 10%이내로써 열상 카메라로 사용하는데 문제가 없음을 확인하였다. 광학계 MTF 성능은 33l p/mm에서 full field 까지 25%이상으로 구속조건을 만족하였다. 설계된 열상 광학계는 2.9 km까지 탐지할 수 있으며 4면을 제외한 나머지 면들의 나르시서스 값을 줄여 상 번짐이 감소하였다. 민감도 분석을 통해 5번째 렌즈를 보상자로 선택하여 온도 변화에 따른 MTF 해상력을 높였다. 결론: 아나모픽 렌즈를 적용해서 설계한 열상 광학계의 광학적 성능은 구속조건을 만족하였으며 더 긴 탐지거리와 나르시서스의 감소, 온도에 따른 해상력이 증가됨을 확인하였다.

• 한국생산제조학회지
• /
• 제6권4호
• /
• pp.108-117
• /
• 1997

A continuum analysis has been performed for the application to the thermo-elasto-plastic behavior in a discontinuous metal matrix composite. an FEM (Finite Element Method) analysis was implemented to obtain the internal field quantities of composite as well as overall composite behavior and an experiment was demonstrated to compare with the numerical simulation . As the procedure, a reasonably optimized FE mesh generation, the appropriate imposition of boundary condition , and the relevant post processing such as elastoplastic thermomchanical analysis were taken into account. For the numerical illustration, an aligned axisymmetric single fiber model with temperature dependent material properties and precipitation hardening effect has been employed to assess field quantities. It was found that the residual stresses are induced substantially by the temperature drop during the thermal treatment and that the FEM results of the vertically and horizontally constrained model give a good agreement with experimental data.with non-woven carbon mat is about 24% higher than that of composite materials without non-woven carbon mat. Transverse tensile strength and torughness also increase by inserting non-woven carbon mat between layers.